Great video! Heres an easy way to measure your wheel for your speedo: Use some chalk to draw a line from your tyre onto the floor. Then roll your scoot forward until the chalk is perpendicular to the floor again and draw a second line onto the floor. Now use a tape measure to measure the distance between the two chalk marks on the floor.
If there only was some kind of formula that let's you calculate the circumference of a circle using nothing but the radius or even the diameter... Any thoughts, Archimedes of Syracuse???
@@MOPBOYZ dude you should definitely do a video on bringing her back that would be a sick video! Thanks for being the best scooter channel on UA-cam, I just bought a 150cc gy6 to start messing around on and give my 81 Honda a break 😂. Thanks dude
On a carbed zuma the best mods - front pulley take nut off, remove washer, put nut back on without, this adds 5mph top end. Blue clutch rollers and springs. 70cc head, not 100cc trust me. Variator. Leave front pully alone. Kevlar belt. Leo vince zx exhaust baffles removed and exhaust head drilled open. Larger rear spring/shock to accommodate the larger diameter rear tire with a Michelin bopper tire. This adds another 5mph top end. Dif temp ngk spark plug. Cone air filter. 21 mm carb. 68mph with 200 lb rider i take mine on the freeway no issues with MC license. Ive tried all other combos this worked best
You Should put A hpi inflammation On there that makes A huge diffrents On how the bike reacts als A combustion chamber cilinder head from ht Parts. For the best tuning parts you schooldag look On ht parts or ddl tuning. Love your vids ❤
So I I knew you could upgrade scooters but I never knew you could go this deep.. I bought my gf a scooter with a 70 kit. But now I found your page I need to build myself one of these vertical engine scoots… thanks a lot 😂
Why would you do that? It would be super expensive and complicated for no reason. He solely has to remove the mount on the exhaust side and weld in place a new bracket fitting the swing arm holes. That would look OEM and would cost less than 20 bucks.
Love the vid! But the restriction in the yasuni pipe are there for legal reason since most of these pipes are sold in europe where some countries require them to be restricted to 50cc an top speed of 45kph
in denmark we have 30 and 45kph so its restricted to 30 kph if you are under 18 and after that you can get a 45kph scooter. but its still illegal to put any aftermarket exhaust on even if it tops at 45kph :)
You should get a stage 6 overrange variator and clutch there is a all in one package. It dosent comprimise on the low speed you still get all the power for wheelies
great video, but how come you dont have any mopeds with innerroter ignitions, i have Italkit on my Minarelli Horizontal and it gives it so much more acceleration than stock.
i have on my derbi gp1, and will be putting one on the f12. i’ve heard a lot of bad about the ones for minarellis though, a lot of ppl have problems with them , the stock ignitions are actually pretty good on these motors
Anyone have a prebug for sale near Albuquerque NM or Birmingham Alabama during barber small bore?? Been looking for one for over a year and striking out 😢😢 , thanks for reading. Awesome video btw , never thought about porting the intake like that.
Hey guys I have a vertical Mineralli with the clean carb good petcock and fuel line I cannot get this thing to get any fuel to the cylinder. Previous owner ran the oil injection dry. I’m thinking the bad cylinder can’t pull in any fuel because of low compression? Any thoughts
I agree, the Stage6 system is a bit better than Polini, but it's a shame you put a Top Performance TPR Membrane on it. It has now been proven in several places that membranes with 2 large surfaces in total atomize better in the top area, Remember that it is very difficult to notice the difference between two tuning membranes, especially when you have two types as in your video.. A little advice that I know works, make sure you use 0.30mm carbon membrane plates, also cut a defective membrane plate over so that half is as big as before, and mount it on top of your membrane plates that wiggle. you do this on both sides, about 1cm This means that your membrane plates open and close much, much faster and, not least, every time the plates close, they close 100% tightly ALL THE TIME, and the atomization is much better. I myself use this method on my Yamaha Aerox with a membrane similar to the one you use in the video.
Lol let my buddy that rides a yamaha rd350 ride my prebug after I put stage six intake he was shaking his head going this thing stupid lol I told him to lean forward lol
Do you need a certain license over there to be allowed to ride a moped? And up until how many cc’s are you allowed to ride with ur license? Cuz if possible you should buy a gilera runner 125 or 180cc, they’re crazy bikes
I got a polini corsa for my minarelli vertical i tried fitting a yasuni r or z on it with a 17.5 dell carb but the bike didnt show any power or speed i didnt change the vario or clutch and i dont know why it wouldnt drive normal maybe bcs it stil have an air box instead of a filter
Using products for something other than what it's designed for. Real bright. Wheelies on a scooter. Gravity & pavement. It's all that matters. Enjoy the hospital visits.
MERCH available 🫶🏻 mopboyz.com/
Great video! Heres an easy way to measure your wheel for your speedo:
Use some chalk to draw a line from your tyre onto the floor. Then roll your scoot forward until the chalk is perpendicular to the floor again and draw a second line onto the floor. Now use a tape measure to measure the distance between the two chalk marks on the floor.
If there only was some kind of formula that let's you calculate the circumference of a circle using nothing but the radius or even the diameter... Any thoughts, Archimedes of Syracuse???
@@thomask.8533if only
It sounds so good with that intake
straight ripper
Love you videos dude! What’s the story on the VW bug? That thing looks super sick
had that since i was 15! i have some old vids on the channel, need to bring her back to life
@@MOPBOYZ dude you should definitely do a video on bringing her back that would be a sick video! Thanks for being the best scooter channel on UA-cam, I just bought a 150cc gy6 to start messing around on and give my 81 Honda a break 😂. Thanks dude
@@MOPBOYZ bring her back to life please
On a carbed zuma the best mods - front pulley take nut off, remove washer, put nut back on without, this adds 5mph top end. Blue clutch rollers and springs. 70cc head, not 100cc trust me. Variator. Leave front pully alone. Kevlar belt. Leo vince zx exhaust baffles removed and exhaust head drilled open. Larger rear spring/shock to accommodate the larger diameter rear tire with a Michelin bopper tire. This adds another 5mph top end. Dif temp ngk spark plug. Cone air filter. 21 mm carb. 68mph with 200 lb rider i take mine on the freeway no issues with MC license. Ive tried all other combos this worked best
Always a great vid. I like how it sounds. Rock on 🤘 old man mop.
thanks my dude !
You Should put A hpi inflammation On there that makes A huge diffrents On how the bike reacts als A combustion chamber cilinder head from ht Parts. For the best tuning parts you schooldag look On ht parts or ddl tuning. Love your vids ❤
I had 50cc with the 70 bore kit in it and it went 75mph .it blew up not long after
Doubt it
Nice builds with the bws 100.Do you need a front fork of an aerox 100 to ride the aerox 100 wheels?Or on the bws original suspension!?
So I I knew you could upgrade scooters but I never knew you could go this deep.. I bought my gf a scooter with a 70 kit. But now I found your page I need to build myself one of these vertical engine scoots… thanks a lot 😂
horizontal way better!
@@mikkel4961 the one I have is an 08 goes pretty good.. I thought all the scooter guys likes the pre bug ones for wheelie scooters
Look into getting that arm 3d printed but with a yasuni exhaust mount.. Can 3D print metal now.
Why would you do that? It would be super expensive and complicated for no reason. He solely has to remove the mount on the exhaust side and weld in place a new bracket fitting the swing arm holes. That would look OEM and would cost less than 20 bucks.
You are federal with that piece 🤙🏾 one of a kind come on man you him🔥
Great video used a psn tubing one on piaggio cases as they snap alot on tuned 172/183 2t
Looking to get me a Zuma rn because of you 😂😂
You can't go by your speedometer; use your smart phone's GPS. Mopeds usually read higher --not lower.
Love the vid! But the restriction in the yasuni pipe are there for legal reason since most of these pipes are sold in europe where some countries require them to be restricted to 50cc an top speed of 45kph
in denmark we have 30 and 45kph so its restricted to 30 kph if you are under 18 and after that you can get a 45kph scooter. but its still illegal to put any aftermarket exhaust on even if it tops at 45kph :)
who drive's legal? lol thats boring go hard or go home
@@snipezpro9554 not many rides legally 🤙
You have a unique taste in cars and scooters bro 👍🏽
You should get a stage 6 overrange variator and clutch there is a all in one package. It dosent comprimise on the low speed you still get all the power for wheelies
i had one on my other prebug i didn’t like the overrange for this bike i put it on my f12 it’s great on there
okay but what didnt you like ab it?
@@MOPBOYZ
Yamaha bws is so rare in Sweden we have like 2 on marketplace and one is in pieces. You have like 5 in your garage.
Hey Trever do you think the torsen arm for horizontal would fit the f12 ? And if yes is the case for the f12 the same as a bugeye ?
it depends , i think the disc rear f12 is different but drum is same as bugeye so it should work if you have drum
you can still get any part here in the netherlands even the polini brace
great video, but how come you dont have any mopeds with innerroter ignitions, i have Italkit on my Minarelli Horizontal and it gives it so much more acceleration than stock.
i have on my derbi gp1, and will be putting one on the f12. i’ve heard a lot of bad about the ones for minarellis though, a lot of ppl have problems with them , the stock ignitions are actually pretty good on these motors
@@MOPBOYZ depends on which ignition you get. if availible in america, the PVL ignitions are a really good pick. (e.g stage6)
Did you run the scooter before you started mod on restricter and re packing
Anyone have a prebug for sale near Albuquerque NM or Birmingham Alabama during barber small bore?? Been looking for one for over a year and striking out 😢😢 , thanks for reading. Awesome video btw , never thought about porting the intake like that.
What do you think about running bigger then a 21mm carb on a full poloni build?
depends on the motor but for a minarelli they like smaller carbs, you can usually get away with a 19mm but 21 mm works too
@@MOPBOYZ also depends type of engine. aluminium or iron cast high or low rpm i know a pre bug hitting 17hp with athena 70cc kit 24mm carb
@@MOPBOYZwhats the best carb and parts for a piaggio zip?
those connections on stage6 intake is for boost bottle
boost bottles are proven to not work
Hey guys I have a vertical Mineralli with the clean carb good petcock and fuel line I cannot get this thing to get any fuel to the cylinder. Previous owner ran the oil injection dry. I’m thinking the bad cylinder can’t pull in any fuel because of low compression? Any thoughts
baby got power
great video, would you be able to help out with what would be the best mods to buy for my moped- peugeot speedfight 2 AC
Where can i get a aftermarket handlebar post
Cool videos ! Greetings from Germany ! All your modifications are illegal here 😅
Lets discuss the polini intake😊😊
The dog loves it
Do you know any good upgrades for a Sym fiddle 200i scooter?
Dude where did you g’et the polini torsen
I agree, the Stage6 system is a bit better than Polini, but it's a shame you put a Top Performance TPR Membrane on it. It has now been proven in several places that membranes with 2 large surfaces in total atomize better in the top area,
Remember that it is very difficult to notice the difference between two tuning membranes, especially when you have two types as in your video..
A little advice that I know works, make sure you use 0.30mm carbon membrane plates, also cut a defective membrane plate over so that half is as big as before, and mount it on top of your membrane plates that wiggle. you do this on both sides, about 1cm
This means that your membrane plates open and close much, much faster and, not least, every time the plates close, they close 100% tightly ALL THE TIME, and the atomization is much better. I myself use this method on my Yamaha Aerox with a membrane similar to the one you use in the video.
Lol let my buddy that rides a yamaha rd350 ride my prebug after I put stage six intake he was shaking his head going this thing stupid lol I told him to lean forward lol
Did I see a supercharger belt on that bug. Whatcha running in it
@@bobbybradford8301 2276cc with a b&m charger
Do you need a certain license over there to be allowed to ride a moped? And up until how many cc’s are you allowed to ride with ur license? Cuz if possible you should buy a gilera runner 125 or 180cc, they’re crazy bikes
they’re not in america , no special license to ride scooters here because they’re not popular in this country at all
U gotta have AM license
A 16yo could go out and buy a 1000cc bike if they wanted
@@mitchankrom3771 16 year olds are limited to 125cc
@@dovydas4036 I'm talking about America
Im scared to derestrict mine because ive heard if you go full throttle too long you may blow the motor on a 2 stroke😢
What should I do?
lol that is hilarious. whoever told you that was joking with you
I got a polini corsa for my minarelli vertical i tried fitting a yasuni r or z on it with a 17.5 dell carb but the bike didnt show any power or speed i didnt change the vario or clutch and i dont know why it wouldnt drive normal maybe bcs it stil have an air box instead of a filter
the 17.5 carb is small for a corsa
I have a Leo vince zx to my 70cc is it worth to buy a Yasuni r instead?
i’ve tried the zx i like yasuni more
I love Your dog
big fan!
sounds mint
What’s the setup?
how much does a zuma cost stock?
Hi, I have a 125 moped can I go from stock straight to stage six?
a 125cc is a a1 not a moped anymore
What cylinder? My zuma turns really really hot in the Summer. IT has much loss of Performance is it normal?
you could have an air leak. this is a polini corsa
@@MOPBOYZ you mean in the plastics of the cylinder?
it could be an air leak anywhere in your engine
why dont u buy a better exhaust like c10 or c16 instead of R?
i’m not loooking for a top end power bike, it’s a stunt bike so mid range, R is perfect for that setup
@@MOPBOYZ i see
Where did you get the black domino grips from?
they’re odi
@@MOPBOYZ you got only the grips or the whole set with it cuz i cant find where to order only the grips
Would’t a yazuni c10 pipe fit better
c10 fits the same , all the same mounting
@@MOPBOYZ no i mean size vise
potato salad broccoli salad 11:17
Is the restricter out of the silencer?
i showed it in the vid lol
Oh sorry bro i dont see it 😂
torseen wd is still forsale
how much ?
Dellorto is al lot better then polini carbs
@ 10:22 That's a bracket from the puch seat ain't it?lol
yup lol
@@MOPBOYZ I know my puch parts! nice fix 👍
this some good shi
Danm brother save a Zuma for me.
with stock crank?
malossi rhq crank
i want my scooter like thaaaat
Test Yamaha slider🙏
they’re not in america
Your dog wants to play
my stock 50cc peugeot goes 80kmh/50mph that goes only like 100kmh/60mph
yes , top speed really depends on gearing/cvt set up
Theo von playing too…
I got a Yamaha jog 101cc ripping wheelies peep me
take your dog with you for a ride, but don't wheely
Stage 6 parts are weak lol especially the bearings and seals
i only use polini for bearings an seals . s6 for anything cvt and intake only
@@MOPBOYZ good shout bro
Using products for something other than what it's designed for.
Real bright. Wheelies on a scooter.
Gravity & pavement. It's all that matters. Enjoy the hospital visits.
you sound miserable
$ 5,000 toys.
Just like your sex toy collection
more like $500
@@jami2580 sure it's more than that for those boxes today.
@jami2580 with all the mods that it has, it would be around $5000
💯🔥🚀🛵🤙👌😉
Is that the Sedici Viaggio Parlare? I have that same helmet lol