I purchased the transmission from an authorized Jasper dealer summer of 2017 in Yorktown, VA. The original transmission was slipping in reverse after 87k miles. I paid 5800 for Jasper replacement. This transmission was an upgrade to the standard. The authorized dealer completely flushed the cooler and replaced all the transmission lines because the original lines did not connect to new transmission. The transmission seem to do fine. The transmission failed at 89k while towing a 5000 lb trailer with the Dodge 2500 diesel. The transmission blew a seal and all the fluid was pumped out unknown while traveling at highway speed. The noise was the clue that something was very wrong. Pulled into a Food Lion parking lot and then noticed my trailer was covered in transmission fluid. I contacted Jasper. I was told they would reimburse 70 / hr labor rate, which would not cover the Dodge dealer ship labor rate. I was 6 hours from home with a two-year-old Airstream covered in transmission fluid. Jasper hinted the failure was probably due to a bad cooler or plugged ATX lines. The reasoning was unacceptable considering the work was performed by authorized Jasper installer who told me they flushed the cooler and replaced all ATX lines. The original receipt had the new lines and the cooler flush annotated. Jasper could not give me a time to repair and told me the old ATX one had to be shipped back before they could honor the repairs. With my wife in tears, I elected to trade in a nice truck to purchase a new. The way Jasper handles the warranty left me sick to my stomach and out $5800 for a 6-7 month old Jasper re-manufactured transmission with less than 2000 miles. The transmission should have never leaked fluid the way it did assuming all seals were replaced with new. I suspect the replacement parts used were not of original quality, which lead to the premature failure. At a minimum Jasper should honor some type of refund. The warranty could of been handled differently. They essentially leave you hanging and provide you with no information on how long it will take or what action you need to do to restore vehicle operation. We were left stranded. After spending 5800 dollars on this very bad deal I could not in good conscious spend more money on hotel, restaurants, and higher cost for dodge to perform the work. Jasper provided no information on how long it would take to ship and receive a replacement transmission.
No they don’t. Quality in the last 5 years has gone to $hit! They don’t have anything in stock and can’t find enough people to actually employee in their hokey doke town of Jasper Indiana.
I bought a rebuilt 300- 6 cylinder for my 1981 F-100. It was a great engine! The price was right and they came and got my core at my home. The engine was still running great. When I donated it to a good cause. It has 60,000 miles on it with no troubles. Still wish I had it. Shawn
Hi Raised in San Bernardino and wish I had seen your interview before I let them put a Jasper junk engine in my motor home. I am on my 4th engine from Jasper. First one lasted just over 100 miles when it through a balance shaft through the valve cover. Next one was so bad we didn't even put it in, Third just failed at 3200 miles. Metal all through the engine and will have to put a 4th in, Just getting the runaround at Jasper but I am $24,000 into a $60,00 motor but couldn 't sell it the way it is.......Just letting you know if you can, tell anyone you can, not buy a Jasper engine. It is a long story but I'll keep this short......
I had a Jasper transmission put in my 2005 Ford E-250 van with 5.4 liter engine back in 2011. I still run this vehicle which has about 730,000 miles on the original engine and about 280,000 on the Jasper tranny. The only issue I had was during the original warranty period and needed a bit of work on a sensor. Otherwise, the tranny is still working fine. Most of my miles were over-the road, but I would recommend this company based on my experiences.
Jasper pays for these videos. The fact is they cut every corner possible. We got a Ford 4.6 from Jasper, they spray painted the inside of valve covers, right over sludge. That was the last straw after several failures. Get a factory replacement, or have a quality machine shop rebuild yours. The wait time from machine shop is better than dealing with warranty process on junk that WILL fail.
Simply not true. Been doing business with them for 20 years.I live in INDY. I went down and took a tour. They do good work and lot of hardworking men and women with no corners cut. Never had a issue except 1 time in TWENTY YEARS. Bad motors and stuff happen. It’s part of the business
I’m in a similar predicament and was thinking of opting for getting an engine from Jasper but now I’m unsure, if you could enlighten me where could I get a factory replacement for an old Ford Ranger if that’s possible?
I love how he talked about book time. Book time is a recommendation only. Book doesn't know the condition of vehicle, of shop, or the technition's ability. I never work for boom time. But I use the book to reference only. Then I decide on my own time. Which is based on my experience, and vehicle condition.
Steve P. I 100% agree. I can't tell you how many times the book time has been over 10 hours and I get it done way before then sometimes way after. It all depends on the car and the mechanic like you stated.
Fuck the book time, how about actual time. Too many of these shops will be more than happy to charge the book time even if they finish the job a few hrs early. But if the job goes over the book time, they'll charge for that. Glad I'm able to do most of my own work.
I've heard more bad things about jasper than good. The vehicle I have now has a jasper transmission, which is the 2nd one because the 1st jasper trans went out before 10k miles. Hoping this 2nd one last longer than that, it has about 8k on it now, we'll see.
Rick, tell her Bundy sent you. (540) 830-0286 ask for Heather. They offer a great warranty and good remanufacturing. Let Heather know Bundy sent you, she's the best. Hope this helps. Let me know what happens.
I'm about to put a Jasper reman transmission on my '11 Silverado 1500 RWD. Any words or advice? It'll cost me $4,324 OTD. Less than what everyone here says but its probably becauase it is only RWD. My checklist for the mechanic installing it so far are: Make sure the seals are replaced with OEM quality and make sure warranty is completed by the mechanic shop I worked with.
Dad is a Jasper dealer and no problems with their warranty yet.They send a replacement at no charge.Had this with two 5.7 hemi engines with the MDS in a 2008 and covered both of them.One had bad brand new Chrysler lifters from the factory.The other,they overtorqued the rocker arm assembly bolts.The factory remans,they are outsourced done by an outside machine shop with zero upgrades done.Jasper does the upgrades fixing the factory flaws.Have rebuilt a GM reman 4L80E before,went bad.GM puts the faulty parts back in their remans.
Mr. Frederick, Ignore the Bundy guy. He must work for a parts store or an online engine company. He has the business mentality of a title loans shark. Giving people false hope and spreading his manure everywhere.
I have a trailblazer ss with a jasper engine and transmissions truck runs better then the factory parts and i beat the crap out of it when im on the highway no issues and i love it thank you jasper
Jasper is awesome have a 91 Jeep Wrangler transmission went out the last day of the warranty beautiful I'm a private owner those guys are number one they stand behind what they sell 100%
If it was replaced under warranty, the “replacement” transmission’s warranty ended on the last day of the warranty. The warranty does not renew for another 3 years on that replacement transmission. Did you know that?
They used to be good but it seems like after 2015 that the quality of their remanufactured products started slipping and mechanics in my area started refusing any Jasper installs or warranty work because of the sudden high failure rate of their products and Jasper was all of a sudden finding ways to deny claims even when it was evident that the failure was on their end. One mechanic compared them to that Car Shield warranty company, said he put a sign up saying he will not do any warranty work on Jasper Products.
Are they any good? I'm on Jasper engine #3 in 358 days. Jasper seems to be having some serious quality control issues. If it wasn't for their warranty, I'd be broke.
The first Jasper engine knocked like an old diesel, kept getting louder the longer I drove it. The second engine (which replaced the knocker), had coolant in the oil. On the third Jasper engine in less than a year. I wouldn't wish this miserable experience onto anyone. And has anyone from Jasper ever contacted me over this? Nope. They apparently couldn't care less.
When you spend this much money on marketing and begging shops to praise your product, that tells me all I need to know. Build a damn good quality product and you will never have to beg installers to promote it. The work will speak for itself.
@@bundysgarage it doesn’t take much digging to see the number of shops that now refuse to install these engines. Marketing a mediocre product is always cheaper than retooling a factory and teaching workers how to be true machinist and improving quality.
Who is this Bundy guy? Seems he was baiting the shop guy. Jasper is great and always does good for my customers and myself. I wish this hack job would come to my shop. I'd hate to see a grown man cry.
So wtf everyone in California says jasper is good , all the shops I go here in California says jasper is the best , but then I get on UA-cam and see all you guys says jasper sucks
J 2 comments about Jasper products is i know 2 brothers that own and operate a auto repair shop and towing company they use Jasper products and they have always told me that the motors do have problems but the company backs them up i bought a boat from a freind that had a Jasper motor installed by my freinds mechanics and marina and it always had a weird noise to it plus never felt right to me and ive owned 17 or 18 boats in my life i also knew another boater that tried having Jasper motors put in and he ran the boat the motors Blew up again Jasper did stand by their product nut my buddy lost the entire boating season because that boat was in the shop having new engines put in it 2 or 3 times that year the irony was that the owner actually owns and operates his own boat and Yacht sales business and the boat with the Jaspe moto issues was the one he used as his commuting boat every day to go to andfrom his office and home ? BTW the actuall boat was a Chris Craft Stinger a sort of Go Fast off shore racing boat style and his engines were not Hot rod dead or altered in any manners they were simply big block Chevy motors turning Mercruiser outdrives , my boat i refered to had a Chevy V6 motor in it and was a small SeaRay as far as their marine division i know of not one person that has bragged about their products being fantastic And to me a Florida guy that says a bunch
In my opinion, the quality that they have been putting out has gone down hill in the past 5 - 7 years. They struggle to find a good workforce, they don't pay a whole lot, and if they do find someone who can build an engine or transmission, those people usually move up in the company. I'm trying to get an interview with a former employee, I'm really curious to see what her opinion is about their outfit in rural Indiana.
the problem is there seems to be no quality control ,test the motor and dyno them ,alot of these companies claim they do but they do not ,I by passed Jasper and Fraiser because of this and just bought a Powertrain Products motor and had it installed 2 days ago ,I may note that I had the mechanic replace everything outside the motor name it it was replaced ,well its ticking and we realized it seems to be a valve guide ,you may say well thats not so bad but with the warranty only paying $50 per hour to replace any internal parts your getting screwed ,I would have paid alot more money for the engine if it was dynoed and checked for any issues ,but thats a lie because something like that should have been caught before leaving the factory
For the title to say they suck I didnt hear very many negative things coming from this guy. your title is just click bait with no proven facts. Quit bashing a very well proven and accomplished company
Is this Austin Green? If it is, hope your doing well. Just do a quick Google search for “Jasper engines review” and you will see countless complaints about Jasper and their piss poor product. Don’t just look at my video, just read all the bad reviews on Consumer Reports (www.consumeraffairs.com/automotive/jasper-engines-and-transmissions.html) then write back to me Austin and answer all those complaints. Also answer me this, why doesn’t Jasper respond back to any of the bad reviews they receive? That has always bewildered me. I’m always open to do a video, in response to my video, with someone from Jasper if they want too.
@@bundysgarage I'm not Austin Green. but let me explain this too you in simple terms. While yes I'm sure they trust their installers. But do you realize that we live in a world where there is no accountability? how easy is it for them to pass on their product to the installer only for the installer to mess something up and then in turn blame jasper engines. Which in turn makes Jasper look bad. It's much easier for the installer to look like the good guy because the customer can see them face to face while they throw dirt on top of jasper because they aren't there to defend themselves until the installer has already told their side and got told a million times "well its jasper's fault" and to your point about the negative reviews, if you go and read reviews on any major company all your gonna see is automated messages. If jasper had something to say about it, it was probably handled on the phone and not by a default comment on a youtube video or on BBB. I'm sure they accomplish more by telephone than through comments on a website.
H & A Transmissions, Rancho Cucamonga, California. Great Honda Transmission rebuilders. That’s where Jasper gets their transmissions from for the Honda V6 J Series platform.
Im on my 3rd Jasper engine, the 1st 2 engines failed within a year. I only had 6 days left on the warranty when the 2nd Jasper engine failed (head gasket). I just received my 3rd Jasper engine with zero warranty left, has the same hesitation when going up hills. I can honestly say Jasper engines are JUNK!!! Im very disappointed
Jasper quality has really gone down hill. They also have a small employment pool to draw upon, so hinders good talent. If you are anyone else are looking for an engine or transmission call 540.830.0286 and ask for Heather, tell her Bundy sent you. Go Powertain is a great company and have good success with it.
Jasper is absolute trash. Have a 2006 24v Cummins with a jasper (cost 10 GRAND) and in 15k here’s what’s failed: injector 1 and 4 (jasper reman), rear main seal leak, crank sensor failed, and some other small shit. Just ridiculous for a motor with 15k mikes.
Jasper is a large engine and transmission remanufacturer, since it sells hundreds/thousands there will be bad lots depending on parts and so forth. Ford, GM, Dodge, Toyota, BMW, and so forth have thousands of recalls every year, yet I have not heard the whiners here talk about.
Jasper engines and transmission are typically more expensive than the dealership, be that Ford, GM, Chrysler. Guess someone has to pay for party out in Jasper, IN.
@@bundysgarage Just one of my experiences with Jasper was with a reman DT444 from them. Put it in a flatbed 4700 series due to the old engine blowing a head gasket. Installed the jasper replacement and upon the first start up and warm up period it blew another head gasket, tore the engine down to find the head gaskets reused and sprayed down with a black gasket material. They warrantied the engine so we installed another engine and that one threw a rod 5 hours into use after break in. Nonstop problems with Jasper and some real shady remanufacturing processes.
They sure have gone down hill in the last couple of years. They use to do great work but now I hear bad story after bad story when it comes to Jasper. They re-use old parts out of engines that they believe they have tested throughly when they re-manufacture an engine or transmission. I have seen it with my own eyes or ask any Jasper representative.
@@mattmejia Please let us know what happens with your 4.6L. BE very interested to see how long it lasts for you. I have been talking to other shop owners and they say they have seen a huge decrease in quality from Jasper, and these are guys that are die hard Jasper fanatics
I purchased the transmission from an authorized Jasper dealer summer of 2017 in Yorktown, VA. The original transmission was slipping in reverse after 87k miles. I paid 5800 for Jasper replacement. This transmission was an upgrade to the standard. The authorized dealer completely flushed the cooler and replaced all the transmission lines because the original lines did not connect to new transmission. The transmission seem to do fine. The transmission failed at 89k while towing a 5000 lb trailer with the Dodge 2500 diesel. The transmission blew a seal and all the fluid was pumped out unknown while traveling at highway speed. The noise was the clue that something was very wrong. Pulled into a Food Lion parking lot and then noticed my trailer was covered in transmission fluid. I contacted Jasper.
I was told they would reimburse 70 / hr labor rate, which would not cover the Dodge dealer ship labor rate. I was 6 hours from home with a two-year-old Airstream covered in transmission fluid. Jasper hinted the failure was probably due to a bad cooler or plugged ATX lines. The reasoning was unacceptable considering the work was performed by authorized Jasper installer who told me they flushed the cooler and replaced all ATX lines. The original receipt had the new lines and the cooler flush annotated. Jasper could not give me a time to repair and told me the old ATX one had to be shipped back before they could honor the repairs. With my wife in tears, I elected to trade in a nice truck to purchase a new.
The way Jasper handles the warranty left me sick to my stomach and out $5800 for a 6-7 month old Jasper re-manufactured transmission with less than 2000 miles. The transmission should have never leaked fluid the way it did assuming all seals were replaced with new. I suspect the replacement parts used were not of original quality, which lead to the premature failure. At a minimum Jasper should honor some type of refund. The warranty could of been handled differently. They essentially leave you hanging and provide you with no information on how long it will take or what action you need to do to restore vehicle operation. We were left stranded. After spending 5800 dollars on this very bad deal I could not in good conscious spend more money on hotel, restaurants, and higher cost for dodge to perform the work. Jasper provided no information on how long it would take to ship and receive a replacement transmission.
So it’s safe to say you will never buy another Jasper product again nor recommend them to your friends or family?
If you had gotten the transmission from a Dodge dealership they would of taken care of you at any dealership in the US.
Nope f u
Jasper does great work. Been dealing for 20 years. Never had one issue. Seems like the issue was probably you.
No they don’t. Quality in the last 5 years has gone to $hit! They don’t have anything in stock and can’t find enough people to actually employee in their hokey doke town of Jasper Indiana.
I bought a rebuilt 300- 6 cylinder for my 1981 F-100. It was a great engine! The price was right and they came and got my core at my home. The engine was still running great. When I donated it to a good cause. It has 60,000 miles on it with no troubles. Still wish I had it. Shawn
Hi Raised in San Bernardino and wish I had seen your interview before I let them put a Jasper junk engine in my motor home. I am on my 4th engine from Jasper. First one lasted just over 100 miles when it through a balance shaft through the valve cover. Next one was so bad we didn't even put it in, Third just failed at 3200 miles. Metal all through the engine and will have to put a 4th in, Just getting the runaround at Jasper but I am $24,000 into a $60,00 motor but couldn
't sell it the way it is.......Just letting you know if you can, tell anyone you can, not buy a Jasper engine. It is a long story but I'll keep this short......
What part of San Bernardino. I grew up in Highland and Redlands.
I had a Jasper transmission put in my 2005 Ford E-250 van with 5.4 liter engine back in 2011. I still run this vehicle which has about 730,000 miles on the original engine and about 280,000 on the Jasper tranny. The only issue I had was during the original warranty period and needed a bit of work on a sensor. Otherwise, the tranny is still working fine. Most of my miles were over-the road, but I would recommend this company based on my experiences.
Glad you had good luck with it.
Man that's 200 miles aday everyday for 14 yrs.....bullshit
Me too. Amazing company
Jasper pays for these videos. The fact is they cut every corner possible. We got a Ford 4.6 from Jasper, they spray painted the inside of valve covers, right over sludge. That was the last straw after several failures. Get a factory replacement, or have a quality machine shop rebuild yours. The wait time from machine shop is better than dealing with warranty process on junk that WILL fail.
Simply not true. Been doing business with them for 20 years.I live in INDY. I went down and took a tour. They do good work and lot of hardworking men and women with no corners cut. Never had a issue except 1 time in TWENTY YEARS. Bad motors and stuff happen. It’s part of the business
I’m in a similar predicament and was thinking of opting for getting an engine from Jasper but now I’m unsure, if you could enlighten me where could I get a factory replacement for an old Ford Ranger if that’s possible?
@@deathuponusalll Get a used low milage one online. Your mechanic will know where to find one.
@@TruthSeeker1988 thanks! I was researching more and found one place in particular that warranties me for up to 7 years!
Wrong !!! Jasper 4.6 & 5.4 Engines Never Come With Valve Covers, Your Problem Is With Installer !
I love how he talked about book time. Book time is a recommendation only. Book doesn't know the condition of vehicle, of shop, or the technition's ability. I never work for boom time. But I use the book to reference only. Then I decide on my own time. Which is based on my experience, and vehicle condition.
Great point
Steve P. I 100% agree. I can't tell you how many times the book time has been over 10 hours and I get it done way before then sometimes way after. It all depends on the car and the mechanic like you stated.
Fuck the book time, how about actual time. Too many of these shops will be more than happy to charge the book time even if they finish the job a few hrs early. But if the job goes over the book time, they'll charge for that. Glad I'm able to do most of my own work.
I worked for a man one time in a rv repair shop..and he went 100% on book time...this man couldn't pour pee out of a boot..but could tell you how..lol
I've heard more bad things about jasper than good. The vehicle I have now has a jasper transmission, which is the 2nd one because the 1st jasper trans went out before 10k miles. Hoping this 2nd one last longer than that, it has about 8k on it now, we'll see.
Did anything happen to it ?
@@abetorres652 This was 3 years ago, the vehicle finally gave up the ghost at 346,000 miles.
@@Blueknight1960 they do great work
I see you commenting on all these bad comments people have left about Jasper. How long have you worked for them?
@@bundysgarage @kiss must have gotten fired by Bud Lite and Jasper hired him.
I agree 100% with you about book time..book time doesn't mention rust. And up north vehicle's..so a 1.5 hrs job can turn into 8 hrs.
I HATE rust 😡
Hi bundy what reman company do you recommend as far as reliable.
Rick, tell her Bundy sent you. (540) 830-0286 ask for Heather. They offer a great warranty and good remanufacturing. Let Heather know Bundy sent you, she's the best. Hope this helps. Let me know what happens.
I'm about to put a Jasper reman transmission on my '11 Silverado 1500 RWD.
Any words or advice? It'll cost me $4,324 OTD. Less than what everyone here says but its probably becauase it is only RWD.
My checklist for the mechanic installing it so far are:
Make sure the seals are replaced with OEM quality and make sure warranty is completed by the mechanic shop I worked with.
They do great work and easy and nice to deal with
How’s it holding up so far?
yes, How is it doing?
Dad is a Jasper dealer and no problems with their warranty yet.They send a replacement at no charge.Had this with two 5.7 hemi engines with the MDS in a 2008 and covered both of them.One had bad brand new Chrysler lifters from the factory.The other,they overtorqued the rocker arm assembly bolts.The factory remans,they are outsourced done by an outside machine shop with zero upgrades done.Jasper does the upgrades fixing the factory flaws.Have rebuilt a GM reman 4L80E before,went bad.GM puts the faulty parts back in their remans.
Are you hired by Jasper to post this same comment on the all videos talking about the piss poor quality they have?
Mr. Frederick, Ignore the Bundy guy. He must work for a parts store or an online engine company. He has the business mentality of a title loans shark. Giving people false hope and spreading his manure everywhere.
I have a trailblazer ss with a jasper engine and transmissions truck runs better then the factory parts and i beat the crap out of it when im on the highway no issues and i love it thank you jasper
How long/miles have you had the engine in the car?
@@bundysgarage its been about 4 years now probably about 15.000 miles i put in it so far
Jasper is awesome have a 91 Jeep Wrangler transmission went out the last day of the warranty beautiful I'm a private owner those guys are number one they stand behind what they sell 100%
If it was replaced under warranty, the “replacement” transmission’s warranty ended on the last day of the warranty. The warranty does not renew for another 3 years on that replacement transmission. Did you know that?
They used to be good but it seems like after 2015 that the quality of their remanufactured products started slipping and mechanics in my area started refusing any Jasper installs or warranty work because of the sudden high failure rate of their products and Jasper was all of a sudden finding ways to deny claims even when it was evident that the failure was on their end. One mechanic compared them to that Car Shield warranty company, said he put a sign up saying he will not do any warranty work on Jasper Products.
Having a lot of knowleadge with many remanufacturers over many years, Jasper is hands down by far the best
Danny Watkins than why is there 160 complaints on bbb about jasper???
Danny Watkins as the other asked. Why such poor reviews? I have to get a rebuilt transmission and sure need a recommendation
Jordan Wheat because they sell many thousands a year ???
@@sccarguy8242 yea i would probably agree here 100% satisfaction is just not viable. how much of it is installation error?
Danny Watkins works for Japser so of course he’s going to say they are the best. He doesn’t want to piss off his overlords!
You are 100% correct the warranty does not renew for another 3 years
So out of how many did you have zero issues with??
I think Jasper the best bang for your buck in factory replacement engines or transmissions,
Are they any good? I'm on Jasper engine #3 in 358 days. Jasper seems to be having some serious quality control issues. If it wasn't for their warranty, I'd be broke.
That’s a bummer. 3 engines less than a year! What are the details behind that?
The first Jasper engine knocked like an old diesel, kept getting louder the longer I drove it. The second engine (which replaced the knocker), had coolant in the oil. On the third Jasper engine in less than a year. I wouldn't wish this miserable experience onto anyone. And has anyone from Jasper ever contacted me over this? Nope. They apparently couldn't care less.
They have a lot of bad reviews online. Just Google Jasper Engines review
@@bundysgarage so who would you recommend for a 2000 dodge durango 4.7 motor? I want to avoid jasper
Go read the online reviews. Please
When you spend this much money on marketing and begging shops to praise your product, that tells me all I need to know.
Build a damn good quality product and you will never have to beg installers to promote it. The work will speak for itself.
Did you have a Jasper engine or transmission blow up on you? Did they make you watch videos on their ipad's?
@@bundysgarage it doesn’t take much digging to see the number of shops that now refuse to install these engines. Marketing a mediocre product is always cheaper than retooling a factory and teaching workers how to be true machinist and improving quality.
Who is this Bundy guy? Seems he was baiting the shop guy. Jasper is great and always does good for my customers and myself. I wish this hack job would come to my shop. I'd hate to see a grown man cry.
Better options? Can you clarify?
Buy reman from GM directly. 3 year 36k warranty or 3yr 100k if installed at the dealership.
So wtf everyone in California says jasper is good , all the shops I go here in California says jasper is the best , but then I get on UA-cam and see all you guys says jasper sucks
J 2 comments about Jasper products is i know 2 brothers that own and operate a auto repair shop and towing company they use Jasper products and they have always told me that the motors do have problems but the company backs them up i bought a boat from a freind that had a Jasper motor installed by my freinds mechanics and marina and it always had a weird noise to it plus never felt right to me and ive owned 17 or 18 boats in my life i also knew another boater that tried having Jasper motors put in and he ran the boat the motors Blew up again Jasper did stand by their product nut my buddy lost the entire boating season because that boat was in the shop having new engines put in it 2 or 3 times that year the irony was that the owner actually owns and operates his own boat and Yacht sales business and the boat with the Jaspe moto issues was the one he used as his commuting boat every day to go to andfrom his office and home ? BTW the actuall boat was a Chris Craft Stinger a sort of Go Fast off shore racing boat style and his engines were not Hot rod dead or altered in any manners they were simply big block Chevy motors turning Mercruiser outdrives , my boat i refered to had a Chevy V6 motor in it and was a small SeaRay as far as their marine division i know of not one person that has bragged about their products being fantastic And to me a Florida guy that says a bunch
In my opinion, the quality that they have been putting out has gone down hill in the past 5 - 7 years. They struggle to find a good workforce, they don't pay a whole lot, and if they do find someone who can build an engine or transmission, those people usually move up in the company. I'm trying to get an interview with a former employee, I'm really curious to see what her opinion is about their outfit in rural Indiana.
U sound like u work for Jasper.....
Nope don’t work for Jasper. Just heard bad thing about them.
Jasper engines are fine overall. But damn, never ever buy a remanufactured transmission ever. Always buy a brand new transmission if you can.
the problem is there seems to be no quality control ,test the motor and dyno them ,alot of these companies claim they do but they do not ,I by passed Jasper and Fraiser because of this and just bought a Powertrain Products motor and had it installed 2 days ago ,I may note that I had the mechanic replace everything outside the motor name it it was replaced ,well its ticking and we realized it seems to be a valve guide ,you may say well thats not so bad but with the warranty only paying $50 per hour to replace any internal parts your getting screwed ,I would have paid alot more money for the engine if it was dynoed and checked for any issues ,but thats a lie because something like that should have been caught before leaving the factory
For the title to say they suck I didnt hear very many negative things coming from this guy. your title is just click bait with no proven facts. Quit bashing a very well proven and accomplished company
Is this Austin Green? If it is, hope your doing well. Just do a quick Google search for “Jasper engines review” and you will see countless complaints about Jasper and their piss poor product. Don’t just look at my video, just read all the bad reviews on Consumer Reports (www.consumeraffairs.com/automotive/jasper-engines-and-transmissions.html) then write back to me Austin and answer all those complaints. Also answer me this, why doesn’t Jasper respond back to any of the bad reviews they receive? That has always bewildered me. I’m always open to do a video, in response to my video, with someone from Jasper if they want too.
@@bundysgarage I'm not Austin Green. but let me explain this too you in simple terms. While yes I'm sure they trust their installers. But do you realize that we live in a world where there is no accountability? how easy is it for them to pass on their product to the installer only for the installer to mess something up and then in turn blame jasper engines. Which in turn makes Jasper look bad. It's much easier for the installer to look like the good guy because the customer can see them face to face while they throw dirt on top of jasper because they aren't there to defend themselves until the installer has already told their side and got told a million times "well its jasper's fault" and to your point about the negative reviews, if you go and read reviews on any major company all your gonna see is automated messages. If jasper had something to say about it, it was probably handled on the phone and not by a default comment on a youtube video or on BBB. I'm sure they accomplish more by telephone than through comments on a website.
@@xxnatas69xx what engine are you speaking of? and how long ago did you buy it?
Interesting, I got a Jasper E4OD in a rig I recently bought. I don't trust it yet, it has some issues.
Who would you recommend? Need to replace Honda Odyssey 2006 transmission
H & A Transmissions, Rancho Cucamonga, California. Great Honda Transmission rebuilders. That’s where Jasper gets their transmissions from for the Honda V6 J Series platform.
Good morning I have a 2004 mercury grand marquis it gives a cold start in the morning when temperature is low what you think can cause it
Lots of things. Do you have any codes? Is the check engine light on?
Yes for the fuel driver module
I’ve heard nothing but horrible things about them
What was your experience with Jasper?
BundysGarage just go online and you’ll see tons of complaints
Yeah I’ve heard real horror stories about their engines and transmissions.
That would be a new transmission the next day send me a check 2 weeks later for labor plus fluids
What about street smart transmissions?
I have never heard of them. Where are they out of?
BundysGarage tampa Florida
Service it it's better then original drive like old man
You look like John Quinones from ABC's What Would You Do
You are the first person in my life to tell me that.
Im on my 3rd Jasper engine, the 1st 2 engines failed within a year. I only had 6 days left on the warranty when the 2nd Jasper engine failed (head gasket). I just received my 3rd Jasper engine with zero warranty left, has the same hesitation when going up hills. I can honestly say Jasper engines are JUNK!!! Im very disappointed
Jasper quality has really gone down hill. They also have a small employment pool to draw upon, so hinders good talent. If you are anyone else are looking for an engine or transmission call 540.830.0286 and ask for Heather, tell her Bundy sent you. Go Powertain is a great company and have good success with it.
I don't like straighten crankshaft
That mustache is awesome!
Jasper is absolute trash. Have a 2006 24v Cummins with a jasper (cost 10 GRAND) and in 15k here’s what’s failed: injector 1 and 4 (jasper reman), rear main seal leak, crank sensor failed, and some other small shit. Just ridiculous for a motor with 15k mikes.
Just bought a 6.0 L76
Why have I never heard one good thing about Jasper in 20 years
/
Jasper is a large engine and transmission remanufacturer, since it sells hundreds/thousands there will be bad lots depending on parts and so forth. Ford, GM, Dodge, Toyota, BMW, and so forth have thousands of recalls every year, yet I have not heard the whiners here talk about.
I’m getting ready to replace the motor in my 08 Tahoe.I was thinking Jasper until I watched this but I’m glad you put this comment out.Good point.
i heard their engines are good for 100k miles, then you'll need a new one.
Very expensive I would compare to Fraser
Jasper engines and transmission are typically more expensive than the dealership, be that Ford, GM, Chrysler. Guess someone has to pay for party out in Jasper, IN.
I don't recommend to anyone buy any engine or transmission from jasper they don't sale good parts
Keep it up nice content
Thanks
Tip of the day run away from Jasper Engines!!
What was your experience with Jasper engines?
@@bundysgarage Just one of my experiences with Jasper was with a reman DT444 from them. Put it in a flatbed 4700 series due to the old engine blowing a head gasket. Installed the jasper replacement and upon the first start up and warm up period it blew another head gasket, tore the engine down to find the head gaskets reused and sprayed down with a black gasket material. They warrantied the engine so we installed another engine and that one threw a rod 5 hours into use after break in. Nonstop problems with Jasper and some real shady remanufacturing processes.
They sure have gone down hill in the last couple of years. They use to do great work but now I hear bad story after bad story when it comes to Jasper. They re-use old parts out of engines that they believe they have tested throughly when they re-manufacture an engine or transmission. I have seen it with my own eyes or ask any Jasper representative.
@@bundysgarage because all people do is complain.
They complain when they get ripped off by Jasper engines.
Nice script.
The worst place to work fore
What happened?
Did you get fired due to being illiterate?
That's because they have a bunch of Mexicans working there now! Quality sucks!
Probably the same as you John (Jon) Bundy. Got let go from Jasper for being a turd out in Cali. I was told about you. Get a life Chump.
The worst place to buy a engine or transmission high percentage bad parts bull shit place
Jasper engines and transfer cases are JUNK don't waste your time
Do you have a company you could recommend?
What kind of engine or transmission are you looking for?
Shit I just bought a refurbished 4.6l v8! Fuck! I'll update you 🤭
@@mattmejia Please let us know what happens with your 4.6L. BE very interested to see how long it lasts for you. I have been talking to other shop owners and they say they have seen a huge decrease in quality from Jasper, and these are guys that are die hard Jasper fanatics
matt mejia any update ?
Jasper junk
What was your experience with Jasper?
👍🏻👍🏻👍🏻👍🏻👍🏻