Yes, over a configuration file "AutoSet.txt" located on SD card (included). And No, no need to calibrate after changing params. Only when you replacing controller or rotor.
@@PMartianWill do comparison table soon. BB3 is different, caa be connected to motor permanently (or you set parameters over BB3 and then disconnect), can switch speed limits and settings during the ride, is waterproof and has a ASLS (Auto Set Low Speed) function, when each motor power on device will set low speed (legal speed), is powered from main battery. K1 Flash is to set parameters, also to upload firmware, needs to be powered externally over USB-C and after configuration needs to be disconnected.
Za 150e mozete odlokovat 5 ebajkov. Ak by ste mali iny motor (Bosch, Shimano, Brose) musite si kupit odblokovatko za 200e a mozete to mat iba na jednom bajku. Mozem vam dat zlavu 10% na K1 Flash. Ak chcete odblokovat iba jeden bike, je tam Light verzia za 110e
Ciao, i next days wait new ebike Alpek motor M510 Bafang, i want take K1 flasher my question is, is possible reading end save the original set up M510 so if i have problem i comback to original, example whit producor garantie
Yes, that is right. Every time you gonna change setup parameters of motor, current settings are saved in a file on SD card. So you can any time go back to original settings. There is one issue - not possible to read firmware file from Bafang motor and save. There is no routine defined in a motor to read firmware over CAN bus. :( So if you gonna have some special custom firmware in your motor and you reflash with some other, you wont be able to roll back to your original if you dont have it as a bin file. But this would occur also with original Besst programmer - also no option to read from motor and save firmware.
I check out K1 flash web more detail and I got it , I watch bosch speedbox 3 chip..the instruction very clear, detail and well info from A _ Z ..your no audio ..I did not know what going , if you can have voice will be nice, thanks any way
ciao i have question,bang motor M510 in set up is possible seting the initial pedal assistant 1 to 13, ask if in concorent motor same bosch dont have but only torque set up?
Yes, that was FC1.0 FC2.0 and M560 has this setting in degree. According my math 7.5 degree is one level in old measure. Dont speculate about this one, set it to 1 (or 10 degree). Dont know why anybody would set this higher for mtb - maybe just as a safety settings for city ebikes.
@@dado304 thank,now i use one kit bafang BBS02 next step i want mtb Alpek Runa whit bafang M510 or M560 for next year2024 end need your K1 for firmware
@@gianniandrini3915 Wait a while with M560. Bafang has some issues now. But M510 is good. Good pedalling behaviour. Only downside, it is making high pitch soubd at high rpm.
Hello. Throtle should be working up to 32kmh with FC2.0 - this is hardcoded with M510 FC2.0. And I guess M560 is with 45km/h hardcoded. FC2.0 is brand new controller and firmware. It support power adjustments and torque sensor sensitivity settings, acceleration, start-up angle - now we can talk about good assistance to pedalling. Has also some HW changes comparing to FC1.0 - better torque sensor, one way clutch, sealing. FC1.0 was quite faulty and did tend to overheat. But throttle is here working up to speed you set. And was peaking 830W.
thanks for answer,so if i take motor M510 our motor M560 dont have problem to use throttle original bafang only configure corect parameter in set up , ciao @@dado304
@@gianniandrini3915 Throttle is working out of box with Bafang motors (unless u have some custom firmware). You need a main cable 1T2 or 1T3 to plug also bafang throttle. As I said M510 FC2.0 is hardcoded to 32kmh on throttle. M560 I guess 45kmh. Have not yet tried, waiting for better revision of M560. ;)
Configuration Parameters are SET by changing the text and numbers? Do you have to Recalibrate motor after changing parameters?
Yes, over a configuration file "AutoSet.txt" located on SD card (included). And No, no need to calibrate after changing params. Only when you replacing controller or rotor.
@@dado304 thank you! What is the difference of the other box you sell that can be hidden on the bike compared to k1 flash?
@@PMartianWill do comparison table soon. BB3 is different, caa be connected to motor permanently (or you set parameters over BB3 and then disconnect), can switch speed limits and settings during the ride, is waterproof and has a ASLS (Auto Set Low Speed) function, when each motor power on device will set low speed (legal speed), is powered from main battery.
K1 Flash is to set parameters, also to upload firmware, needs to be powered externally over USB-C and after configuration needs to be disconnected.
Nemáte nějakej použitej třeba za polovičku 👀? Mě to přijde prostě drahý 😅😁
Za 150e mozete odlokovat 5 ebajkov. Ak by ste mali iny motor (Bosch, Shimano, Brose) musite si kupit odblokovatko za 200e a mozete to mat iba na jednom bajku.
Mozem vam dat zlavu 10% na K1 Flash.
Ak chcete odblokovat iba jeden bike, je tam Light verzia za 110e
Ciao, i next days wait new ebike Alpek motor M510 Bafang, i want take K1 flasher my question is, is possible reading end save the original set up M510 so if i have problem i comback to original, example whit producor garantie
Yes, that is right. Every time you gonna change setup parameters of motor, current settings are saved in a file on SD card. So you can any time go back to original settings.
There is one issue - not possible to read firmware file from Bafang motor and save. There is no routine defined in a motor to read firmware over CAN bus. :( So if you gonna have some special custom firmware in your motor and you reflash with some other, you wont be able to roll back to your original if you dont have it as a bin file. But this would occur also with original Besst programmer - also no option to read from motor and save firmware.
What will I be able to change with this controller and drive?
show step by step and what software pls,
Hello. What should I show? Ive tried to do it step by step. ;)
No software needed, you just edit txt file on SD card with any text editor - wordpad.
I check out K1 flash web more detail and I got it , I watch bosch speedbox 3 chip..the instruction very clear, detail and well info from A _ Z ..your no audio ..I did not know what going , if you can have voice will be nice,
thanks any way
@michaelgiang7433 I dont have voice for videos. Believe me. ;) Maybe next video with a voice.
ciao i have question,bang motor M510 in set up is possible seting the initial pedal assistant 1 to 13, ask if in concorent motor same bosch dont have but only torque set up?
Yes, that was FC1.0
FC2.0 and M560 has this setting in degree. According my math 7.5 degree is one level in old measure.
Dont speculate about this one, set it to 1 (or 10 degree). Dont know why anybody would set this higher for mtb - maybe just as a safety settings for city ebikes.
@@dado304 thank,now i use one kit bafang BBS02 next step i want mtb Alpek Runa whit bafang M510 or M560 for next year2024 end need your K1 for firmware
@@gianniandrini3915 Wait a while with M560. Bafang has some issues now.
But M510 is good. Good pedalling behaviour. Only downside, it is making high pitch soubd at high rpm.
ciao question abouth FC1.0 e Fc.2.0 motor M510 what is difference? i ask becouse need use throttle in off road use in FC 2.0 not work
Hello. Throtle should be working up to 32kmh with FC2.0 - this is hardcoded with M510 FC2.0. And I guess M560 is with 45km/h hardcoded.
FC2.0 is brand new controller and firmware. It support power adjustments and torque sensor sensitivity settings, acceleration, start-up angle - now we can talk about good assistance to pedalling. Has also some HW changes comparing to FC1.0 - better torque sensor, one way clutch, sealing.
FC1.0 was quite faulty and did tend to overheat. But throttle is here working up to speed you set. And was peaking 830W.
thanks for answer,so if i take motor M510 our motor M560 dont have problem to use throttle original bafang only configure corect parameter in set up , ciao @@dado304
@@gianniandrini3915 Throttle is working out of box with Bafang motors (unless u have some custom firmware). You need a main cable 1T2 or 1T3 to plug also bafang throttle. As I said M510 FC2.0 is hardcoded to 32kmh on throttle. M560 I guess 45kmh. Have not yet tried, waiting for better revision of M560. ;)
Can this be used on a rear hub G0900 with a S307 controller
Hello. Yes, S307 seems as original Bafang controller with CAN bus.