How to Replace Valve Cover Gasket 2002-06 Toyota Camry
Вставка
- Опубліковано 29 вер 2024
- Buy Now!
New Valve Cover Gasket Set from 1AAuto.com 1aau.to/ic/1AEG...
Valve covers will begin to leak oil when the seals eventually break down. A new valve cover gasket set will make sure the oil stays inside the engine where it belongs! This video shows you how to install a new set of valve cover gaskets on your 2002-06 Toyota Camry.
• Check here for more videos on the 2002-2006 Toyota Camry • Toyota Camry 2002-2006...
This process should be similar on the following vehicles:
2002 Toyota Camry
2003 Toyota Camry
2004 Toyota Camry
2005 Toyota Camry
2006 Toyota Camry
Tools you will need:
• 10mm Socket 1aau.to/op9/1AX...
• Needle nose pliers 1aau.to/ocY/1AX...
• Needle nose pliers 1aau.to/ocY/1AX...
• Socket Driver
• Torque Wrench 1aau.to/omF/1AX...
• Brake Parts Cleaner
• Paper Towels 1aau.to/ocZ/1AX...
• RTV
• Rubber Mallet 1aau.to/oag/1AX...
Subscribe: / @trq
Check out our playlist:
Toyota Camry 2002-2006 5th Generation: • Toyota Camry 2002-2006...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
I cannot wait to try this on my own and show my daughters that mommy can do car stuff, too! 😉 Your video makes it look so easy. Very helpful, indeed.
How did that work out for you lol
@@dontbeakaren6145 had to show her how to get a “good” deal on a new car instead
Nice presentation. A concise explanation that explains exactly what must be done.
About to do this right now. I do all my basic maintenance but this is first time actually cracking into part of the engine. Thanks man.
Well done . Very good video. I was wondering if you can use some spray tack on the upper side of the gasket?
This video is Gold thank you ❤ I did this for the first time in 30-40 minutes it was easy with your great help 🎉
center bolts are 10 ftlbs and outside is 8
Great video! Straight to the point and made it super easy. Thank you!
Yup excellent as always, got this done, saved me 200 bucks! 🎉
Thanks! Dealer wants $337 plus tax. I would have missed the RTV if you hadn’t pointed it out. Very nice video.
Ty so much!! Definitely using this video to change out the parts in my car
+Meli Detwiler Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ
Tnx very well done! Question- Isn’t it needed to place RTV all around the gasket upon replacement? What kind of liquid did u use to clean the valve cover, was it gasoline?
Since the cover is off, I suggest checking the chain for looseness. Plus the valve cam clearance.
Would not adding rtv sealant cause a misfire? I just did this job and now I have a bad misfire😢
This is very well done. Thank you for this.
Thank you got mine changed using this today!
Good video, thank you!!! What torque wrench did you have? The link you provided did not go the one you used.
Great video thanks for uploading
Great video, man!!! Thanks!
Just fyi, if ur gna bottom the bolts out, don’t use an impact, use a ratchet and hand tighten it.
+@bb3283 Thanks for watching our video! 1aau.to/m/Shop-TRQ
WOULD YOU PLEASE TELL ME rtv WHEN YOU PUT IT ON ENGINE sir ?
What kind of RTV is recommended is permatex high temp Red RTV ok?
What's Nm of the cover screw ?
I did this, using this video almost 2 years ago. Worked perfectly. Thanks for the video guys!
Also I love how Toyota made almost everything in this car 10mm
Looks easy. Every man should know how to do this. $20 part. Mechanic will charge $400! Big difference
Just got done with this on my 2004 toyota Camry thanks to your help.
You have also walked me through on my 2003 toyota 4runner front and rear brake and rotors.
Amazing content and great channel!
Great video. Wish I knew a local mechanic that would do this just as you did- correctly, quickly- and for a fair price. I don’t have the tools to attempt this myself.
I would use a little bit of 3M Black Super Weatherstrip and Gasket Adhesive for Autos, applying some in the channel in the valve cover where the gasket fits into. That way, it won't flop out when turning the cover over and you reinstall it over the engine. There's an increased chance of the gasket twisting or kinking without you knowing it, potentially making the oil leak worse off than prior to replacement. The RTV where the video instructs is definitely a good idea though.
reply so I can remember this info when it is time.
Got some High-Temp Red RTV, should be better.
Won’t the weatherstrip 3M be unsafe for high temps?
@@bryancertantes7198 : It won't matter because all the 3m does is hold the gasket in so it won't fall out. Once the cover is replace the 3m weatherstrip has done it's job.
I would personally just use a few small dabs of assembly fluid on the corners and sides. Should do the trick without compromising the seal.
What RTV?
Might want to hold the harnesses at both ends back out of the way with cords or bungies to facilitate a straight down angle of the cover over the two studs (or have someone hold them out of the way).
Thanks for your excellent videos. Do you think it would be OK to use a few dabs of rtv or gasket sealer to hold the gasket in place as I reinstall cover?
I just replaced the gasket on our 2005 Camry. Fairly easy, except the wiring harness on the driver's side of the cover. Also, the ventilation hose on that end was hardened & cracked, so I replaced that too.
Did this today. Was really straightforward especially with expert guidance from this vid. The only thing i did do was crack the hoses for the crankcase ventilation. They needed replacing anyway so was probably a good thing. Thanks again.
+@davidddaniel Thanks for watching our video! 1aau.to/m/Shop-TRQ
As for cleaning the spark plug tubes. I spray Carb cleaner in the tubes without removing the spark plugs, and then I use a turkey baster to suck out all the oil that leaked into the tubes. That way when you do remove the plugs the pure oil will not go into the pistons and may damage some of the emission components.
Hello should I unplug positive or negative terminal before starting due to unplugging stuff?
Couldn’t you put a little bit of grease in the groove in a few places to help hold the gasket while you put the valve cover on?
What RTV do you use ? Does it mattrr or oil resistant or high temp?
I need to do this exact service on my 2007 Camry. Can someone please specify the exact RTV I should use (there are so many kinds to choose from)...Just need a small amount as I am DIY.
Remove the 'dog bone' torque mount and you'll have more room to remove and replace the cover.
Wonderful video. I almost gave up doing this job myself. You made it look nice and simple. Thanks a lot 🙏
Hello sir . When you removed engine cover . Did you need to drain the oil out sir ? May i know it sir please ? Thank you for your help .
Draining the oil isn’t needed. Just be sure to keep the area clean to make sure nothing falls into the values and gunks it up.
Just did mine, this video helped a loooooot. So far so good. No leaks
Probably the best explanation from A to Z. Thank you for this.
Which rtv should I use?
Thanks! Was easier than I thought. Changed spark plugs too. Old gasket and plugs were badly overdue.
Nice video
Thank you for your video. Very well done, walked me though the process from end to end.
Is it a bad idea to put some RTV on the cover to hold the gasket in place from falling /sagging down?
Engine w o with out the oil burning issues on some yrs can still give u 300-400k what an engine plenty of power 2.
Hard to kill unless u don’t keep an eye on the oil level if u have a leak etc
EXCELLENT! NO EXTRA NOISE, PROBLE. IS , I KINDA LIKE HIS VOICE. HA HA! IM FROM Califreakshow! Obviously!
Hi there! Very informative video ty! What would you say is the normal price range for a job like this?
on the high side 180.00 USD while your having this done if the spark plugs are due for a change do it now this will save on labor as the plastic cover and coils have to removed anyway to change the gasket. Talk to your mechanic about it.
Valve cover vs. Rocker cover. Same thing? I am here in New Zealand and looking to do this myself. Looks like a possible job for a beginner-novice? Excellent video. Nice timing and cadence.
Thanks for the video but how many screws are around the manifold are there like that millimeters that how many of that are there like 9 total
hi thank you for this video have a 2003 Toyota Camry and the hose in 1:05 came off the car engine light was flashing and car was pup pup lol stalling i didn't know exactly where the hose belong then i watched your video what's the name off that hose and what tools do i need to remove cover please include clips and wrench please thanks
What to do if the press-release clips on the spark plug connectors break off?
What do you think about high temp rtv silicon gasket maker on cover to hold gasket in place (leave for an hour), and a bead on motor too ?
thanks!! going to change mine tomorrow after multiple cylinder misfires and discovering the leak when replacing ignition coils
Hi dear can u pls tell me what kind of hose it is which one goes to pcv valve
Great video just did mine it's still leaking. Going to do it over again. I must have done something wrong
Why do you need to torque ? Can’t you just nip them up ?
What a torque needed?
did this to my 04 camry works well
This video has helped me so much. 2002 camry 2.4
What torque wrench is that?
All the bolts were 10mm?
just finished pretty simple love the vid
Thank you very informative
Where can I get new ignition coil bolts??
Did anyone have a misfire??
what is the torque value?
Excellent video in attention-to-detail
Is there a head gasket video like this?
Great video 👍.
Thanks, this gives me confidence that I can do it.
What is RTV?