Watched this video just yesterday. Applied the DIY net hook system to two of my fishing nets. However I use two stainless steel drinking straws I found in a kitchen drawer. Easy Peezy! Thanks!
Thank you! I just used your idea but used a piece of PEX water line. I heated it with a heat gun as I pressed it between 2 pieces of flat aluminum in a bench vice. Immediately chilled it so I now have a flat strip of PEX. I formed it to appropriate angles and mounted to my net. Perfect!!! I notched the PEX and also used 3 cable tyes to secure it and then wrapped in tape. Thank you!
This is an awesome idea, I just did this to mine. I make key rings for your belt & just put it through the ring, works absolutely perfect. Thanks for the awesome idea.
Ben, this is a home run. I pimped mine out with using electricians friction tape instead of the standard black tape. Friction tape has a rough exterior so my net doesn’t slip from my hand when they’re freezing cold. To give you props, when I’m asked about it, I give them a link to your shop & a link to this video. Thanks again & hopefully I’ll be seeing you shortly.
I recently had my net cord break and had been getting by with a small clip, but after watching this video I was impressed at the simple, DIY nature of the solution and made a trip to the local hardware store. My experience was that I was NOT able to stabilize the bar from moving, even after getting it all taped up. My solution was to add a bit of gorilla glue under the rolled tape strips and bar itself to fully secure the material. I then used electrical tape per the video, but reading some of the comments if that eventually comes off, I'll move to racket tape. I also used a small stainless rod (hardware store) vs a cheap spatula, the cost difference was a few $$$ more. My opinion from the video was he did a lot more wraps than I thought necessary so I changed up the wrapping process, cross tapes along the front and generally cleaned up the lines to make it look a little better IMO. I made sure to keep the tape neat and flat and the lines aligned a bit more, I also chose to cut the tape vs tear it which makes the edges a bit ragged and not adhere as tightly as I thought it should. Overall I am happy with the solution with a few adjustments.
Great idea, I just got a Fishpond mid size (long handle) and this set up will work great. I'm going to use copper ground wire, you can get it for less than a buck a foot in any thickness you like at at any good hardware store and it is real easy to bend into shape ( you can even get a rubber cap for the end, so no snags)
Thanks and be sure to check out our Net Man product we came up with after this video at livelylegz.com. We took this idea to the next level. All the best to you as you hit the water.
Two videos in a couple days....good stuff. That's a very nice set up. I've been trying to figure out what to do with my net and your video has solved that issue. Thanks for all the tips, tricks and information you provide.
I know, we are finally getting time to film again. Thanks Gary and I'm glad you like the video and also happy it will be helpful, that's the goal here.
This setup is absolutely the best when you’re on the water. No fighting to find the net, no grip-shifting. As soon as you grab it, it is in the perfect position to be used. And quickly and effortlessly put away. Great!! The only problem I’ve encountered is when I’m off the water. While trekking through the woods or trail, any branch, vine or obstacle that brushes by the net pushes it up and off my belt. This happens enough to detract from its excellent configuration. I’m sure you’ve had this problem and wondered if you’ve come up with a way to minimize this situation and would appreciate if you would share it. Thank you
Yes we have a product out now that has a magnetic 🧲 lock that prevents that. Please go to our channel and see our new product the Net Man. Let us know what you think and thanks for checking the videos and for the support!
@@living4theoutdoors Yes, I had seen that product about the same time I came across your video. I’ll probably end up purchasing the Net Man as continually going back to pick my net off the ground is become tedious. I’d be lying if I didn’t say that I liked your “home” setup because of the “cost”. And to be clear, you’re saying that you’re able to grab the net from the Net Man exactly as you do from your version-in other words, once grabbed, it’s ready to use without shifting the grip? Thanks again. -Dave
@@christineplucker6959 sure is ready to go without shifting the grip. I’m working on a video from a Brookie trip where I am crawling and moving in some thick mountain cover and you will see the ease of the use. All the best to you Christine and watch for that video soon.
Thanks and be sure to check out our Net Man product we came up with after this video at livelylegz.com. We took this idea to the next level. All the best to you as you hit the water.
Thing is... I use a chest pack lol... I am aware you can attach it to the waist by loops and a belt but I wade in deep water. I have my net setup on a magnet system though and works excellent with a strong magnet. I may have to try out the backpack system though. Is it kind of a pain in the but to get to fly boxes and other tools and such?
Top idea, (although I would have thought of myself eventually of course lol) anyway, my version went like this; I had a belt holder for a large maglight, some aluminum flat about 1/2" wide , 2mm thick, I curved the aluminum flat, superglued to the belt holder to hold it in place, used two cable ties to secure it so I could pass tape thru and round the belt loop. I used "amalgamating tape" it has no adhesive and sticks to itself-its used to repair hoses if that helps find it so my version is reversed as the "hook" is on my belt-my net has a space where the frame and handle meet. If using your version, I'd probably glue a wader repair patch just in case the metal rod caused any damage but seeing how much use you guys put it thru I doubt thats needed?. The other thing about my version is there won't be any shouts of "where the hecks my spatula!" from the kitchen ha ha. Great idea sir, solved my problem as the magnetic holder thing was driving me nuts.Thanks for sharing.
This is an awesome setup. I've been doing this for years. The only difference is I use a flat spatula handle and shrink tube overtop the tape. I hated having my net hanging on my back. Kept getting caught and was a pain to reach when I needed it. Hanging it off my belt on my side is much nicer.
Nice video like all that you do very informative. Just got a new net with the measurement on the bottom, a little heavy and is hell retreaving if it gets loose and starts floating down stream. Got to check out that rubber net of yours.
I think it is a great idea and you have it down to a fine art. It will take a dedicated fly fisherman to go through the process, but once done they will surely appreciate the concept. I just went to a magnet a few years ago and sort of like it, so far no problems, but if I had seen this video back then I would have had the "Big "B" attachment on my net. Tight Lines....
hmm... seems the rubbing caused by taking the net off and putting it on would wear away at the waders after a while.. not to mention bending over and just about every motion would cause friction again causing it to want to rub and work a hole into the waders.. X @ this idea.. cheers!
I’ve got a Milwaukee utility knife that I clip to my belt for work everyday. It’s pretty sturdy. The knife was about 10 bucks. I wonder if that would do the trick and look a little more custom. I’ll report back on this one……..
Anytime and yes, it was available one day many years ago in my garage when I got an idea and was the perfect fit. ha ha Best of luck all season to you.
Great and simple idea, but as beauty is in the eye of the beholder, instead of electrical tape I would use tennis racket tape or bar tape (for bicycles) and even paracord to finish it off.
I would cut a neat groove with the dremel and clear epoxy it in with a light layer in the groove and down the sides to create a nice bevel with a syringe style applicator. Should serve you better than UV cure due to higher tinsel strength.
Watched this video just yesterday. Applied the DIY net hook system to two of my fishing nets. However I use two stainless steel drinking straws I found in a kitchen drawer. Easy Peezy! Thanks!
Thank you! I just used your idea but used a piece of PEX water line. I heated it with a heat gun as I pressed it between 2 pieces of flat aluminum in a bench vice. Immediately chilled it so I now have a flat strip of PEX. I formed it to appropriate angles and mounted to my net. Perfect!!! I notched the PEX and also used 3 cable tyes to secure it and then wrapped in tape. Thank you!
Way better than the holster. Thank you
This is an awesome idea, I just did this to mine. I make key rings for your belt & just put it through the ring, works absolutely perfect. Thanks for the awesome idea.
Ben, this is a home run. I pimped mine out with using electricians friction tape instead of the standard black tape. Friction tape has a rough exterior so my net doesn’t slip from my hand when they’re freezing cold. To give you props, when I’m asked about it, I give them a link to your shop & a link to this video. Thanks again & hopefully I’ll be seeing you shortly.
I've lost 2 nets already this year...I like your system Benny...doing a new one tonight! Thanks...
Love it Benny P and love what you guys are doing with Lively Legz!
Thanks Brandon and Merry Christmas 🎄! All the best to you as you hit the water.
@@living4theoutdoors Merry Christmas!
Thank you for sharing. I do mine with coat hanger wire, one wood screw and a washer. That's it, when to much rust I redo it.
I recently had my net cord break and had been getting by with a small clip, but after watching this video I was impressed at the simple, DIY nature of the solution and made a trip to the local hardware store.
My experience was that I was NOT able to stabilize the bar from moving, even after getting it all taped up. My solution was to add a bit of gorilla glue under the rolled tape strips and bar itself to fully secure the material. I then used electrical tape per the video, but reading some of the comments if that eventually comes off, I'll move to racket tape.
I also used a small stainless rod (hardware store) vs a cheap spatula, the cost difference was a few $$$ more.
My opinion from the video was he did a lot more wraps than I thought necessary so I changed up the wrapping process, cross tapes along the front and generally cleaned up the lines to make it look a little better IMO. I made sure to keep the tape neat and flat and the lines aligned a bit more, I also chose to cut the tape vs tear it which makes the edges a bit ragged and not adhere as tightly as I thought it should.
Overall I am happy with the solution with a few adjustments.
Great idea, I just got a Fishpond mid size (long handle) and this set up will work great. I'm going to use copper ground wire, you can get it for less than a buck a foot in any thickness you like at at any good hardware store and it is real easy to bend into shape ( you can even get a rubber cap for the end, so no snags)
You gotta be the quickest net in the west... probably the east, too. Fantastic idea! Hey, I bet it would work for tennis,too!
Hello, I saw your channel just now. That's a very good solution for the net! I go and make this for my selve, thanks for charing! ;-))
Thanks and be sure to check out our Net Man product we came up with after this video at livelylegz.com. We took this idea to the next level. All the best to you as you hit the water.
Great video Benny P..
I think your tape messure is older than me. Bud..
Keep up the Great Work..
Wild Man outttttt!!!!!!
Thanks Wild Man and yes, that tape has a few year on it.
Two videos in a couple days....good stuff. That's a very nice set up. I've been trying to figure out what to do with my net and your video has solved that issue. Thanks for all the tips, tricks and information you provide.
I know, we are finally getting time to film again. Thanks Gary and I'm glad you like the video and also happy it will be helpful, that's the goal here.
Love it. Thank you been struggling with the net thing lately. I think this just solved my problems.
I hope you like it Chris and best of luck on the water.
This setup is absolutely the best when you’re on the water. No fighting to find the net, no grip-shifting. As soon as you grab it, it is in the perfect position to be used. And quickly and effortlessly put away. Great!! The only problem I’ve encountered is when I’m off the water. While trekking through the woods or trail, any branch, vine or obstacle that brushes by the net pushes it up and off my belt. This happens enough to detract from its excellent configuration. I’m sure you’ve had this problem and wondered if you’ve come up with a way to minimize this situation and would appreciate if you would share it. Thank you
Yes we have a product out now that has a magnetic 🧲 lock that prevents that. Please go to our channel and see our new product the Net Man. Let us know what you think and thanks for checking the videos and for the support!
@@living4theoutdoors Yes, I had seen that product about the same time I came across your video. I’ll probably end up purchasing the Net Man as continually going back to pick my net off the ground is become tedious. I’d be lying if I didn’t say that I liked your “home” setup because of the “cost”. And to be clear, you’re saying that you’re able to grab the net from the Net Man exactly as you do from your version-in other words, once grabbed, it’s ready to use without shifting the grip? Thanks again. -Dave
@@christineplucker6959 sure is ready to go without shifting the grip. I’m working on a video from a Brookie trip where I am crawling and moving in some thick mountain cover and you will see the ease of the use. All the best to you Christine and watch for that video soon.
you guys have some of the best materials and vids Kudos
Great tips and how to information. Great idea. Keep on keeping on and Best of luck always and thanks for sharing your videos.
Thanks John!
Great video ! Thank you for the tip
What a GREAT mod! I just did mine & can’t wait to try it out! Thank you for the tip!
Great video.. Greetings from Denmark.
Genius! Thanks for sharing!
Thanks and be sure to check out our Net Man product we came up with after this video at livelylegz.com. We took this idea to the next level. All the best to you as you hit the water.
GREAT VIDEO and good info, thanks Benny and best regards from NZ, Tony.
Those nets are awesome. So light an deep to for landing the big ones.
Thanks, appreciate you noticing and yes, also the natives won't slip through the holes.
Brilliant! Thanks
Thing is... I use a chest pack lol... I am aware you can attach it to the waist by loops and a belt but I wade in deep water. I have my net setup on a magnet system though and works excellent with a strong magnet. I may have to try out the backpack system though. Is it kind of a pain in the but to get to fly boxes and other tools and such?
Another quality video Ben I will be using this as I tried to use a clip off of a tape measure which held up for one outing
Thanks Randi!
I like that rod holder. Where did you get that and how does it work?
Please go to our website livelylegz.com for the rod holder and new Net Man net holder. Thanks Charles and all the best to you as you hit the water.
Got to be from Pa. when you say Mike's bookbag. LOL
Top idea, (although I would have thought of myself eventually of course lol) anyway, my version went like this; I had a belt holder for a large maglight, some aluminum flat about 1/2" wide , 2mm thick, I curved the aluminum flat, superglued to the belt holder to hold it in place, used two cable ties to secure it so I could pass tape thru and round the belt loop. I used "amalgamating tape" it has no adhesive and sticks to itself-its used to repair hoses if that helps find it so my version is reversed as the "hook" is on my belt-my net has a space where the frame and handle meet. If using your version, I'd probably glue a wader repair patch just in case the metal rod caused any damage but seeing how much use you guys put it thru I doubt thats needed?. The other thing about my version is there won't be any shouts of "where the hecks my spatula!" from the kitchen ha ha. Great idea sir, solved my problem as the magnetic holder thing was driving me nuts.Thanks for sharing.
I love the spatula comment at the end Jaques! Best of luck on the water and we hope you slam some nice trout.
This is an awesome setup. I've been doing this for years. The only difference is I use a flat spatula handle and shrink tube overtop the tape. I hated having my net hanging on my back. Kept getting caught and was a pain to reach when I needed it. Hanging it off my belt on my side is much nicer.
Semper Fi, good video...thanks
This is a really nice idea! I always lose my net and this might prevent me from doing that anymore
Very cool idea! Thanks for the awesome video.
Thanks Jeff.
Lively Legz/Living4theoutdoors your welcome bud.
Very nice how do I get one of your nets thank you Johnny.
Awesome stuff.
Nice video like all that you do very informative. Just got a new net with the measurement on the bottom, a little heavy and is hell retreaving if it gets loose and starts floating down stream. Got to check out that rubber net of yours.
Thanks Len and let me know what you think!
I think it is a great idea and you have it down to a fine art. It will take a dedicated fly fisherman to go through the process, but once done they will surely appreciate the concept. I just went to a magnet a few years ago and sort of like it, so far no problems, but if I had seen this video back then I would have had the "Big "B" attachment on my net. Tight Lines....
Please just go to lows and buy a single screw on hook
Does anyone remember who made or the name of the old wooden nets that the handle slid down over your belt on your hip?
Awesome 😎 I just made this and it’s super Cool👍
So how long will that electrical tape last being constantly wet from deep wading?
Use Duct (Gorilla) tape Or a couple layers of Heat-shrink Tubing
Bravo.
hmm... seems the rubbing caused by taking the net off and putting it on would wear away at the waders after a while.. not to mention bending over and just about every motion would cause friction again causing it to want to rub and work a hole into the waders.. X @ this idea.. cheers!
I’ve got a Milwaukee utility knife that I clip to my belt for work everyday. It’s pretty sturdy. The knife was about 10 bucks. I wonder if that would do the trick and look a little more custom.
I’ll report back on this one……..
Great idea! Thanks for sharing. I've been looking for something like this
Thanks for watching and I'm glad it helps.
Windwalker's Outdoor Channel same here probably going to do this to my net tonight who would have thought a hamburger flipper on a net thanks Benny.P
Anytime and yes, it was available one day many years ago in my garage when I got an idea and was the perfect fit. ha ha Best of luck all season to you.
Lively Legz/Living4theoutdoors same to you! I killed the trout here in Somerset county today on luarel hill with the streamers black and pink pattern!
I like this idea, however I’ll probably use a piece of metal that’s flat and not round. The round metal seems like it may roll over time.
Great idea but I wouldn’t take up such a beauty
Great and simple idea, but as beauty is in the eye of the beholder, instead of electrical tape I would use tennis racket tape or bar tape (for bicycles) and even paracord to finish it off.
I can see how this would make a great grip! Thanks Bob and best of luck on the water.
The simple way is the best way ......tell me how to catch a trout now 😂😂😂
Could you use UV cure instead of tape?
Hmmm, I am not sure that will hold, but if you try it and it works please update us.
I would cut a neat groove with the dremel and clear epoxy it in with a light layer in the groove and down the sides to create a nice bevel with a syringe style applicator. Should serve you better than UV cure due to higher tinsel strength.
I built my own fish net system for 7 dollars, 1/3 of the magnet set-up. These stores want 20.00, which is rip off.
Really? Kinda amateurish schlock job. 20 min video to show the painful detail of a 5-year old’s idea. Wow!