Great,...in the end I didn't listen to anything, is this tool to calm the atmosphere and not a tool to amplify the sound??..I am very confused by the existence of this tool😅,..I almost bought it in an online store before watching this channel, on the ad it was a subwoofer amp, apparently it was a silent subwoofer amp, I was almost fooled by the ad, thank you very much sir because your content has saved my money💵💰✍️😊👍💪🤳🤝...
I likes the Brazilian song. It's a bit old but I still remember when it got famous in my country. Did you choose it because of rights reserved at youtube ?
I am doing the reverse engineering for this board. I'm an electrical engineer as well as English teacher. When I'm finished I published on UA-cam. You may like to know these are not MOSFET transistors. I guess some tweaks might make this become a bit stronger.
Yes sir.i think there is a little bit enhance in the sound quality.maybe next time if i have spare time to build a subwoofer box in this amplifier i use parametric equalizer to give more sound quality output.thank you
I have the PA-80d as well but mine has a black PCB instead of green like yours. Everything else seems identical. I don't use the LPF on mine because it does cut out too much signal. I have tried it with one of those 7 band EQs for car audio and it works much better. Right now I have it hooked up using a sub out RCA from my Yamaha AVR to a LPF preamp then to the PA-80d amp and that squeaks the most power out of it. I've measured around 200-220 watts rms with a cheap oscilloscope. It's powering a 600w rms 12" Audio Legion dual 2 sub wired in series to 4ohm. Shakes my entire apartment!
Yes sir addtional pre amp can increase sound output.but it depends on the power supply use.so it is better to use high current power supply o high current battery to give better sound output
@@carljosephsantiago I'm using it with a 600w computer ATX power supply. I desoldered all the 18awg wires off the PCB and replaced the 12v with 8awg wire. It delivers 46a on the 12v rail. I also power the preamp from the same power supply and I added a usb-c to the 5v rail to power a Bluetooth adapter if needed.
It is nice sir 12v high current regulated power supply is better it give less noise.itry that concept wayback 2013 i use atx power supply but instead of using 1atx i use 2 and connected in parallel to increase power but not in this amplifier by the way thank you for sharing your idea sir.pls support my channel thank you again
Idol sana masagot balak ko bumili ng ganyan amp. Tapos lalagay ko sa tricycle ko pwede naba battery ng motor mag drive sa kanya? Ct bajaj 125 motor ko idol
Pwede namn po basta 12v kaya lang po kung stock battery po mabilis din malowbat pero depende pa din po sa speaker kung maliit lang namn. D din kagad malow bat un
Dpende po sa impedance na ginamit na dummy load kung 4 ohms po pwede nasa 160 watts po yan design po kasi ung mga car amp na loadan ng 4 ohms speaker lalo po sa subwoofer
Dpende po sa voltahe na inilabas nya if lagpas 1v na dna po maganda un maninira na po talaga un pwede may nashort sa board nyan or nadikit malapit sa input section or sa linya po ng pre amp dapat na check po kasi may capacitor po yan sa input.meron din po pagkakataon na sa 24v ginamit then kumuha ng supply sa 1 battery lang para maging 12v kung ang napagkuhanan ay + ng 24 at ung negative ay kinuha sa series connection ng battery sure po un from negative ng amp at body ground ng sasakyan may makukuha na supply
@@carljosephsantiagoboz 12v dc lang po or single battery lang gamit ko, un neg voltage supply po nia at un common ng input audio nia mataas ang voltage around 12vdc po... bakit kaya...
Meron po sir.madalas nag kakaron po nun lalo na pagmabilis takbo or naka idle pero pwede po mareduce un lalagyan po ng filter coil sa b+ po.e2 po kasing amp na e2 wala po ganun dpo tulad nung mga v12 at x12 amp
Depende po kung ilang ohms and watts ang gagamitin nyo po na sub pero napang test ko po cya 2pcs d10 200watts 8ohms each ok namn po.habang tumataas po kasi ang load maslalo lumalakas ung kunsumo sa battery na.rated po nyan nasa 100w rms more or less
3.7v lng po ang battery nyan sa loob.kung gusto nyo po gamitin sa 12v need nyo po bumili ng buck converter para po bumaba ung 12v to 5v na mataas pa din ang current meron po kasi ic regulator na 5v out pero 1 amphere max kaya buck converter po masmaganda gamitin
@@carljosephsantiago lalagay ko sa tricab ko boss, lagpas 2k kasi ang 705 or 805, baka may alam ka na brand at model na kahit medjo mababa lang sa 705 pro goods ang tunog at power boss, salamat.
@@Nanel727 madami po ganyan design na amp kaya lang po puro mono.amp lang po.normal po kasi na 2k up ang presyo ng car amplifier kahit assemble pa po paki check po sa ibang video ko ung dc to dc inverter 12v lang din po gamit ko dun
Kaya nman po,yan po ba ung 1 pair lang ang opt. nasa 50 to 60w rms namn po yan.magdedepende pa din po yan sa supply nyo cyempre kung 150w po yan dapat atleast 12volts 15 amphere po ang power supply ang gagamitin nyo po
Hello good day po.dpat po naka select ung switch sa hpf para magka vocal at tweeter pag lpf po puro bass namn.pwede po kau gumamit ng parametric equalizer para macontrol nyo din ung treable.midrange at bass
Need po bumuli ng socket if ever na ayaw nyo po putulin ung dulo ng wire ng charger pwede po hanggang 15vdc.pag lumagpas po pwede na po masira ang amplifier
Kung ang pagbabasehan po ay design.yes po malakas po cya kumpara sa mga 12v ic type amplifier kasi ang design po nya ay gumamit ng dc to dc inverter na kung saan ung dc to dc na inverter ay pwede po magamit sa mga high power amplifier.pwede nyo po icheck ung ibang video ko para makumpara nyo po na masmalakas cya compair sa mga ic type amplifier.meron po ako video na dc to dc inverter.pls visit my pages salamat po
Yes sir it range from 160 to 180w rms @ 4 ohms.so if you use 8 ohms speaker it can be ranges from 80 to 100w rms and it depend in the power supply use.car amp is design to use in 4 ohms load
Bos may nabili akong motor may sound system kaso pag nakapatay makina lng gumagana. Pagnakaom makina may tiktiktik na tumutunog. Ano kaya problema nun?
Good day wala po kasi noise supressor filter yan minsan sumasabay pa po sa redundo ng makina ung speaker nya.pwede po battery operated din po ang design ng motor na nabili nyo.masmaganda po bukod nyo nalang po ng battery tapos lagyan po ng 2 wat switch para sa charging
Nasubok ko po sa 2pcs d10 350w 4 ohms pero naka series po configuration of 8 ohms pag naka parallel po kasi parang flat iron sa init 2 ohms nalng po kasi un
Depende pa din po sa speaker na gagamitin.meron lang po na selector yan para mawala ang kalansing at humina ang boses pero dpa din po solid na full bass
Madalas po kasi naka connect un sa ignition or sa car stereo dun po nakuha ng 12vdc supply bale po ung b+ rekta na sa positive ng battery bale kahit switch na maliit pwede ilagay or jumper wire na kahit ano kulay
25% of the pmpo is rms.but as you can see in the design dc to dc inverter have 2 pcs mosfet so the main amplifier cannot deliver the true rated power and the dc to dc inverter depends in the battery capacity to produce more power but if the dc to dc inverter rich the limit the mosfet will get damage or burn
Yes sir but not only the mosfet but also the torroidal transformer as you can see the diameter of the core is small.to increase the power modefy the core and then winding plus the mosfet
@@carljosephsantiago Yung parang casing na aluminum nyan sir. Kasi parang open lang yung likod. Parang alanganin ako magburas sa baffles tapos doon ko kakabit. eh malakas ang vibration nun baka masira lang agad yang mono amp.
@@Purowalangkwenta Required talaga sir lagyan ng air proofing yan if lalagay sa subwoofer box, much better kung naka seperate siya sa airflow ng subwoofer box kumbaga may sariling cabinet sa custom box. Yung sakin nilagay ko lang sa box kung san naka package yung amp, safe naman nilagyan ko rin ng fan, nakahiwalay siya sa subwoofer box. Mag 1 year na sakin sa bahay and recently nilagay ko sa sasakyan, maganda power output kahit 13v lang supply ng koryente ko.
Check fuse po.pag busted try nyo palitan.pagpumutok uli check mosfet ung dalawa po sa ilalim irfz44 madalas no.pagshorted check mo po mga diode sa paligid ung pwm i.c nyan nasisira din po tl494 no.nun yan lang po muna.pag may shorted po sa main amp mag protect din po yan
Good day po ang design po ng amplifier ay dual operation pwede cya gamitin pang low at pwede din full range kung makikita po ninyo meron switch na maliit ayun po ay cross over may naka lagay na low pass filter(lpf) para sa bass application at full para sa (fullrange) 2 way application.sa latest topology ng kahit anong amp ang ginagamit na po na pang low or bass application ay mga class d amplifier na.pero dahil po yan po ang alam ninyo at narinig nyo.salamat pa din po sa pag comment
Great,...in the end I didn't listen to anything, is this tool to calm the atmosphere and not a tool to amplify the sound??..I am very confused by the existence of this tool😅,..I almost bought it in an online store before watching this channel, on the ad it was a subwoofer amp, apparently it was a silent subwoofer amp, I was almost fooled by the ad, thank you very much sir because your content has saved my money💵💰✍️😊👍💪🤳🤝...
Thank you sir
Es para auyentar mosquitos 😅
Amigo no escuche la musica creo que fue por problemas de derechos de autor, saludos me sirvio para conectar el mio
May fan po ba kayong kinabit naiinit po kasi
mga ilang watts dapat sa rms na speaker ang puedeng gamitin idol, pls, answer me ASAP...
Kahit 200 watts rms pwede namn po pero kung meron 100 watts mas ok po d ganun kalakas sa battery at dpo hirap ung amplifier
I likes the Brazilian song. It's a bit old but I still remember when it got famous in my country. Did you choose it because of rights reserved at youtube ?
I am doing the reverse engineering for this board. I'm an electrical engineer as well as English teacher. When I'm finished I published on UA-cam. You may like to know these are not MOSFET transistors. I guess some tweaks might make this become a bit stronger.
Thank you for sharing your idea sir.
Please answer me, is it good or not?
Yes sir it is good ans cheaper
I'd leave it on flat and apply a cut with a dsp. I think this might get more out of the amplifier
Yes sir.i think there is a little bit enhance in the sound quality.maybe next time if i have spare time to build a subwoofer box in this amplifier i use parametric equalizer to give more sound quality output.thank you
I have the PA-80d as well but mine has a black PCB instead of green like yours. Everything else seems identical. I don't use the LPF on mine because it does cut out too much signal. I have tried it with one of those 7 band EQs for car audio and it works much better. Right now I have it hooked up using a sub out RCA from my Yamaha AVR to a LPF preamp then to the PA-80d amp and that squeaks the most power out of it. I've measured around 200-220 watts rms with a cheap oscilloscope. It's powering a 600w rms 12" Audio Legion dual 2 sub wired in series to 4ohm. Shakes my entire apartment!
Yes sir addtional pre amp can increase sound output.but it depends on the power supply use.so it is better to use high current power supply o high current battery to give better sound output
@@carljosephsantiago I'm using it with a 600w computer ATX power supply. I desoldered all the 18awg wires off the PCB and replaced the 12v with 8awg wire. It delivers 46a on the 12v rail. I also power the preamp from the same power supply and I added a usb-c to the 5v rail to power a Bluetooth adapter if needed.
It is nice sir 12v high current regulated power supply is better it give less noise.itry that concept wayback 2013 i use atx power supply but instead of using 1atx i use 2 and connected in parallel to increase power but not in this amplifier by the way thank you for sharing your idea sir.pls support my channel thank you again
Idol sana masagot balak ko bumili ng ganyan amp. Tapos lalagay ko sa tricycle ko pwede naba battery ng motor mag drive sa kanya? Ct bajaj 125 motor ko idol
Pwede namn po basta 12v kaya lang po kung stock battery po mabilis din malowbat pero depende pa din po sa speaker kung maliit lang namn. D din kagad malow bat un
Clase D?
AB?
AB po.
Yung smaller brother nya na 600watts ginamitan ng dyno umabot ng 130watts max so this thing should be around 150watts more or less.
Dpende po sa impedance na ginamit na dummy load kung 4 ohms po pwede nasa 160 watts po yan design po kasi ung mga car amp na loadan ng 4 ohms speaker lalo po sa subwoofer
puwede ba ikabit jan ang 3x 4ohm na speakers so 12ohm total in series.
Pwede namn po kasi ung mga ganyang amp po madalas working namn po cya from 4 ohms to 16 ohms common po sa mga class ab amplifier
Class D PO BA YAN AMPLI MO
boz bkit un negative ng input may voltage ako nkukuha together the neg of supply? kaya un car stereo ko nasira pagkabit ko po dyan sa car amplifier..
Dpende po sa voltahe na inilabas nya if lagpas 1v na dna po maganda un maninira na po talaga un pwede may nashort sa board nyan or nadikit malapit sa input section or sa linya po ng pre amp dapat na check po kasi may capacitor po yan sa input.meron din po pagkakataon na sa 24v ginamit then kumuha ng supply sa 1 battery lang para maging 12v kung ang napagkuhanan ay + ng 24 at ung negative ay kinuha sa series connection ng battery sure po un from negative ng amp at body ground ng sasakyan may makukuha na supply
@@carljosephsantiagoboz 12v dc lang po or single battery lang gamit ko, un neg voltage supply po nia at un common ng input audio nia mataas ang voltage around 12vdc po... bakit kaya...
Boss pag pangbahay lang ano pwede gamitin power supply sa knya bukod sa battery
Smps 12v 30A 350w po sa online shop po meron nasa 700 pesos up po un.masmataas amphere rating masmaganda po
Pwede n po ba 12v 6A.
N power supply
sir kamusta ang ampli, may Humming sound ba na lumalabas yung galing engine?
Meron po sir.madalas nag kakaron po nun lalo na pagmabilis takbo or naka idle pero pwede po mareduce un lalagyan po ng filter coil sa b+ po.e2 po kasing amp na e2 wala po ganun dpo tulad nung mga v12 at x12 amp
@@carljosephsantiago ok ok tnx
Boss tingin mo good siya for sub? 2 D12 balak ko na sub. Pangmotor
Depende po kung ilang ohms and watts ang gagamitin nyo po na sub pero napang test ko po cya 2pcs d10 200watts 8ohms each ok namn po.habang tumataas po kasi ang load maslalo lumalakas ung kunsumo sa battery na.rated po nyan nasa 100w rms more or less
Umiinit sya paano ginagawa nyo?
Boss kaya po ba nya idrive ung 800 watts 4ohms thanks po.
Depende po kung watts rms po malamang hindi po.
sir kaya nya ba e load sa Monitor na 12V?? Kahit wlang kang battery??
3.7v lng po ang battery nyan sa loob.kung gusto nyo po gamitin sa 12v need nyo po bumili ng buck converter para po bumaba ung 12v to 5v na mataas pa din ang current meron po kasi ic regulator na 5v out pero 1 amphere max kaya buck converter po masmaganda gamitin
@@carljosephsantiago OK sir thank you po sa next video nyo paturo nman po kung paano sya lagyan ng Cooling fan thanks po
Single chanell lang boss? Ok sana kung 2 chanell na may full at lpf ang 1.
Pang boom box po kasi ung mga ganyang amplifier normaly sub application po talaga yan
@@carljosephsantiago ahh, kaya pala, maraming salamat boss.
@@carljosephsantiago boss, pa recommend po ng car amp na nasa mga 1.5k to 2k na halos mrv 705 ang tunog or kahit mababa sa mrv 705.
@@carljosephsantiago lalagay ko sa tricab ko boss, lagpas 2k kasi ang 705 or 805, baka may alam ka na brand at model na kahit medjo mababa lang sa 705 pro goods ang tunog at power boss, salamat.
@@Nanel727 madami po ganyan design na amp kaya lang po puro mono.amp lang po.normal po kasi na 2k up ang presyo ng car amplifier kahit assemble pa po paki check po sa ibang video ko ung dc to dc inverter 12v lang din po gamit ko dun
pwede ba i overvolt yan , kabitan ko ng 36 volts para mas malakas?
Hindin po.hanggang 14vdc lang po
Pwede po b jan 12v 5ampers
kaya ba i drive ang 12 inches subwoofer 300wats rmzs
Yes po..pero mabilis dn mag init.
how can i buy it in kenya
Pls Try to search sir in any online store like aliexpress or alibaba
Kaya po kaya yung 150Wats Sa Class PA-60A?
Kaya nman po,yan po ba
ung 1 pair lang ang opt. nasa 50 to 60w rms namn po yan.magdedepende pa din po yan sa supply nyo cyempre kung 150w po yan dapat atleast 12volts 15 amphere po ang power supply ang gagamitin nyo po
Opo. gagawin ko lg pang bass. salamat po
Sur paano po yan lagyan ng vocals at tweeter
Hello good day po.dpat po naka select ung switch sa hpf para magka vocal at tweeter pag lpf po puro bass namn.pwede po kau gumamit ng parametric equalizer para macontrol nyo din ung treable.midrange at bass
Yong equalizer po ba ay 12 volts din
Eh pano po input nyan pag da power supply n pang loptop
Need po bumuli ng socket if ever na ayaw nyo po putulin ung dulo ng wire ng charger pwede po hanggang 15vdc.pag lumagpas po pwede na po masira ang amplifier
Kaya po kaya nito d15 subwooder 1200rms
Kaya namn po kaya lang dpo mabibigay ung full potential ng speaker almost 160watts rms lang po sa 4 ohms yan
Sir malakas po ba yan na amplifier kysa mga ordinaryong 12v amplifier? Balak q kasi bumili
Kung ang pagbabasehan po ay design.yes po malakas po cya kumpara sa mga 12v ic type amplifier kasi ang design po nya ay gumamit ng dc to dc inverter na kung saan ung dc to dc na inverter ay pwede po magamit sa mga high power amplifier.pwede nyo po icheck ung ibang video ko para makumpara nyo po na masmalakas cya compair sa mga ic type amplifier.meron po ako video na dc to dc inverter.pls visit my pages salamat po
@@carljosephsantiago wow ok sir tnx
Real rms power??
Good day maybe It is range from 80 to 100watts rms base on the component install in the board
I saw a test in which it gave 170 wrms.
Yes sir it range from 160 to 180w rms @ 4 ohms.so if you use 8 ohms speaker it can be ranges from 80 to 100w rms and it depend in the power supply use.car amp is design to use in 4 ohms load
Pwde po b n iconect Yan sa bhy , kurywnte
Gagamit po kau ng power supply 220v to 12v atleast 6 amphere po
Pwede n po pla ang 6amper pataas po ba
Bos may nabili akong motor may sound system kaso pag nakapatay makina lng gumagana. Pagnakaom makina may tiktiktik na tumutunog. Ano kaya problema nun?
Good day wala po kasi noise supressor filter yan minsan sumasabay pa po sa redundo ng makina ung speaker nya.pwede po battery operated din po ang design ng motor na nabili nyo.masmaganda po bukod nyo nalang po ng battery tapos lagyan po ng 2 wat switch para sa charging
@@carljosephsantiago ok may saktong AMPERES ba o Anong klaseng noise suppressor bilhin ko?
Kaya poba nya dalawang 350wats sir.?
Nasubok ko po sa 2pcs d10 350w 4 ohms pero naka series po configuration of 8 ohms pag naka parallel po kasi parang flat iron sa init 2 ohms nalng po kasi un
Sir meron ako targa d10 300watts at 2pcs pang boses pwede ko ba cila pag isahin jan sa ampli na yan salamat po
Pwede namn po basta Configure nyo po ng 8 ohms ung bawat sub para dpo mag init ng husto ung amplifier.para pagnagparallel po ay lalabas ng 4 ohms
Boss pano mo kinonnect yung pang hi mo?
Bale nilagyan ko lang din po ng non polar capacitor 4.7uf/100v tapos naka select po ng fullrange ung amp
@@carljosephsantiago may speaker kasi ako dito na japan bookshelf pwede ko kaya sya i connect pang mid hi?
Malakas po ba ang bass nyan
Depende pa din po sa speaker na gagamitin.meron lang po na selector yan para mawala ang kalansing at humina ang boses pero dpa din po solid na full bass
Bkit mhina ang bass
Sabi po kc sa rating MALKAS daw bass po
Boss pagbili nyo ng amplifier Kasama nb Ang mga wire
Not included po ang mga wires..unit only po sya
Boss yung remote yung blue conector mo pwede ba yan kahit anu wire. Gamitin?
Madalas po kasi naka connect un sa ignition or sa car stereo dun po nakuha ng 12vdc supply bale po ung b+ rekta na sa positive ng battery bale kahit switch na maliit pwede ilagay or jumper wire na kahit ano kulay
Ilang ohm po ung pdeng iload ?
4to8ohms po
Pmpo 1000 wat = 100 wat rms ?
25% of the pmpo is rms.but as you can see in the design dc to dc inverter have 2 pcs mosfet so the main amplifier cannot deliver the true rated power and the dc to dc inverter depends in the battery capacity to produce more power but if the dc to dc inverter rich the limit the mosfet will get damage or burn
We replace the MOSFETs , the power transistors from the dc-dc converter and the diodes so that I can give more power.
Yes sir but not only the mosfet but also the torroidal transformer as you can see the diameter of the core is small.to increase the power modefy the core and then winding plus the mosfet
Boss wala bang nabibiling box nyan?
Ano po box ung sa sub po ba.pwede namn po gawan
@@carljosephsantiago Yung parang casing na aluminum nyan sir. Kasi parang open lang yung likod. Parang alanganin ako magburas sa baffles tapos doon ko kakabit. eh malakas ang vibration nun baka masira lang agad yang mono amp.
@@Purowalangkwenta Required talaga sir lagyan ng air proofing yan if lalagay sa subwoofer box, much better kung naka seperate siya sa airflow ng subwoofer box kumbaga may sariling cabinet sa custom box. Yung sakin nilagay ko lang sa box kung san naka package yung amp, safe naman nilagyan ko rin ng fan, nakahiwalay siya sa subwoofer box. Mag 1 year na sakin sa bahay and recently nilagay ko sa sasakyan, maganda power output kahit 13v lang supply ng koryente ko.
Sir ano battery gamit mo jan ?
Deep cycle battery po pang solar po 12vdc 18AH po
my ganyan ako bigla nlang namatay pumutok fuse ng amp
@@gloriaromero125 check po ung mosfet ung 2 po sa ilalim na 3 pin irfz44 po ang part no.check din po diode baka shorted din
Po
ভাইয়া আমি এমবি ফায়ারটা নিতে চাই ফাটা নেওয়ার জন্য আপনার সাথে কিভাবে যোগাযোগ করবো আর নইলে আপনি অবশ্যই আপনারা আমার সাথে যোগাযোগ করবেন
Good day sir.plz check online for that item.i buy that on shoppe ph
bos ilang watts and subwoofer na ginamit mo
thanks sa reply sir
6inches 40watts@4ohms po
The video is not clear please
Try to "higher your picture quality" sir.thanks
còn hàng ko shop
Im sorry but i order it from online shop
No sound, testing part
Muted part due to copy right claim plz check link below for testing.thank you
Lods... Sana mapansin ganyan sakin lods ayaw mag power lods...
Check fuse po.pag busted try nyo palitan.pagpumutok uli check mosfet ung dalawa po sa ilalim irfz44 madalas no.pagshorted check mo po mga diode sa paligid ung pwm i.c nyan nasisira din po tl494 no.nun yan lang po muna.pag may shorted po sa main amp mag protect din po yan
nice
mono only, not stereo..
Yes,that amp is mono
What do you mean by mono only
Good day sir mono means single channel amplifier
tinagalog mona lng para maintindihan ng iba
Cge sir gawan natin tagalog.pacnxa na po nagtatry palang po kasi ako dyan
di po mgnda tunog dapt po base lng yn
Good day po ang design po ng amplifier ay dual operation pwede cya gamitin pang low at pwede din full range kung makikita po ninyo meron switch na maliit ayun po ay cross over may naka lagay na low pass filter(lpf) para sa bass application at full para sa (fullrange) 2 way application.sa latest topology ng kahit anong amp ang ginagamit na po na pang low or bass application ay mga class d amplifier na.pero dahil po yan po ang alam ninyo at narinig nyo.salamat pa din po sa pag comment
Stap englishing just fure tagalog
Please answer me, is it good or not?
Good day sir.yes it is good to use in compatible speaker.it is better to used in sub application you can use 200watts 4 ohms subwoofer speaker
@@carljosephsantiago Compared to ZK6001 which one is better?
I'm going to use it as a subwoofer.