[新手講座] 遙控器轉向設定入門
Вставка
- Опубліковано 23 жов 2021
- 間唔時都會有入門車友問，唔明點解架車SET極支控都SET唔直架車，又或者一開控架車就側埋一邊，再唔係就係架行上嚟側埋一邊等等。其實唔少都係因為係砌果時或初初設定SERVO轉向時，冇留意到一啲事項。
今次我哋就住遙控器轉向設定，同大家講解下應該點去SET架車SERVO中位之餘，再講下遙控器上ST TRIM，D/R，EPA同EXP其實有乜用，同埋個用法係點樣。
如果想瞭解多啲，就記得要睇吓喇!
更多討論
遙控工房討論區 - rc-evo.com
遙控工房MEWE - mewe.com/p/rcevolution
遙控工房FB - rcevo00
業務聯絡:
可於我們FB專頁以Messager聯系
/ rcevo00
Happy by Luke Bergs / bergscloud
Creative Commons - Attribution-ShareAlike 3.0 Unported - CC BY-SA 3.0
Free Download / Stream: bit.ly/3mRnuIb
Music promoted by Audio Library • Happy - Luke Bergs (No... - Наука та технологія
![[更新教學] Radiomaster TX16S固件重大更新 - 終於有中文系統同觸屏控制](http://i.ytimg.com/vi/hby8N8itIR8/mqdefault.jpg)
![[更新教學] Radiomaster TX16S固件重大更新 - 終於有中文系統同觸屏控制](/img/tr.png)
![[遙控學堂] Set車工具點樣用? - EP遙控車Set車工具指南](http://i.ytimg.com/vi/7aynuHZiM7I/mqdefault.jpg)
![[遙控學堂] 遙控器設定 - 轉向油門D/R及EXP使用教學](http://i.ytimg.com/vi/mTBZ-ZnKEJw/mqdefault.jpg)
多謝詳細教學，對新手真係好有用👍🏻
原來係咁，好有用。
學到很多，謝謝你🙏🏼🙏🏼🙏🏼
总结 要先买支贵枪😜
感谢分享🙏
對新手有用
非常好的影片, Amat! 本人有一個小問題想請教，就係調較好EPA(左85%,右110%, Dr 100%, 左右steering angle 28度)後再調低DR去到80%左右，用尺度出黎的左右steering angle會有相差2-3度，請問是否正常？🙏
咁要睇架車個轉向設計，本身會唔會有大細灣。
另外仲有就係果個SERVO HORN同推桿嘅角度，仲有支SERVO HORN推桿同轉向推桿是否平衡等等，都會有一定影響。
試睇下SERVO HORN支推桿係咪同SERVO HORN，中位時係咪呈直角，同埋睇下SERVO HORN推桿同轉向橋，會唔會太斜，適當地加返戒子，都可以對你講嘅問題有幫助。
非常感激🙏,我會試試。
你好，我係新手用緊Spektrum™ DX3 + SR6100AT 接收，但係搖控正中時servo 就係-90‘，我要靠ST 去扭返servo 中位，請問你有無遇過咁情況？
點解你唔拆個SERVO HORN出嚟裝返啱個位而要去較個STEERING TRIM呢?
你拆咗個SERVO HORN，開著架車，然後先裝個SERVO HORN上去，咁咪唔駛扭個TRIM。
Is it normal for the rear toe ARS link will out by 0.x mm to get the same toe angle on both sides after a while?
What is the best way to mount the setup station camber gauge on the wheel hex? You can actually tilt the gauges in/out and you will have slightly different toe reading..
Normally ARS will not out or value change after several run, unless you crash your car.
It the reading slightly different when you have a tiny move of the setup station, that's mean your setup station got issue, wear out or deform. Or you have install in a wrong way.
@@RCEVOLUTION that’s because the wheel hex is very thin and the axle shaft has a bit of play in the bearing/hub. You can actually tilt the camber gauge in/out one.. 😁
For eg at 30:31 if you force it a bit the gauge can actually toe in/out..
請問我新 set套搖控好明顯發覺前向速度慢過後向速度，点解呢？
如果跟據你嘅內容，通常都係因為SET錯前後波而導致。
但由於我地唔清楚你係乜嘢遙控器，又唔清楚你係用乜電變等，我地亦俾唔到任何解決方法俾你。
最好嘅辦法係你攞返你架車去你買果間鋪頭到問，咁係最直接同最快解決嘅方法。
Do I need to recalibrate the esc if I rebind my servo from ssh or ssr?
Normally better to do so, as some of the mode have different frequency range, end point maybe not the same.
Some of the radio/transmitter can set those mode by channel, but some of them not. So better to calibrate again to ensure the best performance.
@@RCEVOLUTION yes the end point for the servo is not the same between ssh and ssr. Ssr has much smaller EPA than ssh and it is super fast/sensitive.. 👍🏻
I recalibrated the esc also and the parameters are still the same in the program card as before.. 😁
EPA左右不一致應該會導致轉向線性不一致，最好都係平均分配一下好d
我係片入面有講到呢個問題同點處理。
一支控怎樣set兩架車
買支有記憶功能同模型選擇嘅中級控就可以。
入門級通常都冇記憶功能，中級至高級先會有。
点解向前就好直。向返后就唔直？？
因為遙控車設計係向前後，唔係向後。
架車向後，風阻唔同晒，定風翼有影響，車殼有影響，個TOE IN OUT掉轉晒，行唔直係正常。
所以玩比賽啲車，係唔會SET有後波。
@@RCEVOLUTION Thank you!
我部tt-02前進轉向完全冇問題，但係後退唔到，想問下係遙控器定車問題？求解答🙏🙏🙏🙏
有冇SET好個電變呀?
@@RCEVOLUTION 有啊，乜都set好曬，向前行同轉彎都冇問題，淨係向後有問題😅
向後咩問題?
@@RCEVOLUTION 按向後嘅製就冇反應
有冇後波主要都係電變問題。建議你睇下說明書係咪冇對好中位，又或者係咪熄咗後波。
如果都搞唔掂就最好去返買果間鋪頭到搵協助。