NOTE: If you have a manual IS250 the hyperflash turn signal relay is on the (RIGHT NOT on the LEFT) side underneath the steering wheel. For the longest time my mechanic had a hard time locating relay. LUCKILY he was able to find it while car was in accessory/battery mode. He turned on the turn signal and was able to track the location of the relay by its sound.
Thank you very much Binh for this video, this worked perfectly on my 2008 IS F. Ever since I bought my car it had hyper flash even though all the bulbs were working and no led’s installed. I couldn’t figure out the problem until I installed this relay and now no more hyper flash. For those of you who are struggling with the clip simply get a pair of pliers and push on it from the bottom and it will come right off without breaking too. On another side note be very careful when taking the clip off of the other relay, I used to much force with just my hand and when it came off I simultaneously cracked my nail and immediately started bleeding, learn from my mistake please
Binh! Thank you for this video. I just installed an LED flasher relay and no more hyper flash with my HC motions. I did notice the very brief delay when turning on a signal but nothing too bad. Keep up the great work.
For anyone who struggles with expandable nylon clips like the one at 1:52 or 2:20, press an empty socket (from a socket wrench set) onto the back of the clip. This releases the clip. You may have to try several sockets to find the exact size needed to release it.
@@hunchojack2614 i had the issue where my left blinker would blink faster than my right one and it was because of that relay. it fixes all aftermarket lights basically
Thank you for this video i actually watched your HC motion install and its 🔥👌 my only question is, if i buy that adjustable relay flasher or the non adjustable one, i see that you have all the wires, is it just plug n play and so that means i dont need to buy a resistor? I have a 2009 350. Thanks
thank you, after taking my ISF Lexus into Averis and Box Timaru NZ because I replaced an HID fog lamp it still didn't work. So the sparkie removed all of my HID system? and installed a plus 130 H11 bulbs look shit I will try them out at night but has not got the powerful blue look. I then took off home and noticed my LED indicators hyper flashing! I phoned the people saying nothing that they have done, so it must have been a resister fitted in the Tom's HID wiring for the LED indicator bulbs so I now know what to do! Thanks again, my friend.
Hey man, I have the same headlight/taillight setup on my 2IS and facing hyper blinking. Is this relay plug and play? I don't need to do any extra wiring right? I'm a total newbie so I need to know this if I wanna install this myself. Thanks for the video! Help is appreciated.
Hey! I installed the reader today and it solved my hyperblinking issue (HC motion headlights like the ones in your video) and now both my tail lights and headlights don’t flash on whenever I lock and unlock the car. I checked the fuses and nothing seems out of the ordinary… any ideas???
Nice and Quick video , but is that green relay supposed to be attached or glued to the LED Flasher relay? Got the exact same one but just wanted to make sure before installing .
Hey I currently have in vlands out of no where when i turn on signals inside the car there is a buzzing sound and also no signals flashing on the dash, but it flickers outside on headlights, hazards also don’t work nor the back. only low beam and when i break the light on the rear works which is also vland 2006 what could be the case?
If only driver side of the car is hyperflashing (headlight and tail, both HC motion sequential) would the relay make both still flash the at the same speed regardless of one only hyperflashing? And does it also resolve the taillight hyperflashing too as well? Hazards dont hyperflash only turn signal.
The animation is activated when the unlock happens (two turn signal blinks) when car is off. Make sure power is connected to battery and inline fuse isn’t blown.
Hey Bihn, I installed my VLAND headlights. When I turn on the headlights everything works fine but when I turn off the light so that the drl are on the all of the lights flicker and I can hear the a sound like the high beam turning on and off. Any idea?
Clean install great gob on how to install . Question do you know if they have a similar device like the one you installed on the Scion tC for the led bulbs I have to prevent that hyper flash ?
Hi Binh! I installed vland head and taillights but i got hyperflash only on the passenger side. This results in my DRL led bulbs being off on the passenger side. only the check lights up, the check (hyper)flashes as a signal instead of the sequential amber light, and my rear passenger amber bulb turn signal light stays on as if I’m always signaling right. When i do signal right via the turn signal knob, it hyperflashes and just goes dim to bright repeatedly until turned off. I was told i needed resistors/load equalizers but im not wire saavy like you and i didnt know which wires to tap into on the vlands so i ordered these relays in your video today. Theyre arriving wednesday. My questions are: 1) once the relay is installed, will my headlight drl/regular/high beam bulbs work again and 2) will the signal in the rear turn off and only turn on when signaling? Have you heard off or encountered this issue before? I know this was lenghty but if you made it this far I appreciate you. Been dealing w this since my oem head/tail lights and they would periodically work fine every once in a while then go back to hyperflashing. Hope to hear from you soon
Sounds like you have a short in the harness causing power to cross somewhere. explains why rear light is always orange. You should check the pins and overall harness next the junction to headlights. Might be corrosion or an old repair.
@@TunerwithKids i just installed the relay. The hyperflash is gone but the amber light stays on like you said and the headlight is off except for the check. Could you elaborate on what you replied to me ?
You’re looking for corroded plugs for main harness to headlights that is causing the turn signals to stay on. Also could be wiring that’s been cut or damaged. Somewhere it’s getting constant power to stay on.
@@TechCash14yo bro I just installed the headlights too and am having the exact same issue. I bought the item from the video but were you able to fix it the passenger blinker?
Mine stopped working on the headlight sides. The ones beside the wing are working. What would be the problem? I replaced all fuses today. And the flashers aren't working even in parking mode. The rear one works as normal
@@TunerwithKids Thank for your reply? That makes sense. I checked Lexus UK owners forum and someone had similar issue. And his problem was fixed after he placed a resistor to the tail lights. I guess it happened a few weeks after I installed the new HCmotion tail lights. I will replace this relay this week and also replace all bulbs on my OEM head lights. Also I guess I will need to add a 6 Ohms resistor to the tail lights. Do you think that would solve the problem or do you think it something else? Thank you so much for all your vides, they are always so helpful
Thanks for the video. That white tab is no joke. Took me forever :). Btw…do you still notice a delay after the click like the other one? Thank you again!
Can someone help me. I have after market headlights and taillights. So i have hyper flash only for the left blinker but the hazards are normal? Only half of the taillights flash on the back when I signal left. No issues when I signal right. Again no issues when I use hazards. How do I fix this and if I buy this would it fix it?
Hi Binh, just bought the same headlights you have on your car for my car, a 2006 IS250. Question; do you think I need to (tap the blinker line) install resistors to prevent hyper flash?
yes I unhooked the wrong relay I found it with the signals on. It was hiding next to it. Also I bought some lights with the resistors built in. Kinda of expensive but easy. Thanks
What can I do if only my left turn signal on my sequential taillights hyper flashes? It didn’t before but out of nowhere only my left turn signal started hyper flashing.I have vland front headlights and b/c sequential taillights.
Hey man So I recently bought some vlands and the amber blinker only worked on one side and the other side was just flashing white. I figured it was the relay so i switched it out but after i switched it out all the blinkers on both the front and back stopped working along with the blinker arrows on the dash. Why could this be?
I didn't buy from Amazon, I bought from Aliexpress, found it cheaper there, they have stock but shipping takes longer. I have stuff which I bought back in April, still haven't arrived yet.
Hey I have a 2010 lexus Is. My set up is vland headlights and hc motion tailights. Recently I've been noticing the blinkers hyper flashing when the headlights are on. All the lights themselves work perfectly. The hazards work perfectly wether the headlights are on or not. Still running stock flasher module. Do you think it's also the flasher module and time to upgrade ???
@@prashundey4247 yoo! just got new lights today on my is 2010 too! my headlights and taillights have hyper flashing, but is normal with emergency lights. any suggestions?
@@emmanuelrodriguez1166 in what scenerio it hyper flashes is prolly irrelevant, as long as no bulbs are out. The led flasher relay should do the trick. Solved all my problems and the speed adjustment on it is helpful to.
NOTE: If you have a manual IS250 the hyperflash turn signal relay is on the (RIGHT NOT on the LEFT) side underneath the steering wheel. For the longest time my mechanic had a hard time locating relay. LUCKILY he was able to find it while car was in accessory/battery mode. He turned on the turn signal and was able to track the location of the relay by its sound.
Thank you very much Binh for this video, this worked perfectly on my 2008 IS F. Ever since I bought my car it had hyper flash even though all the bulbs were working and no led’s installed. I couldn’t figure out the problem until I installed this relay and now no more hyper flash. For those of you who are struggling with the clip simply get a pair of pliers and push on it from the bottom and it will come right off without breaking too. On another side note be very careful when taking the clip off of the other relay, I used to much force with just my hand and when it came off I simultaneously cracked my nail and immediately started bleeding, learn from my mistake please
You should definitely make a video about the side view mirrors! Pretty sure a lot of older gens would appreciate it 🫶🏽
Facts bro
Binh! Thank you for this video. I just installed an LED flasher relay and no more hyper flash with my HC motions. I did notice the very brief delay when turning on a signal but nothing too bad. Keep up the great work.
For anyone who struggles with expandable nylon clips like the one at 1:52 or 2:20, press an empty socket (from a socket wrench set) onto the back of the clip. This releases the clip. You may have to try several sockets to find the exact size needed to release it.
worked for me, thank you so much !! was able to fix my hyper flash issue in the is250 2006 . VLAND installed headlights. super easy and accessible.
What was your issue
@@hunchojack2614 i had the issue where my left blinker would blink faster than my right one and it was because of that relay. it fixes all aftermarket lights basically
Thanks man I been needing a solution to that and you found it !!!
Thank you for this video i actually watched your HC motion install and its 🔥👌 my only question is, if i buy that adjustable relay flasher or the non adjustable one, i see that you have all the wires, is it just plug n play and so that means i dont need to buy a resistor? I have a 2009 350. Thanks
thank you, after taking my ISF Lexus into Averis and Box Timaru NZ because I replaced an HID fog lamp it still didn't work. So the sparkie removed all of my HID system? and installed a plus 130 H11 bulbs look shit I will try them out at night but has not got the powerful blue look.
I then took off home and noticed my LED indicators hyper flashing! I phoned the people saying nothing that they have done, so it must have been a resister fitted in the Tom's HID wiring for the LED indicator bulbs so I now know what to do! Thanks again, my friend.
So I installed a different relay but mine doesn’t have the lock indicator lights when I click lock on my fob. Does this relay have that same issue?
Did you find a solution? I just put mine in today and noticed that as well.
Hey man, I have the same headlight/taillight setup on my 2IS and facing hyper blinking.
Is this relay plug and play? I don't need to do any extra wiring right? I'm a total newbie so I need to know this if I wanna install this myself.
Thanks for the video! Help is appreciated.
Yes it is...didn't you see in the video?
Does the non adjustable led relay offer the one tap 3 flashes?
Hey! I installed the reader today and it solved my hyperblinking issue (HC motion headlights like the ones in your video) and now both my tail lights and headlights don’t flash on whenever I lock and unlock the car. I checked the fuses and nothing seems out of the ordinary… any ideas???
Check if the hazard work. I think the lock unlock blink uses that.
I got the vlands headlights and the blinker on the passenger side blinks fast like is going out but i got the lights today what should I do
Nice and Quick video , but is that green relay supposed to be attached or glued to the LED Flasher relay? Got the exact same one but just wanted to make sure before installing .
Oh that was my old one I taped to new so I wouldn’t lose it.
@@TunerwithKids Oh okay yeah you did say that in the vid , did the LED Relay throw any codes or engine light on ?
Thanks for the video, it helped me for my tailight hc motion 😉
Hey I currently have in vlands out of no where when i turn on signals inside the car there is a buzzing sound and also no signals flashing on the dash, but it flickers outside on headlights, hazards also don’t work nor the back. only low beam and when i break the light on the rear works which is also vland 2006 what could be the case?
If only driver side of the car is hyperflashing (headlight and tail, both HC motion sequential) would the relay make both still flash the at the same speed regardless of one only hyperflashing? And does it also resolve the taillight hyperflashing too as well? Hazards dont hyperflash only turn signal.
Yea the relay will fix it all. The hyper flash on one side is due to bad resistors in the lights.
@@TunerwithKidsfixed the issue on my 06 is350, you’re the goat thank you!
Hello, how to make comfortable turn signals. single press 3 flashing turn signals
Installed the led relay to stop hyperflashing but now the animation not working any way to.fix this?
The animation is activated when the unlock happens (two turn signal blinks) when car is off. Make sure power is connected to battery and inline fuse isn’t blown.
Hey Bihn, I installed my VLAND headlights. When I turn on the headlights everything works fine but when I turn off the light so that the drl are on the all of the lights flicker and I can hear the a sound like the high beam turning on and off. Any idea?
Your OEM DRL needs to be disabled in techstream.
@@TunerwithKids I will give this a try and give you an update. Maybe a live q&a video some time lol
@@TunerwithKids that was the fix! I had @rodneyauyeung turn off my drls.
Clean install great gob on how to install . Question do you know if they have a similar device like the one you installed on the Scion tC for the led bulbs I have to prevent that hyper flash ?
Scion TC should use exact same relay. Pull stock one and get the part number. Should match the Toyota version used on almost all their cars.
Its about 90 flash /min according to safty regulation
Hey, do you know how I can find a shop in St. Petersburg, FL that will replace the relay for me?
Have you got a video regarding the mirrors?
No…did those a long time ago. Was thinking of creating one to show wiring the parking light and turn signal but no time.
Would this relay work for newer Lexus? 2022
No. They switched to onboard control units now.
Hi Binh! I installed vland head and taillights but i got hyperflash only on the passenger side. This results in my DRL led bulbs being off on the passenger side. only the check lights up, the check (hyper)flashes as a signal instead of the sequential amber light, and my rear passenger amber bulb turn signal light stays on as if I’m always signaling right. When i do signal right via the turn signal knob, it hyperflashes and just goes dim to bright repeatedly until turned off. I was told i needed resistors/load equalizers but im not wire saavy like you and i didnt know which wires to tap into on the vlands so i ordered these relays in your video today. Theyre arriving wednesday.
My questions are: 1) once the relay is installed, will my headlight drl/regular/high beam bulbs work again and 2) will the signal in the rear turn off and only turn on when signaling? Have you heard off or encountered this issue before? I know this was lenghty but if you made it this far I appreciate you. Been dealing w this since my oem head/tail lights and they would periodically work fine every once in a while then go back to hyperflashing. Hope to hear from you soon
Sounds like you have a short in the harness causing power to cross somewhere. explains why rear light is always orange. You should check the pins and overall harness next the junction to headlights. Might be corrosion or an old repair.
@@TunerwithKids what is it that I’m looking for? How can i fix it? You said to look where?
@@TunerwithKids i just installed the relay. The hyperflash is gone but the amber light stays on like you said and the headlight is off except for the check. Could you elaborate on what you replied to me ?
You’re looking for corroded plugs for main harness to headlights that is causing the turn signals to stay on. Also could be wiring that’s been cut or damaged. Somewhere it’s getting constant power to stay on.
@@TechCash14yo bro I just installed the headlights too and am having the exact same issue. I bought the item from the video but were you able to fix it the passenger blinker?
This is pretty sick.
Noticed on compatibility list it's 08-13 is250,350 & isf.
So this isn't compatible with 2006-2007?
It's same relay.
@@TunerwithKids
Really? 😲
Wonder why 06-07 are not
listed 🤷🤦
But thank you very much for the reply 👍
Mine stopped working on the headlight sides. The ones beside the wing are working. What would be the problem? I replaced all fuses today. And the flashers aren't working even in parking mode. The rear one works as normal
It’s the headlights signals if rear is working
@@TunerwithKids Thank for your reply? That makes sense. I checked Lexus UK owners forum and someone had similar issue. And his problem was fixed after he placed a resistor to the tail lights. I guess it happened a few weeks after I installed the new HCmotion tail lights. I will replace this relay this week and also replace all bulbs on my OEM head lights. Also I guess I will need to add a 6 Ohms resistor to the tail lights. Do you think that would solve the problem or do you think it something else? Thank you so much for all your vides, they are always so helpful
Thanks for the video. That white tab is no joke. Took me forever :). Btw…do you still notice a delay after the click like the other one? Thank you again!
No delays on this one. Perfect on at the tap. I like the tap to turn for lane changes.
How did u take out the white tab?
@@rivalelite5571 Take a needle nose plier and compress the clip from the back. Comes out much easier. Hope that works.
Can someone help me. I have after market headlights and taillights. So i have hyper flash only for the left blinker but the hazards are normal? Only half of the taillights flash on the back when I signal left. No issues when I signal right. Again no issues when I use hazards. How do I fix this and if I buy this would it fix it?
The relay will l
Take care of all of that.
Lexus CT 200h. Gdzie znajduje się przekaźnik i jak się do niego dostać?
Hi Binh, just bought the same headlights you have on your car for my car, a 2006 IS250. Question; do you think I need to (tap the blinker line) install resistors to prevent hyper flash?
Yea or use this relay.
@@TunerwithKids Thanks I was just doing my research.
@@doomsday_esc Hello did it work? I have 2006 IS and it looks completely different than the relay he's showing.
Is that relay the same as for a 2014 Lexus IS350? Also where can I get my front bumper repaired or should I go aftermarket
I think after 2IS, they used the BCM to do this so no more relays. Have to use resistors.
Hey bihn quick question would this relay work on the 06 is250? bcs on the amazon store it doesn’t say. Thanks man!
Yea. All Toyota relays are same.
I have hyper flash blinking only on the right headlight. Does this relay solve the problem or do I need to have a new resistance?
Yea it flash same regardless of resistance.
Yea it flash same regardless of resistance.
I installed it but now they don’t turn on the lights when I lacquer it or when I uncheck it.What can I do?
Idk, does hazards or turn signals work?
everything works fine except for the lacked special effect! before changing it the special effect worked!!
Check fuse to battery terminal. The animation starts when you unlock and signals blink 2 times.
Hello
I bought this relay and it doesn't fit.
It has eight pins and the original relay only has four pins
Wrong relay, on car side? You putting this in a Toyota?
Yes 2008 is250
Same flasher
yes I unhooked the wrong relay
I found it with the signals on. It was hiding next to it.
Also I bought some lights with the resistors built in. Kinda of expensive but easy. Thanks
Did you change the side mirrors turn lights?
Yea these are aftermarket covers with signal and running lights.
@@TunerwithKids oh gotcha, have you made a video on them before? I could only find the one u did for the sienna
Nope, I did them like 7 years ago before I started recording videos.
@@TunerwithKids Aw man, would have loved to know where you got them from though…
Good morning. I have vland headlights in my 2010 lexus is250 and my passenger signal light just started flashing white . Hope you could help me out
Sounds like a warranty issue. Board might be bad if the white is blinking with signals.
@@TunerwithKids ok thanx. It started back working fine then back to white🤦🏽♂️
How did you install those turn signal mirrors? Or did they come stock? I have an 07 IS350 that I'd like to get some turn signal mirrors on.
These are Taiwan cover replacements. ebay.to/3xuB3nt
@@TunerwithKids Thanks, will look into it. Keep up the great videos!
What can I do if only my left turn signal on my sequential taillights hyper flashes? It didn’t before but out of nowhere only my left turn signal started hyper flashing.I have vland front headlights and b/c sequential taillights.
Try replacing with LED relay.
@@TunerwithKids is that the same relay you installed?
Yes. Check links in description.
Hey man So I recently bought some vlands and the amber blinker only worked on one side and the other side was just flashing white. I figured it was the relay so i switched it out but after i switched it out all the blinkers on both the front and back stopped working along with the blinker arrows on the dash. Why could this be?
Relay not working. But the white blinking VLAND is a warranty issue.
I put it in the old relay back in and nothing changed. what do you think the issue is?
No idea. Unless fuse is out. What does hazards do?
@@TunerwithKids hazards stopped working as well unfortunately.
Something wrong somewhere with power or fuse. Cause hazards on separate relay or circuit.
do you still have lock/unlock confirmation?
Yea.
@@TunerwithKids Thank You!
How did you get you Dashboard to glow blue?
Check my other videos on that.
I like mirrors without turn signals more.
Where did you get your old flasher LED relay?
Should be in the video description links. It’s just an $8 or so Amazon relay for Toyota
@@TunerwithKids ok cool thanks
Thank you!
hey bro is that the relay for the starter as well?
No. Turn signal.
@@TunerwithKids question for you i installed leds on my tail lights of my lexus and the fuse relay keeps going out any ideas why?
You have a short somewhere or bad bulb. Put regular bulbs back?
Hi, does it work on oem without led as well??
Yes it just a relay that adjust the speed of signal regardless of load. Factory relay is designed per load to indicate a failed bulb.
Thanks a lot, much appreciated 🙏
Your video have been helpful, I just ordered one now. 2 months waiting period.
Two months for a relay??? Should be in stock on Amazon.
I didn't buy from Amazon, I bought from Aliexpress, found it cheaper there, they have stock but shipping takes longer. I have stuff which I bought back in April, still haven't arrived yet.
Thx bro
Hey I have a 2010 lexus Is. My set up is vland headlights and hc motion tailights. Recently I've been noticing the blinkers hyper flashing when the headlights are on. All the lights themselves work perfectly. The hazards work perfectly wether the headlights are on or not. Still running stock flasher module. Do you think it's also the flasher module and time to upgrade ???
update: fixed with the new flasher
@@prashundey4247 yoo! just got new lights today on my is 2010 too! my headlights and taillights have hyper flashing, but is normal with emergency lights. any suggestions?
@@emmanuelrodriguez1166 in what scenerio it hyper flashes is prolly irrelevant, as long as no bulbs are out. The led flasher relay should do the trick. Solved all my problems and the speed adjustment on it is helpful to.
I have a 2012 is350 se
Why does my car only come with one relay? It only came with the green one.
That’s correct, I left my old relay taped to the new one so I wouldn’t lose it.
2:13