Making a small grooved adhesive plate works really good too with super glue, but I like this idea even better because you can keep the nice surface appearance without worrying about the heat turning it while removing...
Mulțumesc frumos pentru cea ce ne inveti pe unii dintre noi Respect si admiratie Te rog daca sti spune mi cum fac un nut de pana la interior pe strung Mulțumesc încă odată
Вот именно для этой цели я сделал маленькую проточку на кончиках кулачков. И теперь любая шайба толщиной свыше миллиметра легко зажимается прямо в кулачки.
У профессионалов два, три,четыре десятка комплектов кулачков (пропорционально стажу работы) под различные операции, гаражные хоббиты могут только мечтать о таком изобилии .
As a time served machinist I must tell you that you are only half right. what you missed is that you need to mark your fixture at number 1 chuck jaw so that you can put your fixture back in the chuck in the same place that you machined it every time to keep concentricity.
Hi, you're right! However, this is just an example, so I didn't want to waste too much time with the details... In any case, I thank you for the comment which may be useful for users.
I could tell you how, you need to make several out of shim stock, finish the ID while holding on the OD then do not unclamp and put a bolt through the ID to hold while you remove the OD clamp or bolts then finish the OD
An elegant solution , however just superglue the washer to the ends of the jaws ( it helps if the jaws are clamping something) , the washer doesn’t as a rule need to be concentric , hold it in place for a few moments with something in the tailstock , good enough for rock and roll .
Es un antiguo recurso, usado por torneros para fabricar golillas (washers), también se le conoce como "camisa partida" (clamp). Generalmente se fabrica de bronce, material que es más "blando" y rápido para tornear.
Ciao, hai ragione... Ma cerca di immedesimarti nel hobbista che vuole ribassare una singola rondella, pensi davvero che comprerà un set di morsetti teneri per quel lavoro???
Great idea! Simple, inexpensive, quick and works very well.
Fantastico.... sempre cose interessanti nel tuo canale
AWESOME!, GOOD IDEA. THANKS.
That was beautifully done and such an incredibly useful technique
Amazing video
Great idea, I shall store that up for future use.
Excellente idée. Je suis abonné à la chaîne et j'apprécie beaucoup. Merci 👍👍👍👍👍
Thank you for sharing this great technique.
Bravo Türkiye den selamlar 🎉
Molto interessante bravo
muchas gracias MAESTRO
¡Excelente! Felicitaciones.
That's good 👍 👍 👍
You are doing unique work
Sehr sehr gute Idee.
Vielen herzlichen Dank. Mfg.Lothar aus Haburg
Thank you so much sir for this new idia
Very nice work.
تحياتى لك.. افكار ممتازه ومحتوى القناه مفيد
😀 tres tres bonne idees merci
Magico! 👍👍👍👍👍👍😎😎💚💚🤗🤗
Making a small grooved adhesive plate works really good too with super glue, but I like this idea even better because you can keep the nice surface appearance without worrying about the heat turning it while removing...
elegance is in its simplicity.
Mantap bos.👍👍👍
And if you use the version with a shoulder against the chuck it gives you a repeatable reference for multiples.
Уровень ПТУ 😅😅😅😅😅
Ciao, sempre ottimi video! è un pò di tempo che ti seguo, hai anche una pagina fb e/o instagram?
Ciao, ti ringrazio... Al momento ho solo il canale youtube, comunque non escludo la possibilità di creare qualche pagina su altre piattaforme!
You know the weirdest thing about watching these videos and knowing what everything feels like in your head.😂
Bravo!
Gracias ahora si me dejaste anonadado lo pondré en práctica 👍
Mulțumesc frumos pentru cea ce ne inveti pe unii dintre noi
Respect si admiratie
Te rog daca sti spune mi cum fac un nut de pana la interior pe strung
Mulțumesc încă odată
Вот именно для этой цели я сделал маленькую проточку на кончиках кулачков. И теперь любая шайба толщиной свыше миллиметра легко зажимается прямо в кулачки.
👍👍👍
Профессионалы так не делают, для этого существуют сырые кулачки с выточками... Но для гаражных хобистов пойдёт!
У профессионалов два, три,четыре десятка комплектов кулачков (пропорционально стажу работы) под различные операции, гаражные хоббиты могут только мечтать о таком изобилии .
Awesome technique. How to made a ring from Teflon with a thickness of 1mm and a diameter of 35mm, dephth - 5mm.
Laudetur Iesus Christus 👍👍👍 Deo gratias 👍👍👍
🎉💪💪💪👏👏👏
As a time served machinist I must tell you that you are only half right.
what you missed is that you need to mark your fixture at number 1 chuck jaw so that you can put your fixture back in the chuck
in the same place that you machined it every time to keep concentricity.
Hi, you're right! However, this is just an example, so I didn't want to waste too much time with the details... In any case, I thank you for the comment which may be useful for users.
Метод рабочий! Но также для этого можно использовать токарный патрон меньше и сделать на нем микро выточки в кулачках
смять шайбу можно, приходится осторожничать , а в оправе она плотнее сидит, не пережмёшь, особенно медяшки
saludos vean y aprendan
That's very good. I wonder how to make a .002in washer/spacer
I could tell you how, you need to make several out of shim stock, finish the ID while holding on the OD then do not unclamp and put a bolt through the ID to hold while you remove the OD clamp or bolts then finish the OD
👍👍👍❤
An elegant solution , however just superglue the washer to the ends of the jaws ( it helps if the jaws are clamping something) , the washer doesn’t as a rule need to be concentric , hold it in place for a few moments with something in the tailstock , good enough for rock and roll .
This is what soft jaws are for and do. A lot of these 'simple hacks' are unnessesary with a set of soft jaws used correctly
Es un antiguo recurso, usado por torneros para fabricar golillas (washers), también se le conoce como "camisa partida" (clamp). Generalmente se fabrica de bronce, material que es más "blando" y rápido para tornear.
Would you call this a split collet ?
Guarda che esistono i morsetti teneri, per fare queste cose. Comunque anche il tuo metodo e' valido, anche se molto macchinoso.
Ciao, hai ragione... Ma cerca di immedesimarti nel hobbista che vuole ribassare una singola rondella, pensi davvero che comprerà un set di morsetti teneri per quel lavoro???
Would have liked to finish video, but couldn’t because of the irritating music😢
so simple, i feel stupid
I guess you mean facing off!
Non facevi più subito a fare la rondella?
try making them out of steel.
А что такое-опустить шайбу?
Возможно уменьшить высоту ( толщину) шайбы?
How do you "lower" washers? Wrong word.
Hi, sorry for my bad English, what is the right word?
это если их 100 штук надо. из за одной не будешь делать
Древний способ ! Старо как мир !!!
Уважаемый! Не все такие древние как Вы! Молодые начинающие "наркоманы"металлообработки имеют право знать и древние способы камлания с металлом.😊
What a waste of my time..
Se for muitas arruelas de diametros diferente aja matérial.
Primero aprende a hablar, girar????