Thanks to this video and you I was able to solve a red light problem. I have a denon avr-x3100w receiver, I am not a technician, just a man curious about electronics, guide me with your video and I disassembled it with a multimeter, everything you did, I checked cold welds, I measured the power supply with a multimeter, everything like you did it in your video but now I need your help I managed to turn on the receiver now it doesn't turn off but I have a problem that I don't have HDMI or audio I was able to realize that I only have audio in FM and zone 2 when I connect via RCA from my smartphone but in the zone main I do not have audio or hdmi gui I do not have a denon interface I do not know how to interpret the schematics because on the internet there is a service manual for the receiver in your experience I must change pc9211 panasonic mn864771 it is as if the entire hdmi pcb card was disabled there are too many stages I could receive some advice from you if I could, the Denon receiver sent it to you but I'm from Mexico.
It is worth mentioning that there are special modes (buttons) that the receiver itself gives you information. It seems that the main microprocessor displays all the information of number and version gui s/n model package number of main the receiver displays the information in the same receiver it is like if a part of the entire digital card was dead
The denon application does not recognize the receiver I do not have a gui interface or also called user interface Even so, without being a technician and with your video I was able to solve this problem of the red light, the fault was in the amplification stage, damaged darlihgthon sanken transistors, we replaced them, it returned to normal but now there is no sound in the main area and no hdmi
In Mexico there are no longer electronics that fix stage by stage component by component, the majority says if your digital pcb is damaged in one component you have to change it all like you, there are only a few left, congratulations
hi Angel Ramiro Mar Flores, thanks for mentioning your valuable cmt. do not attempt to change mn864771 ic without knowing the fault. but you can change the pcm9211 ic but before that their is a way to check the pcm ic and MN864771 ic. 1. connect optical input and check whether it is detecting the input audio signal format. if its detecting the signal then PCM9211 ic is good condition and do not change it. 2.to check mn864771 ic .first connect hdmi input and output then check ic clock signal and (clk,scl,sda,...)and check its digital output pin and also check reset pin and en pin from ucom ic. then check dir ic comunication status. everythink seems good as per manual then ok or else first replace mn864771 ic and then update the firmware then check . i hope its fixed . or else just proceed to check with technician or replace the hdmi board.
i don't think its worth because special button is only for service personal . for service purpose . in case normal user don't know it properly then it may cause some firmware damage and disabling the board features.
Excellent video ! I have a Denon x2600H , which had a fall . So now its turning on and I can hear 2 relay clicks 4 seconds apart and video and all functions work as expected. Except there is no sound at all. No test sound , no heaphone sound , no speaker sound from any input or network music. Because of the fall I am guessing it might be cold solder joints , but wanted to hear your oppinion. Might it be defective audio chip or the DAC section ?
Hello, I have the same failure on a x3100w. I don't understand English in the video, did you replace the transistors? we don't see what you are replacing in your video. Thanks a lot
standby is the common symptoms for avr .we have to spot out the faulty components and fault may have anywhere in the avr and need to checking it properly to solve this issue, please try to identify the fault by stage by stage.
Hi sir i have Philips HTS5530...now i faceing standby problem...a standby light is not opening... when i remove the loder wire from main board... Standby has opens...i chang a loder..but not cure... then i replace all capacitor for loader section...not cure...I think open & closing ic is fault.. A ic name is Am5888...pls give any suggestion....pls reply🙏 thank you...
Hello .. sir i have denon avr x3100w it has video and audio problem firmware shows system is perfect but it doesnt work anything .. but firmware pakage version shows 0000.. can you help me sir?
Super bro. From Andhra. My denon also issue automatically switch offing and bands changing, remote some times not working. Rarely red light issue. What is the reason?
Basically all AVR have own special features , First do verify your budget scale and search for suitable AVR then share the shortlisted avr and I'll tell you the good one
I am new to avr, I do have jbl amp with micca speaker for for 2.1 setup. I want to go next level. My budget is pritty low. Max 30k for receiver. In amazon I can seen htr-3072 and yht-1840. I am not happy with the speaker and woofer package that comes along with that, it's plastic and tiny speaker. Pls suggest a option. Bec I would like to hear from technician rather than other critics.
Hello, I have a Denon s910w, it does not output audio or video, what could it be? any indication? firmware? dac? I would appreciate your help, I would send you the HDMI plate for you to repair it, but I am on the other side of the world, in Peru, South America, can you give me some tips? I know something about electronics
I have a denon x2000, it works for sometime (some days it works for an hour or so, some other day it works for 15 minutes) then suddenly it goes off and on in a cyclic fashion, then it works for few more minutes and the problem happens again. This is happening then and there. Do you know how to fix it.
Denon 4311CI DSP 01 error, in need HDMI board.. I need service support, kindly guide me how to solve this. Audio out not working(display left side analog or HDMI logo not appear based on the( I/P) rest of the things good.
No need to be Reprogram the ic just replace the ic and perform db update using advanced menu. Follow the service manual and owner manual for advanced menu buttons
Sorry for the delay, now only I got smd rework station from my office after release lock down. I replace the DSP 1 IC and initially it shows audio signal after power recycle the same issue occurs again. I try to find the manuals no database update (advance setting) procedure found. Please guide me how to fix this..
NEVER EVER SHUT DOWN THE STEREO RECEIVER WITH THE REMOTE CONTROL IF IT HAS ONE ALWAYS USE THE MAIN POWER BUTTON TO PREVENT THE RECEIVER BEING LOCK UP IN STAND BY MODE FOREVER ####
நீங்கள் சொல்வது உண்மைதான் இது போல்ஏவி ரிசிவர் சர்விஸ் சானல்கள் அதிகம் இல்லை...தமிழில் நல்ல முயற்சி தொடருங்கள் வாழ்த்துக்கள் நண்பா
Thank u bro ☺️
இன்று தான் உங்கள் சேனலை பார்த்தேன், மிகவும் அருமை......
Thank you 😊
சூப்பர் சார் நான் வீடியோவை லேட்டா பார்த்து இருக்கேன் மதுரை பிரதர்
Good information for technician, pls tell some tips about how to protect and safely use av reciver for beginners....
Sure I will
Thanks to this video and you I was able to solve a red light problem. I have a denon avr-x3100w receiver, I am not a technician, just a man curious about electronics, guide me with your video and I disassembled it with a multimeter, everything you did, I checked cold welds, I measured the power supply with a multimeter, everything like you did it in your video but now I need your help I managed to turn on the receiver now it doesn't turn off but I have a problem that I don't have HDMI or audio I was able to realize that I only have audio in FM and zone 2 when I connect via RCA from my smartphone but in the zone main I do not have audio or hdmi gui I do not have a denon interface I do not know how to interpret the schematics because on the internet there is a service manual for the receiver in your experience I must change pc9211 panasonic mn864771 it is as if the entire hdmi pcb card was disabled there are too many stages I could receive some advice from you if I could, the Denon receiver sent it to you but I'm from Mexico.
It is worth mentioning that there are special modes (buttons) that the receiver itself gives you information. It seems that the main microprocessor displays all the information of number and version gui s/n model package number of main the receiver displays the information in the same receiver it is like if a part of the entire digital card was dead
The denon application does not recognize the receiver I do not have a gui interface or also called user interface Even so, without being a technician and with your video I was able to solve this problem of the red light, the fault was in the amplification stage, damaged darlihgthon sanken transistors, we replaced them, it returned to normal but now there is no sound in the main area and no hdmi
In Mexico there are no longer electronics that fix stage by stage component by component, the majority says if your digital pcb is damaged in one component you have to change it all like you, there are only a few left, congratulations
hi Angel Ramiro Mar Flores, thanks for mentioning your valuable cmt.
do not attempt to change mn864771 ic without knowing the fault. but you can change the pcm9211 ic but before that their is a way to check the pcm ic and MN864771 ic.
1. connect optical input and check whether it is detecting the input audio signal format.
if its detecting the signal then PCM9211 ic is good condition and do not change it.
2.to check mn864771 ic .first connect hdmi input and output then check ic clock signal and (clk,scl,sda,...)and check its digital output pin and also check reset pin and en pin from ucom ic. then check dir ic comunication status. everythink seems good as per manual then ok or else first replace mn864771 ic and then update the firmware then check .
i hope its fixed . or else just proceed to check with technician or replace the hdmi board.
i don't think its worth because special button is only for service personal . for service purpose . in case normal user don't know it properly then it may cause some firmware damage and disabling the board features.
நல்ல வேலை சூப்பர்
Super sir tamila sonna vetham simply super
Excellent approach.👍🏻👍🏻👍🏻
Super sir.great effort.lets do continuously
Thank u ☺️
Excellent video ! I have a Denon x2600H , which had a fall . So now its turning on and I can hear 2 relay clicks 4 seconds apart and video and all functions work as expected. Except there is no sound at all. No test sound , no heaphone sound , no speaker sound from any input or network music. Because of the fall I am guessing it might be cold solder joints , but wanted to hear your oppinion. Might it be defective audio chip or the DAC section ?
i dont thing your amp have cold joints or dry soldering . fault may be in dsp section because all other functions are working
@@fixavreceiver hii sir
aapka fin no mil skta h
Hi bro
Hello, I have the same failure on a x3100w. I don't understand English in the video, did you replace the transistors? we don't see what you are replacing in your video. Thanks a lot
standby is the common symptoms for avr .we have to spot out the faulty components and fault may have anywhere in the avr and need to checking it properly to solve this issue, please try to identify the fault by stage by stage.
Amazing video sir i can't words
Brother I have denon avr x 2400h
I am facing same problem ( red light blinking ) please give your valuable suggestions
please chat with me in whatsapp
Bro same problem avr 3100w red light blinking bro give your voluble suggestion
This model is good to music???
Thanks nanpa explain way is good simplest good ok
Super bro
Keep it up
Vazthukal
Bro, neenga endha oor? Ennoda denon amplifier same problem.
Vellore
Excellent Job Bro👍👍👍👍👍
Thanks ✌
Hi sir i have Philips HTS5530...now i faceing standby problem...a standby light is not opening... when i remove the loder wire from main board... Standby has opens...i chang a loder..but not cure... then i replace all capacitor for loader section...not cure...I think open & closing ic is fault.. A ic name is Am5888...pls give any suggestion....pls reply🙏 thank you...
Please contact me in whatsapp 9943124215
Namastay sir my av reciver 3100w same problem sir how is it my reciver problem sir
For this kind of models you need to check step by step method only
super Sir good working Tamil
Thank ji
Hi
My new avr X2700h has been problem cbl/sat resolution input 1080p, but avr input show resolution 720p. Please help me.
Set avr resolution in auto mode
Hello .. sir i have denon avr x3100w it has video and audio problem firmware shows system is perfect but it doesnt work anything .. but firmware pakage version shows 0000.. can you help me sir?
its not a firmware issue. please check in HDMI board for defective components.
@@fixavreceiver thanks .. i will check again
HDMI board purchase cheyyan kittumo
Model
@@fixavreceiver denon 1612
Super work bro
Excellent . Please share your name and contact details at the end of each video presentation . Also share the details in your channel description .
Okay thanks u sir
Super brother Good job
Thank you so much
Can you provide denon avr1713 flex ribbon cable both hdmi and motherboard, please reply soon
Price and payment mode
super bro.. kindly share your shop location bro..
Vellore, tamilnadu, India
@@fixavreceiver vellorela yanga bro im from chennai
Vasanthapuram, near nerthaji stadium and police quarter
@@fixavreceiver ok bro..
Super bro. From Andhra. My denon also issue automatically switch offing and bands changing, remote some times not working. Rarely red light issue. What is the reason?
👍
@@fixavreceiver bro where u from?
I am in Vellore, tamilnadu
@@fixavreceiver how solve my issue bro? Original spare kadikuma?
Bro , bring it to me we I'll check it like full check up
Pl make video in English so that everybody can understand very well
ok bro
Hi, I am planning to buy a avr, what brand would u suggest, shall I go for assemble set or branded one. Pls suggest
Basically all AVR have own special features , First do verify your budget scale and search for suitable AVR then share the shortlisted avr and I'll tell you the good one
Don't go assemble set .u won't get satisfaction from it and money also High for Full package
Or else buy used AVR from trustable source
Thank u so much for all ur comments. I fully agree with you.
I am new to avr, I do have jbl amp with micca speaker for for 2.1 setup. I want to go next level. My budget is pritty low. Max 30k for receiver. In amazon I can seen htr-3072 and yht-1840. I am not happy with the speaker and woofer package that comes along with that, it's plastic and tiny speaker. Pls suggest a option. Bec I would like to hear from technician rather than other critics.
Super technician
👍
In which area your service center is located
Vellore,tamilnadu
Hi. Can you repair my avr onkyo txsr 508
Yes sure please send it to me I'll fix it
Great job ❤❤❤
7.2 avr entha brand best bro?
Denon, marantz, Yamaha
Super sir... U r the great... Thank u
No, just to explore the service
Very nice sir
Super
Denon PMR 480
Left and right ,right balance is not working sir .
Can you solve it please .
Sure, I can fix it
Sir contact number please .
9943124215
I have denon avr1513 same problem what I will do?
Chat with me in whatsapp
@@fixavreceiver ur whatsapp number plss
9943124215
@@fixavreceiver bro I can't find in whatsapp.
Why
Super broo 👏👏👏
Thank u
@@fixavreceiver bro contact number
9943124215- whatsapp also same
Video super bro
Awesome 👍😎
👍
Nice. Good job.👍
Okay thanks bro
Good work bro
Super video.
Thank u 😊
Sir ennoda denon Avr x2000 no video out problem sir . Service center la hdmi Board mathanunu solranga. Ungalala service panna mudiyuma
Sure please contact me at 9943124215
2 aux use pannanlum 7.1 channel effect Varuma sollunga bro
Its depends upon your AMP, proligic option, or high end AMP required or else use analog to digital converter
@@fixavreceiver bro benon x2700h vakanum bro atha kekura
Bro stereo connection panna 7.1 Varuma bro
@@fixavreceiver pls sollunga bro
Hello, I have a Denon s910w, it does not output audio or video, what could it be? any indication? firmware? dac? I would appreciate your help, I would send you the HDMI plate for you to repair it, but I am on the other side of the world, in Peru, South America, can you give me some tips? I know something about electronics
Check main ic and it's RAM
Sir denon 1312 speaker line laa some disturb sound ad odana red light mode vanthu off akathu sir so I need service
Ok I can fix it easily
Please contact me in this no 9943124215
@@fixavreceiver thank yo sir morning I'll call yo
Second hand av receiver vangalama, unga kita kidaikuma sir
If it's in good condition and untouched u can buy
I doing only service , if any customer wants to sell the AMP that time I share the AMP details to who wants the AMP
Currently I don't have any amp for sale
Thanks sir
Nice jii good work
☺️
I need 5.1 AV receiver, please suggest good brand in below 35k
please buy denon avr for latest features and last long compare to other brands
My denon has same problem how do i solve ir
Pioneer 933 are keen 8ohm speaker connect cheyav
Speaker wattage ?
Denon 3311i power on problem your contact details plz?
9943124215-whatsapp also same
intha faultuku evalo charge paninnga with service charge?
1k
Hai myself murthy from mumbai
I need ur help pls no sound from the system waiting for ur reusable reply
Good job
Thank you 😊
Av receiver vs amplifier oru video podunganna...
Ok bro soon I post video about ot
Bro stereo connection panna 7.1 Varuma bro
Its truly depends on your AMP bro . If ur using branded AVR u can get 7.1 sound from stereo input through proligic mode/Dolby digital mode
Super Sir
Thank you bro
I have a denon x2000, it works for sometime (some days it works for an hour or so, some other day it works for 15 minutes) then suddenly it goes off and on in a cyclic fashion, then it works for few more minutes and the problem happens again. This is happening then and there. Do you know how to fix it.
Hi, as per ur comment ur AMP stuck in thermal overload
Please clean dust and dirt in digital board and amp board it is causing this kind of fault
@@fixavreceiver I had vacuumed it but still it happens. Can you please suggest any points to check in the board. Also where are you located
If u can please send it to me I'll fix it
I am from vellore, tamilnadu
Super macha. Malayalam theriyumo.
No bro
But I understand
Hello sir my denon AVR red light blinking problom
chat with me in whatsapp
Super bro
Denon 4311CI DSP 01 error, in need HDMI board.. I need service support, kindly guide me how to solve this. Audio out not working(display left side analog or HDMI logo not appear based on the( I/P) rest of the things good.
DSP 1 ic need to replace alongwith it's corresponding RAM IC
@@fixavreceiver I've spare IC how to I reprogram?
No need to be Reprogram the ic just replace the ic and perform db update using advanced menu. Follow the service manual and owner manual for advanced menu buttons
@@fixavreceiver Thank you.. I try to solve
Sorry for the delay, now only I got smd rework station from my office after release lock down. I replace the DSP 1 IC and initially it shows audio signal after power recycle the same issue occurs again. I try to find the manuals no database update (advance setting) procedure found. Please guide me how to fix this..
സൂപ്പർ
Thank you
❤❤❤🎉
Anna . Sony iv300. (Or) yamaha yht 1080 ethu nalla irukkum 35000 rupees la
Yamaha for use also good and resale value is higher than Sony iv300
My denon x4000 also have same problem when I play music long time it's going standby and blinking redlight
Now my AMP one hour on nothing happening when connecting speakers only I face this problam
Ok, chat with me in whatsapp
@@fixavreceiver get me your whatsapp no pls
9943124215
What's the service charge for this amp
1k
@@fixavreceiver sir how to contact you your mobile numper plz
And the problem was.....???? Bad solder joints?
In this perticular unit yes only bad joints
❤
Nice
Thank u ❣️
Open service center in chennai
👍😊
👍🏻
start an online repairing course
👌🤝🤝🙋
Thank bro for first comment
Marantz sr5005 modal not audio walking
No sound in yamaha crx 040
8.56 tamil la videos illa bro indha madhiri la
Yes bro. , That's why I'm trying to explore
Keep it up your work 👍 it's useful many
Thank u and I will
👍🏻👍🏻👍🏻👏👏👏👌👌👌
NEVER EVER SHUT DOWN THE STEREO RECEIVER WITH THE REMOTE CONTROL IF IT HAS ONE ALWAYS USE THE MAIN POWER BUTTON TO PREVENT THE RECEIVER BEING LOCK UP IN STAND BY MODE FOREVER ####
😃👌🤝🤝
👍
Hi
hi bro
சர்வீஸ் சென்டர் எங்க இருக்குன்னு
Enna uru na niga
Vellore, tamilnadu
No parfekt
உங்ககிட்ட விலைக்கு ஆம்பிளிபியர்இருக்க
Currently no AMP bro all sold
Good work
Thank you so much 😀
Super Bro ❤️
Hi
hi