Arduino Project - Smart Street Lighting Project Using Arduino
Вставка
- Опубліковано 9 лют 2025
- This arduino project explain about smart street light system using IR sensors and LDR.
Light Detecting Resistor is useful to detect light or darkness as its resistance is varying according to the light intensity. I have used IR sensor to detect the vehicle so that Light will be turn ON only if there is a night and vehicle is present at IR sensor.
Please Share and Subscribe "Hiren Tailor" :
bit.ly/3c7zcax
Code and Interfacing Diagram:
github.com/hir...
Arduino Tutorial Playlist:
• Arduino Projects and C...
My Facebook Page: / hirentailorec
#ArduinoProjects #SmartStreetlight #LDR
sir i want resistor values?
220 ohm
@@ecit sir near led 220 ohm resisitor but near ldr which resistor is used?
@@sudeepp8722 you can use 1k ohm or any resistor between 1k ohm to 10 k ohm
@@ecit Thank you so much sir.
@@sudeepp8722 most welcome
*Sir can i know which software is used to run the code?*
Arduino IDE, you can watch first video of Arduino Project Playlist on my channel
@@ecit thanks for the response.
Codeful and Helpful 😀
Thanks 😄
v.helpful
@@markrrrober Thank you!
Thank you for useful video sir 🎉
Most welcome
What are the equipments required for this project?
@@AbhishekKumar-k3l9v Arduino Uno, IR sensor and detail circuit diagram link is mentioned in the description
sir , this video shows the hardware of smart street light and its connection with webapp ?
@@zuhaanabeel2445 this is not connected with web, if you want to do it use ESP32 and use Webserver with it
Sir is there any specific wires that we should use pls reply sir I have to submit this project
@@dhivyadharshni1314 There is no specific wire required because here only few mA of current is flowing through the wire.
Sir my IR sensors are starting with a on condition where the light is keep on glowing in the out pin as well what could be the problem? And also I am using 1k resistor for the ldr sir is it ok? I have the same IR sensors that u have shown in the circuit diagram sir still I didn’t get the output
Sir pls help me out I have to submit this project tomorrow pls sir even when my IR sensors both are working in on condition the led is not glowing
@@dhivyadharshni1314 you need to vary the resistance with LDR, adjust the value according to light intensity you want to set, log your data on serial port and see if you are getting correct data or not
@@dhivyadharshni1314 are you using same code which I have shared in description link?
Can we use only LDR sensors here?
@@PritiMane-ov5pm I have already used LDR for light detection
@@ecitSir I am doing the same project as I am a diploma student I want the circuit diagram for the project and I am taking reference from your video I just want to use LDR sensors and IR sensors what will be the circuit diagram for that is my question
@@PritiMane-ov5pm circuit diagram link is mentioned in the description alongwith the code
Sir, if we want to use a 9w led bulb then what is the change in circuit???
Go through this video ua-cam.com/video/F5zoG9IOZNE/v-deo.htmlsi=YYX9A6DQrCkJ9jN9
You can merge two projects
Can we make this project wireless? By using Bluetooth or WiFi to transmit signal from Arduino to the sensor?
Yes you can, You may use ESP32 or ESP8266 to transmit data using WiFi or BLE.
@@ecit thankyou so much, can you please share the code/ working module if you have any using Bluetooth/WiFi
@@sachinshinde7159 It may take time, I will share the code after 2-3 weeks.
Very nice explanation sir! Thanks for this video. I want to ask that can we do this using raspberry pi?
Yes you can, you need to write python code for it.
Thanks for replying
Sir what is the software that you used for the circuit diagram bcs I need it as the same way pls explain
@@dhivyadharshni1314 you can use following link for circuit diagram design www.circuito.io/
what is the type of the arduino? is this uno re3 or rev2 ? or what ? pls
Rev3
@@ecit thank you
Sir u have used three wires to connect ,instead of those we can use jumper wires
Sir,can we use the same circuit diagram and code for Arduino nano?if not,please share the diagram and code sir.
You can use same for the Nano also
It is not coming sir
Once check email sir
which port should be selected for compiling the code?
You need to select Arduino Uno port, you can find from device manager or by removing the USB connector and see which port has removed from the list
Hello sir the coding can use 5 sensor?
You need to modify the code for 5 sensors, you need to add additional pins in the code
Can you tell about backend and frontend
Frontend and backend of this project or in general?
very helpful video sir ,can u please share the links from where to buy IR sensons ,ARDUINO,LED's,BOARDS 👏👏
You can buy everything from Amazon or local electronics shop.
Sir, In my case only one IR sensor is working. Can you help me out please?
@ECIT Engineering, yes sir you should help him out
First replace the IR sensor with working IR sensor, and make sure that both IR sensor are working.
Check the pin number in code and board.
Make sure wire is okay.
I have other queries as well. Where can I contact you?
@@rollndope5568 hirentailor.rf@gmail.com
Sir here my output is showing correctly in serial monitor but not correct output
My problem is both the led are glowing when brightness is less than 100 , what is the problem sir when there is no object near sensor
You may need to adjust the brightness constant in code ( update LDR value)
Superb
Thanks 😊
If by adding one more led and one more IR sensor does it works
Yes it will work, but you need to change the code
@@ecit By placing the connections in the code is it right sir
@@vikithayarlagadda8981 yes, you need to connect remaining pins and then also add code for it.
@@ecit thank you sir
@@vikithayarlagadda8981 most welcome
How much does it cost? If we add Solar panal and battery for storage?
Around 1000 Rs.
If in this case sir, if we add solar panel and battery, do we still need to include it in the code?
bro did you made this project?
Sir ,can u pls make prototype(model) for this
It will be useful for us
What kind of prototype you want?
We have to make automatic street lights project
So,we have to make a mini street lights
@@bhavanik188 that you can build by yourself
Tq sir
Sir,when we made our prototype
IR sensor functionality was reversed
Lights are always ON ,when we keep an object they were OFF
sir dark ke condition mai jab light ON hoti hai using ir sensor
phir jab ir sensor se object remove karte hai toh light off ho jati hai toh mai yeh poochna chahta hu ki jab light off hogi toh ussme delay kese layege matlab jab object remove karte hai toh light off karne mai delay kese layege
code mai kya change karege plz btayege
In code, on line number 41 and 48 there is delay(2000); instead of this you can increase the delay to 5000 ( 5 seconds ) or even higher value
my LEDS are starting with the ON status...what could be the problem????
Are you testing this in night or in dark environment? Give light on LDR.
And verify your connection again.
@@ecit yeah i tested during night..i will test during the day..thankyou @hiren
@@simonkioko9384 most welcome and don't forget to subscribe this channel
led is how many volts?
3.3V or 5V
sir can we make it as, if the ldr value is less than 100 then the led will glow but in less and if the object is in front of ir sensor then the led will glow in high brightness for a specific delay
Yes you can, use any pwm pin of Arduino and set threshold as 100 in code
When ldr is below 100 write pwm value for brightness of led, if it is more than 100 then set high or 255 as pwm value for led pin
sir my Arduino uno 390 is not functioning in the app
Which error it shows? Can you share the link of your Arduino board?
@@ecit the code is compiling but showing error in saving to Arduino
@@akayt2608 may be you have not selected correct COM port for Arduino
@@ecit port's option was not available
@@akayt2608 you can verify about the driver, install FTDI drive support.arduino.cc/hc/en-us/articles/4411305694610-Install-or-update-FTDI-drivers
very helpful, however found a compilation Error on : "LDRValue not declared"
int LDRValue;
Must be declared in your code.
Sir I am trying to upload the code but the code was not uploading... I am trying several time but it was comipled but not upload
Which error it shows? Make sure that you have selected correct COM port and board before uploading the code
sir can we make this without Arduino?
Do you means without any microcontroller?
You can use comparator IC and logic gates to implement this without Arduino or Microcontroller
@@ecit i have all the components but i dont hava an Arduino Uno....can i make an direct circuit connecting LDR Led and IR sensor....so that in dark the ldr will pass the electricity to motion sensor..and motion sensor will only pass the electricity when it detects motion ...like this
@@harisbashir7287 yes it is possible but in that is it work like,
If there is darkness LED will not glow if LDR resistance is high enough,
And If there is light on LDR, it will reduce the resistance and allows LED to glow, however LED will remain turn ON only during IR sensor remains High.
@@ecit can u like share an circuit diagram plz 🙏
@@harisbashir7287 I think this link will help you, www.engineersgarage.com/making-a-light-detector-using-ldr-circuit-diagram/
Instead of +9V connect IR Sensor Output and make ground common
and if is there any way to implement all these things without using these physical equipments then please tell sir how to do so.
You can try proteus software
Do they glow automatically at the night time??
Yes, If there is a darkness near the LDR than LED will turn ON based on our threshold value.
Sir how to keep the object near to IR sensor in tinkercad software
I don't know, but I don't think that you need to put an object in software, only you need to change IR sensor value
Only 1 blub is working sir, also I have to run code every time I put object
Verify your connections from circuit diagram, make sure the LEDs are in series
where can we we find the inbuilt code?
I have provided the code link in description
int IR1 = 2;
int IR2 = 3;
int LED1 = 5;
int LED2 = 6;
int LDR = A3;
void setup()
{
Serial.begin(9600);
pinMode(LED1, OUTPUT);
pinMode(LED2, OUTPUT);
pinMode(IR1, INPUT);
pinMode(IR2, INPUT);
pinMode(LDR, INPUT);
digitalWrite(LED1, LOW);
digitalWrite(LED2, LOW);
}
void loop() {
int LDRValue = analogRead(LDR);
Serial.print("sensor = ");
Serial.print(LDRValue);
delay (500);
if (LDRValue > 100)
{
digitalWrite(LED1, LOW);
digitalWrite(LED2, LOW);
Serial.println("It's Bright Outside; Lights status: OFF");
}
if ((LDRValue < 100) && (digitalRead(IR1) == HIGH))
{
digitalWrite(LED1, LOW);
Serial.println("It's Dark Outside; LED1 Lights status: ON");
}
if ((LDRValue < 100) && (digitalRead(IR2) == HIGH))
{
digitalWrite(LED2, LOW);
Serial.println("It's Dark Outside; LED2 Lights status: ON");
}
if ((LDRValue < 100) && (digitalRead(IR1) == LOW))
{
digitalWrite(LED1, HIGH);
Serial.println("It's Dark Outside; LED1 Lights status: ON");
}
if ((LDRValue < 100) && (digitalRead(IR2) == LOW))
{
digitalWrite(LED2, HIGH);
Serial.println("It's Dark Outside; LED2 Lights status: ON");
}
}
this is correct code for this
Leave print statements , code is right , use this for that above circuit
Sir reverse operation is taking place
What exactly happening?
@@ecit The lights are on at the beginning and when the obstacle is detected it turns off
@@imagineimaginators518 okay, I will update the code on the github.
You can check it after 5 hours.
@@ecit Sir please tell me what changes should I make because I have to submit it today
@@imagineimaginators518 okay, I will send you code here..
can you send the base paper of the project
I don't have any base paper
How to connect wifi module to the setup ?
Which module do you want use? You may use ESP 8266 for this.
Sir is it program run in tinkercad
I don't know
Yes
How to add Solar Panel and battery on it?
Use solar panel to charge the battery and provide power supply to Arduino from the battery.
You need higher voltage at solar panel (let say 12 v) than battery voltage (5V),
You may also need charging IC or boost converter to charge the battery.
I hope this information will help you to get on right path to achieve your goal.
@@ecit where to attach the power in Vin?
@@kingjb9990 yes, you can use Vin and GND
@@ecit sir I have a problem, once the IR sensor detects motion, the lights will off, it works but it reversely operates. Also one thing, the lights lit up automatically and sequentially lits up even no motion detected.
@@kingjb9990 which code have you used? Are simulating this or testing with real hardware?
sir can u help me with the project
Which problem are you facing?
sir which arduino uno model should i buy and what is the price?
@@vasanthv4233 you need to buy Arduino Uno R3 board. amzn.eu/d/4FqyEYH
Or
amzn.eu/d/5eejw8p
Sir I am going to make this project with 6 led lights and also I am going to use solar pannel and recharge the battery and can u suggest me which led light( in Volt) and which amount of rechargable battery should I buy?
@@vasanthv4233 ua-cam.com/video/NLgYfyAp_Rg/v-deo.htmlsi=_AiH1HsUEkAKfran
This video will help you to calculate LED resistor, also make sure that you select correct watt of resistor. First go through this, prepare your own component list and I will verify it.
Please tell resistors values
Sir.
Resistor with LED is 220 ohm and with LDR you can use 1K to 5K resistor depending upon light intensity you want to set
With LED means near the LED
@@shaikamrin6497 yes resistor connected in series with LED
Sir code showing that no upload port provided
Would you provide link for IR sensor
I have used custom board, you can use buy any IR sensor.
Sir g please help me to make this project
You can ask me your questions here
Sir my ir sensor is not detecting object but it the led on ir sensor is glowing how to overcome this. The theme of the code is during night times it starts glowing with 20% intensity when an object approaches due to that object and vehicle light due to this light will glow 100% intensity. I wrote the code as
int led1=5;
int potpin1=0;
int val1=0;
int led2;
int potpin2=0;
int val2=0;
int ir1=A2;
int ir2=A3;
int ldr = A0;
void setup()
{
pinMode(led1,OUTPUT);
pinMode(led2,OUTPUT);
pinMode(ir1,INPUT);
pinMode(ir2,INPUT);
pinMode(ldr,INPUT);
Serial.begin(9600);
}
void loop()
{
int ldrValue=analogRead(ldr);
Serial.print("Sernsor =");
Serial.print(ldrValue);
if(ldrValue
mention led2 pin, you have not mentioned in the code
it is not working
What kind of issues are you facing?
PLZZ tell mee
Sir once please check mail sir
Sir u have used three wires to connect ,instead of those we can use jumper wires
Are you saying about IR sensor? My IR sensor have 3 pins, output, ground and Vcc. Do you want to say that you want to make common grounds and common Vcc? Then yes we can do that also.
After uploading the code in serial monitor it is showing sensor = 0
What should I do
Sir it's working successfully but after removing the object the light is in still on
@@kushalkumaruppada1462 you can change the threshold value in the code as per the LDR output