I wish the BlueGhozt controller could be updated to make the turn signal inputs fully customizable and not just limited to turn signal animations. What I mean is, for example my interior lighting. When you turn the headlights on at night, the parking light input is used to have my interior strips do a startup animation then stay on blue. I'd like to be able to do the same when a door is opened/dome light turned on, to have them animate to white, then animate back to blue when Door shut/dome light turned off. Even take a step further and do an animation to indicate when the Ignition is turned on/vehicle started. (Just the animation, but not staying on steady afterwards)
I am very impress this is all done on 1 strip of leds, I am currently working on my own dyi headlight project, that have 2 RGB halos rings, 1 RGB demon eye in the projector lens and 1 SRGBA turn signal / daytime running light per 1 headlamp housing. i bought some SRGBA LEDs from Misun Auto plus halo rings and demon eyes which came with the sp105e magic controller and i am now thinking this controller seam to be way better controller, if it can run all my leds. I might have to contact your company to see if its possible.
yeah that should be doable, our controller supports up to 350 LEDs on each of its 2 outputs, and you can chain any number of strips/halos together along this output. You can then configure how many LEDs are in each strip and then pick which ones are enabled for turn signals, brakes, parking lights, etc. extremely customizable!
@@ghoztlighting Thank you for the fast reply, i will email soon with a better mock up design on my plans to get your opinion if I am going in the right direction and if your controller will work for me, which i believe it will. thanks for your time.
*Can you hook up those 1 watt Power LEDs with blue ghozt? If yes how many? I see two JST connections. But are there those individual connections available? 28 channel type?* *think these neo pixel strips look bright in the dark only. But in daytime do they look too faint???*
I see 4 inputs for the module parking, break, turn, reverse. But my car has a rear fog lamp that is integrated in the tail lamp. So tail lamp has 5 bulbs parking, break, turn, reverse....and fog so how would one enable a fog lamp?
mmace3 screw in some wires to the turn signal terminals and tap each wire separately to a battery positive or 12v current to see if it does the turn signal inputs
What are you using to send power to the 4 inputs? (2 Turn signals, running lights, and brake lights) Trying to find a clean way to power headlights and test signals with a flip of a switch.
Can you run any adressable rgb led that's says it is ws2811 or is it specific to the neopixel. Just ordered the plus and I already have a bunch of 144 led strips.
Hey, it's been a while since someone last asked this question? But, I want too purchase the Neopixels for my car? Where would I go to purchase the one that are shown in this video?
If I where to have tail lights that a full matrix but each column and row aren't gonna have the same amount of LEDs would this still work with it? Thanks.
Where can I contact u regarding when turn my headlights on (low beam) the halos and eyebrows pulse when I turn off the headlights they stop also when I lets say I have 88 led in one headlight I reduce it to 76 and then turn my headlights on they don’t pulse
Can I run a rgbw ws2812b neopixle strip on this controller and get turn signal and pure white drl or do I have to run the adafruit neopixle digital rgbw to get these functions
I’m running into an issue where my BlueGhozt isn’t connecting to any of my iOS devices. Configuration: -12v power supply to 5V converter to BlueGhozt -BlueGhozt output to WS2812B led strip -3x iOS devices (iPhone XS Max, iPhone XS, iPad Pro 11 inch) all devices on up to date iOS All devices won’t connect to my BlueGhozt >> after power cycling the iOS devices, the issue persist
Ya this shit is pretty complex. I feel like the people who built light are specialty. I could rip them out, but custom lights and programing is way above my paygrade. Lol id take a few years to learn all this stuff for a decent setup.
In need of help. If we had hyperflash before installing do we need to install resistors to make this work better? Also, i connected the left turn signal, had power and both strips turned on
Yeah you will still need load resistors like normal. We couldn't include them on the board because they produce so much heat. Regarding which strips turn on for what function, you'll need to configure that in the app first for it to work how you want.
@@ghoztlighting update. I added my resistors, i connect to the app for left turn signal, on app it shows the right turn signal is activated. Then i look at my headlights and both aides are on? Any idea or help. Tjanks a lpt
What’s up man I’m thinking of buying NEOPRISM-X strips and this Bluetooth controller, is there any wiring I have to tap into my turn signals for the strips to do switchback function so everytime I hit my turn signal they flash orange and then once it’s off go back to the color it was on ?
Is it possible for the ghozt controller to interface with music through the app I use spotify alot for music from my phone where I have the ghozt app so that reacts to music either through the mic of my phone or otherwise?
@@ghoztlighting is there any plan to update portal have that feature in the future or something maybe you're working on now or does it just update the app definitely very interested in and I think I'm getting it no matter what cuz I like the customization that you can do with the addressable LEDs so I can't wait until I get my glucose controller and set it up in my Yukon
@@The_Bandit_750 a stock led signal wouldnt have rgb it would just be amber. That's why led tube lights turn off when someone turns on their signals cos there's no power to them.
@@mertcapkin7263 that's known as the data line. Each channel can control up to 350 LEDs lengthwise, if you use a splitter you can have more but they will do identical things as each other since it is the same data signal.
Appreciate the video. Just finished setting mine up. Just waiting for my wire taps now to hook everything up.
I wish the BlueGhozt controller could be updated to make the turn signal inputs fully customizable and not just limited to turn signal animations.
What I mean is, for example my interior lighting.
When you turn the headlights on at night, the parking light input is used to have my interior strips do a startup animation then stay on blue.
I'd like to be able to do the same when a door is opened/dome light turned on, to have them animate to white, then animate back to blue when Door shut/dome light turned off.
Even take a step further and do an animation to indicate when the Ignition is turned on/vehicle started. (Just the animation, but not staying on steady afterwards)
You can do this with the BlueGhozt plus with the additional 12v power switched
This video makes so much more sense now that I’ve got mine hooked up on me test bench...
Do we need to program the blue ghost too if we want to make our own animations? If yes what device is used to programming?
13:30 WOW!!!....Which preset effect is THAT?....Please? Wave at a slow speed?
I am very impress this is all done on 1 strip of leds, I am currently working on my own dyi headlight project, that have 2 RGB halos rings, 1 RGB demon eye in the projector lens and 1 SRGBA turn signal / daytime running light per 1 headlamp housing. i bought some SRGBA LEDs from Misun Auto plus halo rings and demon eyes which came with the sp105e magic controller and i am now thinking this controller seam to be way better controller, if it can run all my leds. I might have to contact your company to see if its possible.
yeah that should be doable, our controller supports up to 350 LEDs on each of its 2 outputs, and you can chain any number of strips/halos together along this output. You can then configure how many LEDs are in each strip and then pick which ones are enabled for turn signals, brakes, parking lights, etc. extremely customizable!
@@ghoztlighting Thank you for the fast reply, i will email soon with a better mock up design on my plans to get your opinion if I am going in the right direction and if your controller will work for me, which i believe it will. thanks for your time.
🤰
*Can you hook up those 1 watt Power LEDs with blue ghozt? If yes how many? I see two JST connections. But are there those individual connections available? 28 channel type?*
*think these neo pixel strips look bright in the dark only. But in daytime do they look too faint???*
Subbed! Thanks for this man!!
*Also can you tell what is the ampeage on the blughost module output. 12v i know... but what is the max amprage output for those jst connectors?*
I see 4 inputs for the module parking, break, turn, reverse. But my car has a rear fog lamp that is integrated in the tail lamp. So tail lamp has 5 bulbs parking, break, turn, reverse....and fog so how would one enable a fog lamp?
Can this do start up animations like the original ghozt
How do I save my led strips settings so after I disconnect from power 12v my config will stay on the controller ?
😍 I need to step it up
I have the BlueGhozt controller but don't know how to test the turn signals. What is the turn signal generator that you mentioned?
mmace3 screw in some wires to the turn signal terminals and tap each wire separately to a battery positive or 12v current to see if it does the turn signal inputs
What are you using to send power to the 4 inputs? (2 Turn signals, running lights, and brake lights) Trying to find a clean way to power headlights and test signals with a flip of a switch.
I want to make purchase of this BlueGhozt but hw do I connect the turn signal to my car what driver do I need to do that
John K I have the same question have you found out the answer?
Which pixels are these in the video, apologies if asked that before
Can you run any adressable rgb led that's says it is ws2811 or is it specific to the neopixel. Just ordered the plus and I already have a bunch of 144 led strips.
Neopixel is just Adafruit's brand name, you can use any addressable LEDs
So can you use the module for the hole car. Or just front and back
Hey, it's been a while since someone last asked this question?
But, I want too purchase the Neopixels for my car?
Where would I go to purchase the one that are shown in this video?
If I where to have tail lights that a full matrix but each column and row aren't gonna have the same amount of LEDs would this still work with it? Thanks.
Where can I contact u regarding when turn my headlights on (low beam) the halos and eyebrows pulse when I turn off the headlights they stop also when I lets say I have 88 led in one headlight I reduce it to 76 and then turn my headlights on they don’t pulse
Can I run a rgbw ws2812b neopixle strip on this controller and get turn signal and pure white drl or do I have to run the adafruit neopixle digital rgbw to get these functions
Are those 144/m or 60/m led strip?
Those are 144/m
I’m running into an issue where my BlueGhozt isn’t connecting to any of my iOS devices.
Configuration:
-12v power supply to 5V converter to BlueGhozt
-BlueGhozt output to WS2812B led strip
-3x iOS devices (iPhone XS Max, iPhone XS, iPad Pro 11 inch) all devices on up to date iOS
All devices won’t connect to my BlueGhozt >> after power cycling the iOS devices, the issue persist
Please contact us at support@ghoztlighting.com or on Facebook for troubleshooting assistance!
Did you ever resolve this issue?
Ya this shit is pretty complex. I feel like the people who built light are specialty. I could rip them out, but custom lights and programing is way above my paygrade. Lol id take a few years to learn all this stuff for a decent setup.
In need of help. If we had hyperflash before installing do we need to install resistors to make this work better? Also, i connected the left turn signal, had power and both strips turned on
Yeah you will still need load resistors like normal. We couldn't include them on the board because they produce so much heat.
Regarding which strips turn on for what function, you'll need to configure that in the app first for it to work how you want.
@@ghoztlighting update. I added my resistors, i connect to the app for left turn signal, on app it shows the right turn signal is activated. Then i look at my headlights and both aides are on? Any idea or help. Tjanks a lpt
What’s up man I’m thinking of buying NEOPRISM-X strips and this Bluetooth controller, is there any wiring I have to tap into my turn signals for the strips to do switchback function so everytime I hit my turn signal they flash orange and then once it’s off go back to the color it was on ?
Yeah, you just tap into the turn signal wires.
When using the 5v halo/strips. Do i only need one 12v-5v converter for all halo/strips? Say i have 6 units, i still only need the one converter?
it depends on how many amps you are running. we have both 10 and 20 amp converters, but yes you only use one
@@danielevans5431 Ah, get it. Thanks :)
Is it possible for the ghozt controller to interface with music through the app I use spotify alot for music from my phone where I have the ghozt app so that reacts to music either through the mic of my phone or otherwise?
No, there is no music sync feature yet.
@@ghoztlighting is there any plan to update portal have that feature in the future or something maybe you're working on now or does it just update the app definitely very interested in and I think I'm getting it no matter what cuz I like the customization that you can do with the addressable LEDs so I can't wait until I get my glucose controller and set it up in my Yukon
@@MegaWolfman76 its possible it will be added to a future unit, we have a big update coming soon that will add more show modes and options as well
So I run one 12v wire to my led turn signal and I get cool stuff?
If your taillight has Neopixel-style LEDs already installed, then definitely! If not then you would need a custom build
Ghozt Lighting shit man😒
@@The_Bandit_750 a stock led signal wouldnt have rgb it would just be amber. That's why led tube lights turn off when someone turns on their signals cos there's no power to them.
Ok so if you have 12v underglow will you need the 12v to 5v to run it
how many individual strips can you control with this unit?
If you use a splitter, you can control as many as you have wired up power for. If you connect them end to end, each channel controls 350 pixels.
@@danielevans5431 yeah but they will be on the same signal wire, right?
not sure what you mean by signal wire
@@danielevans5431 the LED strips have positive negative and signal wires
@@mertcapkin7263 that's known as the data line. Each channel can control up to 350 LEDs lengthwise, if you use a splitter you can have more but they will do identical things as each other since it is the same data signal.
How can I control 4 strips from blueghozt?
You can control up to 350 LEDs per output (2) for 700 total, on any number of strips and halos. You connect them end to end.
Lighting Trendz sells a version of the Blueghozt that they'll customize with up to 8 outputs.
@@imdbtruth they use a splitter, it's the same number of outputs just some mirror each other.
@@ghoztlighting Are you saying that their version has the same two JST style LED connectors coming out of the unit, but then they use a JST splitter?
@@imdbtruth yeah it's the same Blueghozt unit nothing technically different, just wired up differently.
Have you used the neopixel/addressable LEDs as brake lights? I'd like to convert my tail lights to all neopixel but I'm concerned about brightness
Guy did it in Instagram. I wouldn't try it. They were not bright at all during the day.
That is awesome but you sound so monotone and scripted. More enthusiasm
Oh shut the fuck up