Had the same issue with spark. What worked for me after talking to DJI support: when you reset spark's wifi settings with 3 beeps (holding power for ~9 seconds) turn it off immediately once you start seeing spark LEDs blinking green! Don't wait and just turn it off once it starts blinking green. Then, when you turn it on again, give it a few seconds to warm up and start, and hold power for 3 seconds. After that controller pairs to drone no prob in a standard way (3 buttons pressed at the same time). works like a charm.
Dji UA-cam channel , multiple forums ,Dji Manual , advice from fellow flyers all useless until this guy and his video description showed up!! Thanks a lot man !
Wow... I have tried everything and your solution has been the only one that has worked! I commend you for figuring this out and posting the solution. I was almost ready to package it all up and send it back to DJI for repair. You are a lifesaver!
It worked for me my issue was I am using iPhone didn't able to connect after forgetting network Thing i did is turnoff the spark and turn-on the RC and holded it for first beep then enter the password and it is connected Thanks for the help mate appreciate it
спасибо за решение проблемы! неделю мучался и не мог подключить. уже хотел с помощью софта сбрасывать прошивки до заводских. с этим "решением проблемы" все получилось! так же после включения пульта и квдрика они автоматом конектятся друг к другу без всяких нажатий клавиш
I had that problem when I try to use spark in Ukraine,I couldn't sleep 2 days because of that problem :)...it's solved with your solution..thank you very much..thanks a lot
Steps 5,6,7 are not required. The main goal is to reset both devices and turn them off. Then turn on drone ONLY, switch it to expose WiFi mode(two beeps), switch it to link mode(one beep) and only than turn on controller and switch controller to linking mode. But, great thanks anyway - it was very helpful!
Merci pour tout, je galère depuis plus de 10 jours avec le même problème, j'ai suivie la procédure de TestAndRest et ça a marché, j'ai juste constaté que cela marche que si il y a une carte mémoire dans le spark, et n'hésitez pas à refaire la procedure si cela ne marche pas le premier coup , mille merci encore :)
Do you know how to avoid the reset message at the beginning? The one that says to reset the wlan because of the different country, that basically screws your connection if you press OK (and there's not another button to press)
Follow the below steps from 1 of the member, it solved my problem which was same as your... Read it first from 1-9. You should follow exact steps step-by-step to succeed. 1. Power up your Sparky. 2. Press Power button 9 seconds (3 Beeps) 3. Restart your Spark (power off and on again) 4. Press Power button 6 seconds (2 beeps) 5. Restart your Spark. 6. Press Power button 3 seconds (1 beep) 7. Now Power up your remote (just now). 8. Wait till Red light will stop blinking and just remain red. 9. Now press 3 keys on your remote to start the connection.
Travelkolik HU my problem: fly more combo. It was already paired. But no wifi. So I press button on spark for six seconds. Then lights went solid red. I cannot fix the problem now...someone help me please...I’m lost
Yesterday was trying all day to fix the pairing problem. Brought my combo from Singapore to Europe. Could not connect the remote with aircraft by all your methods. Problem is that WiFi frequency setting change due to location, frequencies of rc and ac were not the same when I changed location radically. Install fake gps (e.g. floater) fake your location to be e.g usa, connect to drone, - see that u have different frequencies. Pair drone with remote. After binding the floater might be not necessary. No playing with resets might be needed
I did it with your help!!!! thenx for messaging and good ideas!!! [b]So solution is in this steps[/b] 1. Turn off Controller and Spark 2. Turn on Controller 3. Reset Controller (long press for 9 second Power Button) 4. Turn Off Controller 5. Turn On Spark 6. Long press on Battery button for two beeps (6 second) 7. Turn off Spark 8. Turn On Spark 9. Long press on Battery button for three beeps (9 second) 10. Turn Off Spark 11. Turn On Spark 12. Once Again press on Battery button for two beeps (6 second) 11. Then (without turn off) press on Buttery button for 1 beep (3 ceconf) 12. Turn on controller 13. Press tre battons Red Pause + Fn + Right Custom button till you hear short beeps and green sparking light 14. They connected in my case!!! Once again - thenx every one for help!
you need to switch wifi to 2.4ghz by holding power AC botton in 6 sec or wait until you heard two beeps. then try to link again. by holding pause+fn+fn2 on RC. And then on AC for 3 sec or one beep. no need to reset setting holding for 9 sec or three beeps
I need help with this I tried all these steps but my spark will not beep after 3 seconds. It’s brand new (fly more) the controller connects to phone perfectly
My spark's RC is now in 5.8 GHz.i tried a lot to change to 2.4 GHz.but it is still in 5.8.i discussed with dji support and they told me to do so many things.still it is in 5.8.can u help me to solve the issue.in our region only 2.4 GHz
I had same issue...controller would not connect to aircraft and was beeping like crazy. I have tried everything but nothing helped. But I saw some warnings on my phone (in app) and that was the key. I had to calibrate aircraft and then calibrate sticks. Follow instructions! After calibrating and restarting aircraft and controller everything was working fine. Controller connected to the aircraft in few seconds and now everything is working perfectly. Hope that hepls you guys as well
Hi,try this procedure.it always works for me: 1. Push the 9sec reset on both aircraft and remote control. 2. Connect aircraft with phone only,go out,wait to get GPS locked,then push auto take off.wait a fee second,then land the aircraft. 3. Go inside,link the remote with aircraft again. Always works for me when aircraft and remote cannot link.
I had this problem when i first recieved my remote controller. i just repeated the linking process over and over until it eventually connected. took over a hundred tries. now i got the regions message again and accidentally pressed ok. it destroyed the link and now i cant pair the aircraft and remote again
been updating and downgrading the firmware. it does absolutely nothing. just a time waster that the dji support wants you to do to get you off the line.
All you have to do is the 2 buttons on the front of the controller and the right rear button on top the back one hold all 3 of them down at the same time and it will bind to the drone
Hi new friend WE are from Argenntina and I have this problem on my Spark RC this is whitout pass to green light , without wifi emition and Spark whitout conection and fly Sadly I have not solution at the moment , But if this RC would like to know if a hard reset , is the solution , I think the problem by RC firmaware not completed , Thanks Oscar
Гдето 100метров улетаешь и картинка лагает на телефоне!!! Тормозит сильно. Контроллер с дроном ок а вот картинка на тнлефон лагает. Есть какое то решение этрй проблемы? Спасибо
After connecting to your phone you always have to hold the drone power button until you get 2 beeps after connecting to your phone to get it to pair back with the remote, I think that was the major step that caused the issue.
Having issues myself, however I'm not getting mine to even start the linking process, I just get 1 quieter beep and the led continues to flash red. Anybody have this happen!? Any help is greatly appreciated!!
turn drone on then RC- Press and hold for 3 secs the drone - release when it beeps & the red lights are blinking-Then on RC press function, , pause and the custom button at the right back together at the same time - The RC light should go green you are now connected
uo pude hacerlo existosamente un par de veces con este metodo, pero ahora 24.06.2018, vuelve a ocurrir y esta forma de arreglar el problema ya no funciona, favor quien tenga la solucion que la publique, saludos
This guys mthod in the thread worked first try. ( Travelkolik HU) this guy is a G 1 month ago Follow the below steps from 1 of the member, it solved my problem which was same as your... Read it first from 1-9. You should follow exact steps step-by-step to succeed. 1. Power up your Sparky. 2. Press Power button 9 seconds (3 Beeps) 3. Restart your Spark (power off and on again) 4. Press Power button 6 seconds (2 beeps) 5. Restart your Spark. 6. Press Power button 3 seconds (1 beep) 7. Now Power up your remote (just now). 8. Wait till Red light will stop blinking and just remain red. 9. Now press 3 keys on your remote to start the connection.
question is how to cmplain about it when it disconnects during flight? i read people losing their drones due to remote issues, no mods all stock, yet with more then 50% battery life the remote alerts a autopilot fly away, does not RETURN TO HOME, disrupts the flight logs showing the aircraft i in perfect condition, perfect day and less then 200m away yet DJI says they can only offer these victims 30% off on another purchased giving them little time to decide. If you buy a car and it drives away due to break issues, motor issues etc and no wrong doing was done on the drivers part before a crash or fall of a cliff is it not the manufactures fault when they dont know what caused it? How can they sell a drone, have all the flight data and not know it was caused by the remote itself, After reading several threads i also realized DJI is tealing with Apple who cyber bullies critics about bugs or issues which 9 out of ten times where all RECALLS., they mock, insulted , gaslighted and even blamed the victims of fly away drones to close the threads, Imagine the threads dating back 5 years with comments until date of more and more pilot horror stories been told its an old issue DJI fixed....you did not get this with the GopRo Karma.. Class Action is the only way to deal with companies that abuse their customers and put the public at risk (which is the reason i personally think DDJI would never admit their remotes are faulty at times)
You are doing the binding wrong, read the remote control manual, it states very clear how to bind remote to Spark Switch the remote on. Now press the pause button (red one) and the FN button and right back button at the same time, and hold till remote starts beeping. Now switch on the Spark and let it bootup now press and hold the battery switch for 9 seconds until you hear 3 beeps in total and the binding with the remote will start. When the light on the remote goes green binding is succes
This video showed me how to pair it. I successfully was able to get the controller to pair and get a green light, but the controller still does nothing. Slowly getting closer! See how this guy says to pair controller with drone: ua-cam.com/video/1DOCrKCLPzo/v-deo.html
Had the same issue with spark. What worked for me after talking to DJI support: when you reset spark's wifi settings with 3 beeps (holding power for ~9 seconds) turn it off immediately once you start seeing spark LEDs blinking green! Don't wait and just turn it off once it starts blinking green. Then, when you turn it on again, give it a few seconds to warm up and start, and hold power for 3 seconds. After that controller pairs to drone no prob in a standard way (3 buttons pressed at the same time). works like a charm.
this actually worked for me
too bad i had already bought an extra remote controller
THANKS A LOT. It works your Method for me. THANKS THANKS THANKS!
actually worked on me.. thank you
it works perfectly for me. thanks
I love you mannnnnn
Dji UA-cam channel , multiple forums ,Dji Manual , advice from fellow flyers all useless until this guy and his video description showed up!! Thanks a lot man !
The same situations I had! :))
Wow... I have tried everything and your solution has been the only one that has worked! I commend you for figuring this out and posting the solution. I was almost ready to package it all up and send it back to DJI for repair. You are a lifesaver!
Two days of torment. Thank you!
You are genious. I've been trying for three days without a luck untill I found your solution.
You my friend are a genius . Thank you ...I can stop banging my head against the wall start being nice to family and fly my spark again.
It worked for me my issue was
I am using iPhone didn't able to connect after forgetting network
Thing i did is turnoff the spark and turn-on the RC and holded it for first beep then enter the password and it is connected
Thanks for the help mate appreciate it
Thank you SO MUCH for this.
I struggled for 1.5 hours then tried what u said in the description.
Thank you so much! Been trying for the whole day to connect my controller without any luck. Your solution did the trick!!
Wow... with a brand new drone and controller I had to go through all this. However... IT WORKED. Thanks a lot for sharing.
спасибо за решение проблемы! неделю мучался и не мог подключить. уже хотел с помощью софта сбрасывать прошивки до заводских. с этим "решением проблемы" все получилось! так же после включения пульта и квдрика они автоматом конектятся друг к другу без всяких нажатий клавиш
THIS PROCEDURE IS WORKING 100% THANKS MAN...... TRY IT!!!!! THANK YOU REALLY
I had that problem when I try to use spark in Ukraine,I couldn't sleep 2 days because of that problem :)...it's solved with your solution..thank you very much..thanks a lot
Followed the instructions in the description and it worked! Thanks for uploading this!
Steps 5,6,7 are not required. The main goal is to reset both devices and turn them off. Then turn on drone ONLY, switch it to expose WiFi mode(two beeps), switch it to link mode(one beep) and only than turn on controller and switch controller to linking mode. But, great thanks anyway - it was very helpful!
thank you
I can't believe this worked!
Дякую за фікс, сьогодні купу часу вбив на суппорт. Навіть дзвонили з Китаю. То було жахливо. Але ось тут був дуже прости та крутий фікс! Дякую!!!
Хай літає!
I followed your solution and it worked for me. Thank you. Liked and subscribed.
Thank you
Thank you so much my brother
My controller was the same problem, its solved! Thank you very much bud!!!!
GREAT GREAT.AWESOME.ITS VERY HELPFUL FOR ME.THANKS A LOT.
it worked, thanks dude been struggling with this for a while now
WORKED 4 ME!!!!!!! Thanks man! U r a life saver!
Loads of help worked for me 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍😁
Thank u so much the only solution worked for me..
Merci pour tout, je galère depuis plus de 10 jours avec le même problème, j'ai suivie la procédure de TestAndRest et ça a marché, j'ai juste constaté que cela marche que si il y a une carte mémoire dans le spark, et n'hésitez pas à refaire la procedure si cela ne marche pas le premier coup , mille merci encore :)
Content d'avoir aidé)
Unbelieveble thank you so much, already liked your video.
Thank you so much! I forgot my drone password and you allowed me to reset it! ☺️
I LOVE YOU!!! Daaaaamn I was going crazy, thank you!!!
Do you know how to avoid the reset message at the beginning? The one that says to reset the wlan because of the different country, that basically screws your connection if you press OK (and there's not another button to press)
Follow the below steps from 1 of the member, it solved my problem which was same as your...
Read it first from 1-9. You should follow exact steps step-by-step to succeed.
1. Power up your Sparky.
2. Press Power button 9 seconds (3 Beeps)
3. Restart your Spark (power off and on again)
4. Press Power button 6 seconds (2 beeps)
5. Restart your Spark.
6. Press Power button 3 seconds (1 beep)
7. Now Power up your remote (just now).
8. Wait till Red light will stop blinking and just remain red.
9. Now press 3 keys on your remote to start the connection.
Thank you so much. This is help to me.
Your the god
Travelkolik HU my problem: fly more combo. It was already paired. But no wifi. So I press button on spark for six seconds. Then lights went solid red. I cannot fix the problem now...someone help me please...I’m lost
Doesn't do a thing to my sparky remote
Yesterday was trying all day to fix the pairing problem. Brought my combo from Singapore to Europe. Could not connect the remote with aircraft by all your methods. Problem is that WiFi frequency setting change due to location, frequencies of rc and ac were not the same when I changed location radically. Install fake gps (e.g. floater) fake your location to be e.g usa, connect to drone, - see that u have different frequencies. Pair drone with remote. After binding the floater might be not necessary. No playing with resets might be needed
Having the same problem... how did you fix it
im not fix it yet((((
I did it with your help!!!! thenx for messaging and good ideas!!!
[b]So solution is in this steps[/b]
1. Turn off Controller and Spark
2. Turn on Controller
3. Reset Controller (long press for 9 second Power Button)
4. Turn Off Controller
5. Turn On Spark
6. Long press on Battery button for two beeps (6 second)
7. Turn off Spark
8. Turn On Spark
9. Long press on Battery button for three beeps (9 second)
10. Turn Off Spark
11. Turn On Spark
12. Once Again press on Battery button for two beeps (6 second)
11. Then (without turn off) press on Buttery button for 1 beep (3 ceconf)
12. Turn on controller
13. Press tre battons Red Pause + Fn + Right Custom button till you hear short beeps and green sparking light
14. They connected in my case!!!
Once again - thenx every one for help!
good job! thanks!
WORKED!!!!!
When I hold the button all it does is just continue to beep
DCNationVideos1 this is what mine keeps doing too. Did you find a solution?
It worked for me. Thanks very much! ;)
wow! nice... worked like a charm. Thank brother
Worked for me! Thank you so much!
дякую друже!!! допомогло) всього найкращого тобі))))
Thanks for sharing
Yes...thanks man..it worked just as you wrote ;)
Thanks for this video! Really helped me a lot!
Thanks, it did help me!
Thanks for the solution! It works!
Hi bro my dji spark won’t beep or reset wifi I tried to connected with pc windows 10 but not recognize it at all !??
Please help
Saved me!!! Thank you, Thank you, THANK YOU!!!
I have my phone link to my spark remote controller, but I put the wrong password by mistake how can I fix it
you need to switch wifi to 2.4ghz by holding power AC botton in 6 sec or wait until you heard two beeps. then try to link again. by holding pause+fn+fn2 on RC. And then on AC for 3 sec or one beep. no need to reset setting holding for 9 sec or three beeps
oh! this is 2 months old vid. hahahaha
thanks man!!! It did help me!
Zkungfui Your my Hero! Thank you!!!!!!!
THAKS DEAR FRIEND YOU ARE MY GOD MUST CANNACTED YOUR ADUVACE VERY HELP FULL
Thank you dude it works for me.
I need help with this I tried all these steps but my spark will not beep after 3 seconds. It’s brand new (fly more) the controller connects to phone perfectly
Thanx!
My spark's RC is now in 5.8 GHz.i tried a lot to change to 2.4 GHz.but it is still in 5.8.i discussed with dji support and they told me to do so many things.still it is in 5.8.can u help me to solve the issue.in our region only 2.4 GHz
Thanks Mate helped so much
Thanks!!!!!
Thank a lot ❤️😍
Thanks.... Very helpful
Yessss it worked for me thank you
well i tried the instructions to the letter above and yes the green light came on but it kept beeping and wouldn't stop so didnt work properly :(
Perfect! Thanks!
It works! Thanks!
Try opening the antennas. Folded they cancel easy other
remember to thank you
I had same issue...controller would not connect to aircraft and was beeping like crazy. I have tried everything but nothing helped. But I saw some warnings on my phone (in app) and that was the key. I had to calibrate aircraft and then calibrate sticks. Follow instructions! After calibrating and restarting aircraft and controller everything was working fine. Controller connected to the aircraft in few seconds and now everything is working perfectly. Hope that hepls you guys as well
Thank you!
Hi,try this procedure.it always works for me:
1. Push the 9sec reset on both aircraft and remote control.
2. Connect aircraft with phone only,go out,wait to get GPS locked,then push auto take off.wait a fee second,then land the aircraft.
3. Go inside,link the remote with aircraft again.
Always works for me when aircraft and remote cannot link.
Thanks man it works
I had this problem when i first recieved my remote controller. i just repeated the linking process over and over until it eventually connected. took over a hundred tries. now i got the regions message again and accidentally pressed ok. it destroyed the link and now i cant pair the aircraft and remote again
been updating and downgrading the firmware. it does absolutely nothing. just a time waster that the dji support wants you to do to get you off the line.
All you have to do is the 2 buttons on the front of the controller and the right rear button on top the back one hold all 3 of them down at the same time and it will bind to the drone
Hi new friend WE are from Argenntina and I have this problem on my Spark RC this is whitout pass to green light , without wifi emition and Spark whitout conection and fly Sadly I have not solution at the moment , But if this RC would like to know if a hard reset , is the solution , I think the problem by RC firmaware not completed , Thanks Oscar
O meu controle não mando o sinal wi-fi oque pode ser amigo sou do Brasil se puder me ajudar
thanks its works for me
it worked!!! thx
Гдето 100метров улетаешь и картинка лагает на телефоне!!! Тормозит сильно. Контроллер с дроном ок а вот картинка на тнлефон лагает. Есть какое то решение этрй проблемы? Спасибо
переключайтесь в режим FCC
ua-cam.com/video/Is7_btFs1G8/v-deo.html
Valerii Iavtushenko и что это поможет? Так то я живу в Тайланде….
Так - в Україні допомогло
Down grade the spark then connect it to controller. After that u upgrade the spark
amty lolo: I can not down grade. only at the highest fw.
Thichu Giang there is a way to downgrade through the dji go app. Search for it.
i down fw can not linking
Merci beaucoup, ca fonctionne pour moi :)
так а в чем решение-то? На какой минуте видео оно !!!SOLVED!!!???
Read description to the video -all there
Valerii Iavtushenko а да сорри
Finalyyyy It worked!!!!!
When connecting turn off your modules phone data then back on after it connects, works for me.
After connecting to your phone you always have to hold the drone power button until you get 2 beeps after connecting to your phone to get it to pair back with the remote, I think that was the major step that caused the issue.
Having issues myself, however I'm not getting mine to even start the linking process, I just get 1 quieter beep and the led continues to flash red. Anybody have this happen!? Any help is greatly appreciated!!
same problem sometimes it works sometimes it doesnt
You are the best!!! Thank you sooo much
1098375384359 likes
Hi again :-)
turn drone on then RC- Press and hold for 3 secs the drone - release when it beeps & the red lights are blinking-Then on RC press function, , pause and the custom button at the right back together at the same time - The RC light should go green you are now connected
You have now fixed this bug
yes
uo pude hacerlo existosamente un par de veces con este metodo, pero ahora 24.06.2018, vuelve a ocurrir y esta forma de arreglar el problema ya no funciona, favor quien tenga la solucion que la publique, saludos
If it helps - little donation will be soooo goood
paypal.me/testandrest
Where in Ukraine are you, I live in Kiev. I just got my spark !!!
Congratulation - in centre of Ukraine, Poltava city
Hi everybody.
This is an issue. I called tech support. They told me to use otg cable. With otg works perfect
This guys mthod in the thread worked first try.
( Travelkolik HU) this guy is a G
1 month ago
Follow the below steps from 1 of the member, it solved my problem which was same as your...
Read it first from 1-9. You should follow exact steps step-by-step to succeed.
1. Power up your Sparky.
2. Press Power button 9 seconds (3 Beeps)
3. Restart your Spark (power off and on again)
4. Press Power button 6 seconds (2 beeps)
5. Restart your Spark.
6. Press Power button 3 seconds (1 beep)
7. Now Power up your remote (just now).
8. Wait till Red light will stop blinking and just remain red.
9. Now press 3 keys on your remote to start the connection.
It sucks to pay $399.00 plus tax for a drone that is pure hell to get the controller connected. The spark should sell for $3.99 not $399.00.
question is how to cmplain about it when it disconnects during flight?
i read people losing their drones due to remote issues, no mods all stock, yet with more then 50% battery life the remote alerts a autopilot fly away, does not RETURN TO HOME, disrupts the flight logs showing the aircraft i in perfect condition, perfect day and less then 200m away yet DJI says they can only offer these victims 30% off on another purchased giving them little time to decide.
If you buy a car and it drives away due to break issues, motor issues etc and no wrong doing was done on the drivers part before a crash or fall of a cliff is it not the manufactures fault when they dont know what caused it?
How can they sell a drone, have all the flight data and not know it was caused by the remote itself,
After reading several threads i also realized DJI is tealing with Apple who cyber bullies critics about bugs or issues which 9 out of ten times where all RECALLS., they mock, insulted , gaslighted and even blamed the victims of fly away drones to close the threads,
Imagine the threads dating back 5 years with comments until date of more and more pilot horror stories been told its an old issue DJI fixed....you did not get this with the GopRo Karma..
Class Action is the only way to deal with companies that abuse their customers and put the public at risk (which is the reason i personally think DDJI would never admit their remotes are faulty at times)
cant hear you bro
Russell Bowen look at the description - everything there
Я ничего не понял. У меня таже проблема. Но ничего не вышло
& no with this one too :/
i managed to do it and didnt have to go throught all that
I have worst linking experience with Spark Combo & finally returned it. DJI selling rejected pieces, believe me.
You are doing the binding wrong, read the remote control manual, it states very clear how to bind remote to Spark Switch the remote on. Now press the pause button (red one) and the FN button and right back button at the same time, and hold till remote starts beeping. Now switch on the Spark and let it bootup now press and hold the battery switch for 9 seconds until you hear 3 beeps in total and the binding with the remote will start. When the light on the remote goes green binding is succes
Ruudy L my problem is the lights on the drone are solid red. I have the fly more combo...I messed up somewhere and can’t figure it out
Doesnt really work, RC LED keeps blinking red twice
This video showed me how to pair it. I successfully was able to get the controller to pair and get a green light, but the controller still does nothing. Slowly getting closer! See how this guy says to pair controller with drone: ua-cam.com/video/1DOCrKCLPzo/v-deo.html
Thanks for this video! It helped me a lot!