These Sennheiser Mics are so damn delicate! I have a e935 mic that I purchased on April 2021 and it mostly just stayed in my cupboard as I rotated my mics. Today I connected it and there's absolutely no sound. I have no idea if the inner coils are gone because it's not visible clearly. How the hell can "German" engineering be so obtuse about the fact that these delicate soldering points should be protected! it's the worst design I've ever seen. I'm never recommending another Sennheiser mic to anyone! This is crazy.
внутри батарея взорвалась и вытек электролит. На новые элементы питания микрофон не реагирует. Кое как поцарапал внутреннюю пружину и питание появилось но только 1 деление батареи. Как его полностью разобрать ?? и поможет ли ??
Привет, спасибо за просмотр. Если у меня будет возможность, я поделюсь ею с вами о том, как ее разобрать. Честно говоря, я впервые получаю эту модель и еще не имел опыта ее разборки.
Greetings from Argentina. I wanted to ask you if you can help me! I have the same microphone and now when I turn it on, on its display it has an indicator with the initials "AF" that measures how much signal is being transmitted while you speak or sing... Now when I turn it on, without speaking or singing directly, the "AF" signal that it marks on the display goes almost to the top, as if it were transmitting audio. and then when you actually start to sing or talk into the microphone, it picks up as usual but when it plays the audio it does it with a little bit of noise, like it's some kind of RF noise, bad signal. I already tried changing your capsule, changing cables, trying another receiving base, and obviously, the problem is the transmitter. Is it permanently damaged? Or what could be causing that? From already thank you very much for your time.
Hi, thank you for watching🙏 Try this steps. 1. Change the battery 2.Adjust the sensitivity to zero or negative -10 or -30 the lowest. 3.Re-tuning thru settings from receiver to get the exact frequency for your receiver if you sre using EM-XSW 2 receiver. If the above steps can't rectify the issue then possible it requires replacement of the transmitter board on the mic.
You probably receiving interference on your channel. Try other frequencies. Re-tune your receiver and handheld. If if didn't work try to increase your squelch level at the back of your receiver.
Hi, sorry as it was difficult to find this part. Try to search the part number online or send a message directly to Sennheiser support. www.sennheiser-hearing.com/en-US/support/
paano po malalaman + at negative ng voice coil, 3 po kasi ang pin nya, meron po kasi ako nabili na bmvoice coul, gusto ko ipalit yung voice coil sa ordinary na mic, pa help po, kung paano ang wiring, 2 lang po kasi ang contact ng ordinary na mic, yung sennheiser po 3
Hi, actually dalawa lng ang line ng Sennheiser na yan. Dalawa kasi ang coil. Voice inner coil at outer coil. Tatlo ang pin kasi naka serries yong connection ng inner coil at outer coil. Pag sinuri nyo po ang line ay dalawa lng yan papunta sa board.
@@ARTaudio440 saan ko po pwede ilagay saka dalawang gilid po? yung ma red po yung positive, tangal na po kasi yung wire nung nabili ko binaklas na pero buo yung coil naga naman kaya lang baka mamali ako ng lagay masira
Thank you! This video helped me to repair an E 840S Capsule.
Hi, you're welcome and thank you too for watching ☺️
Great video! What if the red wire has broken off, is there a way to fix it then?
Hi thank you for watching ☺️
I'm not so sure cauze if can possibly fix. I haven't experienced it yet.
These Sennheiser Mics are so damn delicate! I have a e935 mic that I purchased on April 2021 and it mostly just stayed in my cupboard as I rotated my mics. Today I connected it and there's absolutely no sound. I have no idea if the inner coils are gone because it's not visible clearly. How the hell can "German" engineering be so obtuse about the fact that these delicate soldering points should be protected!
it's the worst design I've ever seen. I'm never recommending another Sennheiser mic to anyone! This is crazy.
@@mostwanted_007 Hi, thank you for watching ☺️.
I would suggest checking the mic with the qualified technician.
Thanks from nepal
Hi, thank you for watching ☺️
внутри батарея взорвалась и вытек электролит. На новые элементы питания микрофон не реагирует. Кое как поцарапал внутреннюю пружину и питание появилось но только 1 деление батареи. Как его полностью разобрать ?? и поможет ли ??
Привет, спасибо за просмотр.
Если у меня будет возможность, я поделюсь ею с вами о том, как ее разобрать. Честно говоря, я впервые получаю эту модель и еще не имел опыта ее разборки.
Me interesaría ver como lo desmontas, necesito desmontar el mío 😅
Como se retirar essa cápsula tenho um que o fio se partiu muito pequeno
Greetings from Argentina. I wanted to ask you if you can help me!
I have the same microphone and now when I turn it on, on its display it has an indicator with the initials "AF" that measures how much signal is being transmitted while you speak or sing...
Now when I turn it on, without speaking or singing directly, the "AF" signal that it marks on the display goes almost to the top, as if it were transmitting audio.
and then when you actually start to sing or talk into the microphone, it picks up as usual but when it plays the audio it does it with a little bit of noise, like it's some kind of RF noise, bad signal. I already tried changing your capsule, changing cables, trying another receiving base, and obviously, the problem is the transmitter. Is it permanently damaged? Or what could be causing that? From already thank you very much for your time.
Hi, thank you for watching🙏 Try this steps.
1. Change the battery
2.Adjust the sensitivity to zero or negative -10 or -30 the lowest.
3.Re-tuning thru settings from receiver to get the exact frequency for your receiver if you sre using EM-XSW 2 receiver.
If the above steps can't rectify the issue then possible it requires replacement of the transmitter board on the mic.
You probably receiving interference on your channel. Try other frequencies. Re-tune your receiver and handheld. If if didn't work try to increase your squelch level at the back of your receiver.
I want to order a new coil can you help me please,,,, im from south africa cape town
Hi, sorry as it was difficult to find this part. Try to search the part number online or send a message directly to Sennheiser support. www.sennheiser-hearing.com/en-US/support/
paano po malalaman + at negative ng voice coil, 3 po kasi ang pin nya, meron po kasi ako nabili na bmvoice coul, gusto ko ipalit yung voice coil sa ordinary na mic, pa help po, kung paano ang wiring, 2 lang po kasi ang contact ng ordinary na mic, yung sennheiser po 3
Hi, actually dalawa lng ang line ng Sennheiser na yan. Dalawa kasi ang coil. Voice inner coil at outer coil. Tatlo ang pin kasi naka serries yong connection ng inner coil at outer coil. Pag sinuri nyo po ang line ay dalawa lng yan papunta sa board.
Sa positive at negative nmn ay ayos lng kahit magka baliktaran.
@@ARTaudio440 saan ko po pwede ilagay saka dalawang gilid po? yung ma red po yung positive, tangal na po kasi yung wire nung nabili ko binaklas na pero buo yung coil naga naman kaya lang baka mamali ako ng lagay masira
@@johndarwinroxas3346 Hi, pa send po ng picture sa Fb page facebook.com/ARTaudio440?mibextid=9R9pXO
I need new coil
Hi, I already replied. Thank you for watching 🙏