DIY Table Saw (How to Make a Saw | Table Saw or Bench Saw Machine)
Вставка
- Опубліковано 20 тра 2019
- In this video I am going to make a DIY Table saw, that you can make easily using several budget materials as shown in below. For this DIY mini Table saw machine I used a 775 motor with 24V supply to power up the Bench Saw machine.
Materials you need:
1) Small Lathe Accessories Kit (JTO/B10/B12/B16 Drill Chuck Set) - • Machifit No Power Spin...
2) 775 motor x1 - www.banggood.com/custlink/GG3...
3) 118XL Timing Belt - www.banggood.com/custlink/mmm...
4) XL10T Synchronous timing belt wheel 5mm - www.banggood.com/custlink/mmm...
5) 0-40V 10A PWM Motor speed controller - www.banggood.com/custlink/GvD...
6) 4’ Saw Blade - www.banggood.com/custlink/mGv...
7) Switch 10A - ebay.to/2WPT6j4
8) Power Connector - www.banggood.com/custlink/33m...
9) Ball Bearing Slide Rail - ebay.to/30Gg1zQ
10) Plywood & Screws
**Power Supply used to power up - • DIY Bench Power Supply...
Thank you.
Subscribe for more future creative project videos.
Subscribe “LahisTech”: bit.ly/2JHtlyc - Навчання та стиль
Very nice tablesaw and build. I swapped the weak 775 motor and speed control with a 400 watt ac motor ripped from a blender and it rocks.
Oh man I bet! Nice! That gave me an idea💡 🙂
Go with stitching machine motor
Magia, los pernos que sujetan el. Mandril se redujeron...
very good ! Other attention swivel by contraries
Good project... You can add/ draw some vertical + horizontal lines on the top which should help you in adjusting the cutting guide.
I loved you putting on the safety glasses at the end, nice job dude.
Is there a schematic for the electrical ie what's needed wattage, amperage etc
also ..the drawer slides not used. no practical application huh
Guantes, gafas de trabajo. Mandil. Cobertores para los oidos... niveles de seguridad.
La sierra es pequeña... pero la seguridad es necesaria...
Se nota que aún no se han volado algún dedo...
Интересная конструкция, Good!) Только линейку (2 шт. по краям) я бы сразу заложил, приклеив. И 2 листа фанеры идёт с усилием, рискуем порвать резину или двигатель. В целом - Класс, Лайк и Подписка!)))
Good idea
Nice project 👍👍
Thanks
excellent
Is it possible to extend on the side where is the drill chuck and make an mini late? So you can have 2in1 or better 3in1 if you add an table grinder
Mükemmel işçilik bravo👍
No habría unas arandelas mas grandes para sujetar el. Motor?
Show de bola
Thank you
Good job sir.. 👍👍👍
Project is very good,but
What is the technical
Requirements of the drill-
Chuck in the project more over will we use
Very cool project indeed. Two points: saw blade height adjustment is missing, and: the motor might be a little too weak. But: thumps *up* .
if we change the motor.....this is an awesome tool
Thumps up.....very funny!
Hermoso proyecto, gracias.
Hay fresas para taladrar en exagonal... Y colocar las tuercas...
සුපිරි
Filé só uma idéia põe as medidas na mesa aí não precisa medir mais só gabarita ok parabéns
Good! Определенно лайк. С удовольствием смотрю Ваши самоделки. Многое имеет интересные идеи.
Can it cut 2 inches thick pine tree board? (Soft wood) not hard wood. Please advise
Good table saw
Very good project 👍
Thank you
No entiendo hasta ahora... Para qué el mandril externo... Esperemos que sea para algo no extraño...
Hermosa improvisación... Y ahora... Qué más hago... ?
Qual o nome das peças para que possamos fazer ok obrigado
What would be the size of the top board used in this.
Aunque haya separación... Si no esta bien aislada... El polvo de la madera... es polvo... de la madera... Pero bueno... A la larga solo se va a dañar el motor... Pequeñeces...
But it's good product
nice video, please give some explanations while doing
The power supply was this 12v or higher? I am going to have a go at this,clear instructions thankyou 👌
You can use upto 24v dc with this motor. You are welcome.
@@LahisTechLT yeah I get that I have installed it all speed control dont work like that though,it does not run motor when it's less than half way,turn it on full and it runs weird I have used the same as you got there,i brought another to see if it was faulty but same thing.
@@stephencowley6226 may an issue with your motor i guess, or loose the belt little bit. This motor speed controller handles upto 10A 40V DC.
@@LahisTechLT yeah I give that a try thankyou for your help 👌
Excellent idea . thumbs up. However the durability ofthe motor is questionable. I would use a drill motor as its torque is higher.
775 motor is kind of a drill motor. Thank you
@@LahisTechLT
You are welcome. Yes it is indeed kind of a drill motor but in a drill it there is gears system that enhances the torque. In your case you used a belt , and this has some drwbacks (heat and negative effect on the motor torque . Additionally, the stronger drills use multiple-coil electromagnetic stator instead of a permanent magnet.
Once more, thanks a million for the idea.
What is the use of chuck
Bonsoir.
Bon travail
svp ou en peut acheté ces articles
Merci
Make a safety arrangement its very important
Indicador en rojo... Preferible...
Just want to know why need to use the belt and not direct turn from motor ?
Is it more turning power output ?
It is not just the power. Attaching a saw blade directly into motor shaft is not correct and good for the motor. (I mean it provides overload and jam protection) furthermore, it reduce the vibration of your table saw.
I see, learn something new for me today :D
Why use the Machifit Small Lathe Accessories Set? Why not just direct drive the saw blade off the motor?
I am want to no what material is used
Buying those tool could have cost more than a the cheapest tile circular saw.
What's a adapter voltage use please reply me
you can supply upto 24v 5A, this is the speed at 18v 5A
Kitne rpm ki moter he
I buy it how much.
Can I get 1 of those
Parece q o disco está girando para o lado contrário, talvez por isso deu trabalho pra cortar as madeiras de maior espessura
I need some help please. I bought 12V 795 Motor and power suply is 12v 10A, and the motor does not have the power to cut a 2cm thick wood. What is the problem? please help me, thank you
Use a larger power supply such as 18v or 24v. Most likely the 798 motor is still capable of that much pawer.
How can I buy this, and it's price,
How thick can it cut? Or how tall is blade above table? Please kin’s Sir.!
Bhai this is 775 dc motor this motors is very powerful it can also cut matel sheet but using matel cutter blade
Sensacional bom todo 2 em 1 kkk
If I want to buy, where I can buy this product.
I'm sorry not for sell
09
Very nice mate, just watch your damn fingers. ;)
Will you please tell me the top board dimensions. This is the second time I am asking you. Will you take care to respond?
1st
GUIDANCE PLEASE?
eBay listing shows sold out for motor. I found another seller / same motor for $4.00 more. Different seller.
Can you provide seller contact info? Save me 1/3 cost on motor. Also I will use power cord you used in different video, but I am afraid RPM / POWER of motor will decrease. Thank you. Alton
i want to buy it.. can it shipping at bangladesh??
Gg
No demostraron para que el mandril externo... Será solo para tirar lámpara?
O para que te moleste o dificulte la vida...?
Como idea... De 0 a 10 un 2...
Seguridad... 0
Video 3/10
Musica de fondo 0
En pocas palabras... le falta quaker...
0
wrong to install accessory kit without adjusting angle of circular saw
Ppo
9000oo999
you have 10 finger.... still