Redcat Ascent Best Mods & Easy Way to Remove Stock Tires
Вставка
- Опубліковано 29 жов 2023
- Redcat Ascent mods! How to remove stock tires and the mods I made.
Pick up the Redcat Ascent here (amain)
bit.ly/3RZTxqq
Redcat Ascent found here (amazon)
amzn.to/3SgttaT
Losi mini T springs found here (amain)
alnk.to/3yaZtjc
Losi mini t springs (amazon)
amzn.to/40gkDfa
Hobbywing Fusion SE motor/esc combo found here
bit.ly/3rVc7FP
ShiftRC Servo I’m running found here
Treal brass diff cover I used found here
amzn.to/45WuvMa
Brass Portal covers I’m gonna use found here
amzn.to/3FGoaKh
Capra links I’m running on lower rear found here
www.ebay.com/itm/123966930526...
CA Remover I used to remove tires
amzn.to/3QFbYjk
To contact me about reviews or questions email me at 2fastmattracing@gmail.com
I finally have Merch!!
Be sure to check the sizing chart and maybe size up on those Hoodies.
Check it out at the website below!!
2fm-rc-shop.fourthwall.com/co...
Don’t forget 2fmrc at checkout for discounts at most of your favorite shops!!
HELP SUPPORT the channel by clicking my affiliate links below and then shopping at no extra cost to you!
Thanks for any help!
AFFILIATE LINKS BELOW
Horizon Hobby affiliate link
bit.ly/3eXihxY
Amainhobbies affiliate link
bit.ly/3CurIyF
FairRc affiliate link here
shrsl.com/3qxuc
FMS Affiliate link here
www.fmshobby.com/jsVeIxtdZHBb...
Amazon affiliate link
amzn.to/3I4tQzI
RCAWD affiliate link here
rcawd.com/?ref=FaSRjm2T
Temu affiliate link here
temu.to/k/usNjJ8m2iPfZ80w
Other DISCOUNT CODES BELOW
FMS discount code is 2fmrc
$10 discount is only applicable to the purchase of complete all vehicles and accessories, and can only be used when the amount is over $50
Injora Discount code is 2fmrc05 for 5% off
MofoRC discount code is 2fmrc
Fullsendrc discount code is 2fmrc
RcAWD discount code is 2fmrcawd5 for 5% off
~-~~-~~~-~~-~
Please watch: "Injora Lights for SCX6! Super Bright & CHEAP!"
• Injora Lights for SCX6...
~-~~-~~~-~~-~ - Розваги
I forgot to mention I installed the 20% underdrive gears. Since it comes with them it’s just a given to me. It kinda feels like it needs more though. I wish it would’ve came with 20 & 30%. The 10% is almost unnoticeable to me.
I definitely understand the outrunner AND the Fusion thing. The Fusion just being soooo precise on throttle control and FOC.
On the other hand, I've been running outrunners on my crawlers for 10+ years and just absolutely love the torque-density and with the right esc, awesome low-end control. But the noise from the old esc's that uses the outrunners as speakers does get annoying.
I was thinking a Furitek Python Pro X with a 2500kv Revolver from Holmes-Hobbies would be awesome.
Never been a fan of Redcat's mediocrity on design and quality but they've kicked-it-up a notch on these new rigs and have peaked my interest.
Redcat has 9.5% under drive diff gears for the Gen 8. That's nearly 30 % total. I've done the same mods that you did and am loving my Ascent. Great vid. :)
All you together with different vehicles has to be so much fun! Loving all your great information. You tell it like it is, without the BS that others do that were sent free ones from Redcat. So obvious! 😃
It’s a blast for sure! Really appreciate the comment. I try to keep it as real as possible lol
I'm really enjoying your videos on this Redcat Ascent. Like your wheel/tire idea too. 😀 Keep'em coming. Thank You!👍
Really appreciate that! I’m definitely gonna keep rolling with it!
Been waiting for this video. I'm stuck between getting another mini with the furi wagon or another 10th scale and grabbing this. You're making my life difficult!
Very good video. Thanks for the info💪👌😉
Freakin sweet video. Love the info as always and for falling three times before it snapped I think it did damn well 😅
I want one , I can't wait to take it apart and change everything ! Isn't that weird , but that's what we do 😊
I get my ascent next week, I've got some stuff planned for it, I've watched your 24th scale content and I enjoy it so thanks for another ascent video it made me feel better about my purchase
You definitely won’t be disappointed! It’s one of the best 1/10s you can get imo. I really appreciate ya & let me know how you like the Ascent!
Wish I could have made it that day. Looks like y’all had fun.
Thanks for the vid like watching to see what i can do to my rig
Great video. Awesome tips and tricks. Thank you. I also trimmed the rear body posts. I noticed it was messing with the compression on the axle. Haven’t seen anyone mention that yet 🤷🏻♂️
Thanks! I really appreciate it
Great content, Matt! Didn't have the time this morning to watch, but good info as always. Gotta part out a few undesirables to open the stables up for this thing. So funny how many "comp guys" on social media are bashing it. Guess their $1,800 custom builds are triggered by a $300 Redcat with $300 in upgrades.
Really appreciate that! Yeah some people just gonna hate no matter what. The thing is really good for an rtr. Maybe it’s not quite as good as a fully built comp rig but like you said it’s at least half the price even when completely built and when driven by someone who knows what they are doing it’ll definitely keep up or beat most imo
I needed that un-cure adhesive remover!!! I used all the "normal" methods to remove the tires...and ended up MELTING the stock wheels and destroying the tires. Doh!
Oh man! I’ve seen a few people with melted wheels lol. I was amazed how easily this stuff removed the glue!
I was only successful at removing two tires. First I tried heat "failed" then I tried un-cure but the rims were super warped by this point so it only worked on 2.
Not acetone friendly
Great video.
Thanks! Really appreciate it
So very smoothly
Great review. Have you had a chance to compare it to the element sendero?
My friend just got his blue Ascent, I will also get the blue truck but get rid of the back bed. Looking forward to seeing your other mods for this rig...
Nice! I’m definitely gonna keep going with it. I love this truck!
I have a bunch of RC’s. This is my first crawler, it makes me wonder if I just should’ve spent the money on an better model Redcat or Axial.
And thank you for the video man and all the links because it’s going to kind of help me get this truck operating a little bit better I hope 🤞
@2FM RC I didn’t see a link for that driveshaft that you installed. Do you possibly have one?
@@danc.6663 hey sorry! This is the one I used.
amzn.to/48AVIpp
Sorry if I missed it but should I get the 1200kv or 1800 kv and what is the difference? Love your videos you got me into the hobby!
Both are grewt options, for $10 more id get the 1800kv. Either one should work. Heard the driveshaft from motor is tight fit maybe putting 1mm shims when installing back together will work to give driveshaft little room.
Check RC4WD for the inner shock springs.
This was the perfect video to have playing while installing the Fusion SE in my Ascent. Did you happen to notice the passenger shock hits the pan-hard mount on the axle if you try to lay them back further than what stock allows.
Yeah. That’s really one of my only complaints with this truck. Kinda hard to work the front end out how you want. It’s very limited in the front due to the pan hard and shock mounts on the axle. You’ll love that se! It’s crazy smooth in this truck.
@@2fmrc I was surprised how slow it creeps while still having loads of wheel speed.
Will the stock springs fit inside the shock body if you trim them down to the right height?🤔 Might be a solution to getting a softer spring on the inside of the front.
After trying pen springs and limit straps, i prefer the straps. Keeps full travel while limiting the body unloading im climbs and side hills.
While you're trimming the body will you try to get it lower or is it on the shock mounts already?
The front is definitely noticeable higher then the back no matter what mounting holes you use. I actually raised the rear body mounts a little so it doesn’t rub & it still sits lower in the back. I’m thinking about getting Desert Lizard shocks to try out I’ve had good luck with them & are very tunable. I have the 20% underdrive gears in & that’s a big help. I’m wondering if I can get those gears in metal.
Yeah I’m hoping eventually the gears will be offered in metal. I run the lizard shocks a lot. I’ve always had really good luck with them as well. I really just wanna use the stock shocks on this to see if I can lol. Everyone kinda swapped to lizards in my area so I always wanna be that guy doing something different 😆
What are the length of the top links in the back I know you said they was Capra links to .
Thanks mate .Thinking g of getting g a redcat .Who or where is the best place to get mod parts from. THANKS AGAIN from 🇨🇦 🍁
I’ve picked up all my stuff from either Redcat themselves or eBay for the Gen 9 axle parts which also fit the ascent. 1tenthrc has the servo on axle mounts.
Yep, just get out and have fun!
Would the SCX 10 wheels from Amazon fit the Redcat Fusion?thanks
Wow awesome video, and cool rc car 👍👍💯
I'm a somewhat newb to electric crawlers although done plenty in real life and fairly new to RC's in general and had been looking to buy my 1st without going all-in on my first rig. I can't believe the amount of hate that Redcat® receives and especially this Ascent from some of the "big" RC Crawler channels ans snobs (Won't mention names) Ya it isn't a perfect rig but for the money imo well worth the $289. I don't see any other brand offering a decent crawler with Portals and spares for the same money anywhere. What was the icing on the cake for me was when it continued to win in comps against guys with their $1K Vanquish customs. Guess no matter how much you spend if you can't drive it doesn't matter..
That’s definitely true! Lots of haters on this one but I absolutely love it. I think most are just hurt they wasted $1k 😆
I'd love to have some rock like that close by. Your Lucky!
What part of the country are you from?
I’m In Kentucky. Lots of this around here lol
Do you think switching from a 90mm to a 100mm shock would be beneficial on a low center of gravity rig like this? I did it on my gen8 but because it is already a taller vehicle and top heavy, i didnt see the benefit of the extra travel, it would unload sooner even on the lowest lb springs. Curious for your thoughts on this though. About to pull the trigger on one and doing my research.
I’ve had great luck with the stock shocks and really don’t think I’ll change them but I do sometimes run a little longer shock on my builds that I’m trying to get a bit more flex out of. Especially when limiting them with bands. Kinda depends on the truck for me. I really like the shorter shock on this truck but something like my poizd or gshot build I usually run 100mm
can the front shock towers be turned around? if so that should help your front shock issues.
Probably not because of how the motor is mounted to those same towers. The real issue is you can’t lay the front shocks back much because they hit the panhard mount. That’s why I may just drill a couple new holes where I want them lol
I got my son one and the only thing I keep having a problem with is the body getting stuck on the frame from the middle. Any ideas?
GO to DSM OFF-ROAD hw just came out with a carbon chassis flr the ascent he only has 5 left tho
Hi! Does it come with metal gears? Any plastic gears ? Thanks
The transmission is plastic gears. Plastic spur,plastic underdrive for the transfer case etc. The ring & pinions and portal gears are all metal.
Thanks for the reply
Why flip the rear shocks? What’s the benefit? My ascent comes mid week and if I’m gonna take them off to take the inner springs out and do the mini T spring swap, should I invert them?
It’s not much of a benefit but any extra weight down low helps so it’s kind of a habit of mine to flip them. Couldn’t really do the fronts until I did the servo on axle mod because the panhard mount was on the way.
Crazy response time. Thanks. I’m pretty pumped to get my first 1/10 crawler. As I don’t have an abundance of parts on hand to mix and match I’m trying to make the best one time purchases I can.
@@jonhowland4985 well I hope you love the ascent. Only real issue I’ve seen with them so far has been the mounts for the panhard bar. I’ve seen several broke straight out of the box. Even had one myself on my 2nd ascent I picked up. They replaced it really quick but it’s an issue obviously.
Its doing good without weight even. I don't think the other trucks can touch the Ascent for price point to performace.
I agree! Crazy how good it is. I’m gonna add the inner and outer portal covers next and see how it acts.
The Capra it needs some bigger tires and need that front end held down
Yeah both of them need weight. The red one is my father in laws and I’m about to put a fusion in it. He don’t know it yet but I’m ditching those stock plastic wheels he’s running and giving him something with some weight in it while I have it!
Whats the part number for the loai springs i googled them but didnt no what color
These are what I used
alnk.to/3yaZtjc
What tires are you using?
In this video I was running the og klr tires but I’ve really been loving the 1.9 ruptures on my ascent. They are the best tire I’ve ever ran I’d say
was sure you were going to add some underdrive. At lest the 10%
Yeah I forgot to mention that but I did add the under drive that it came with. I did the higher 20% and it still feels like it could use more imo lol. Since it’s included it almost feels like it’s not even a mod I guess so I forgot to mention it haha
Give it no time in rock Pirates will have a shock mounts for that thing
Hopefully! That or some new rails for it.
Redcat was so awful to me when I tried to order one off their website (treated me like a criminal) that I told them where to go and swore off ever owning a Redcat. I spent my money on a Fordyce instead. I still like this thing, but I won't ever own one, at least not bought new.
What wheels are you using?
It’s these wheels but in the silver color which I can’t seem to find anymore
amzn.to/3u8wWye
@@2fmrc ok thank you
@@leonelmolinajr2 no prob!