Note: if you use the ember firmware, you need to replace the adapter line by serial: adapter: ember If you experience issues, this video might help: Solving Zigbee Problems in Home Assistant | Ultimate Guide ua-cam.com/video/S59UlboptaM/v-deo.html
I ordered one through your link and received it a week ago. However, I had several issues when trying to run it in parallel (at the same time on the same HA) with Deconz and the Conbee 2 stick. I was thinking I could move devices/entities while Conbee 2 was active. I was wrong. It caused some conflicts that I never identified. I think it was more about Zigbee than it was about the sticks. But it's just a gut feeling right now. I was able to update my firmware on the E-stick using Linux, minicom, and Xmodem.
@@SmartHomeJunkie Unfortunately. Z2M is a mess for me. I had 12 devices on ZHA with Conbee2. I dropped all the devices. Removed the stick. and installed Z2M. I have Aqara and IKEA devices. The bulk of my IKEA switches are showing as unsupported by Z2M, interrogation is failing, and left useless. I moved my HA PI into a room where I could lay every device next to it. The E-stick is on a usb extension wire. So there is no radio interference. Super big mistake for me. I was hoping to get the firmware upgrade features too. Thank you for your video, but it has been really an awful experiment for me. 😀
@@traxeonic3600 That's too bad to hear. I've got my whole house paired with it. There is an issue with Ikea tradfri remotes, but I'm not sure if it's Dongle E that's. There are github issues for those reviews reported that they don't work anymore after the latest update of Z2M.
@@SmartHomeJunkie I switched out the Dongle E with the Conbee 2, set the device in z2m and serial: >- adapter: deconz and it all is instantly working. Looks like it's the "experimental" nature of the "E" that's getting me.
I followed your instructions but could not figure out why Zigbee2MQTT would immediately stop working after starting. But when I watched the complete video, I realized I had already set up ZHA integration with my Sonoff Dongle E. After removing ZHA integration, Zigbee2MQTT started working perfectly. Thanks a bunch!
@@kobedde @SmartHomeJunkie: Many thanks for your amazing video. I am starting my journey with HA. I was wondering if you could please share the steps or process to "How to disable ZHA (Zigbee Home Automation)?"
Your video really helped me in setting up my dongle with Zigbee2MQTT. I didn't realize I had the -E version and when I tried using other videos, I couldn't get the Zigbee2MQTT to run, even trying firmware updates. At some point I realized my dongle was different and discovered it to be the -E version. Then I found this video. The point that especially made this work is @4:58 when the "adapter: ezsp" is added to the serial field. Once this was done it loaded and worked! Thank you so much for the walkthrough and calling out this specific version of the dongle in the title. I also changed the Address of the mosquitto-core to the numerical IP address (I have a pretty complex VM/Synology server with Vlans)
I was stressed by failures from other UA-camrs when I saw this video. And everything works like a charm ! Many many thanks pal for your excellent work!!! The real pain for me was the wrong section ( many people says to leave it empty) of the mosquito configuration.
you made my day: after connecting the dongle out of the box I got communication errors. Checking documentation and following the troubleshooting guide there was no reason find for that. Finally the small code snippet "adapter: ezsp" in configuration file made it work. I found nothing like that in my sources... Second brilliant hint was getting close to the dongle for pairing. That made the difference in operation. Thank you for solving all my problems in one brilliant video!
Thanks for the tip to REFRESH THE BROWSER after adding Zigbee2Mqtt from the Repository! I wasted 30 minutes trying to figure that out. Another great video. Thanks.
After trying to figure out how to do this for many days, your video helped me start it up perfectly! Thank you very much brother!!! That's why I always like all your videos and am subscribed :).
Your explanations are clear. I really appreciated the pedagogy with which you indicated beforehand what you were going to do before going into the explanations. Complicated things then become simple and transparent. In your description, there is the link of the blog of your video which resumes in structured text the operating mode that you follow. Very very useful! Personally, I watched the video several times by reducing the speed and activating the subtitles in my language. You have helped me a lot. Big thanks !
Been watching YT videos all day and reading forums ALL DAY trying to figure out why my dongle wouldn't...but not one other 'expert' bothered to tell me that I needed to add that extra code for the E Dongle. You solved my problem with one video and I really appreciate it!
You are an ABSOLUTE LEGEND. Been searching from multiple forum and discussion group none of them got the solution from this, spent extra for an extension cable but no luck. THIS VIDEO IS GOLD
Ook hier in het verleden stabiliteit problemen met de Conbee2. Vorig jaar ben ik overgestapt op de de Sonoff ZB dongle en daarna nooit geen problemen meer gehad. In combinatie met de Moes ZB radiator actuator heb je meer instellingen en mogelijkheden. Dank voor je goede uitleg in je tutorials!!!
hello, I wanted to thank you very sincerely because out of 5 installation videos that I tried, you are the only one with whom it worked, again a big thank you
Best Video ever! After desperately trying for multiple times with your help it worked the first try! Subscribed immediately! Thank you again for your great explanation!
I'm so glad to hear that the video helped you and that you were able to achieve success on your first try! Thank you for your support and subscribing to the channel!
Thank you for this video, finally got it to make it work, I had the sonoff stick lying around for months and tried a few times to install Zigbee2Mqtt without success. Following your video finally I got it working!
OH, thank you! It was 2 weeks of struggle with my Moes radiator head, and I finally made it with your videos (firmware flash and this one). Your explanations are super clear. Thank you, legend
Well, I'm glad I could save you from a two-week struggle! Sometimes these things can be a real headache, but I'm here to make it a little easier for you. Keep watching and I'll keep providing clear explanations!
OMG you made my day! I kept hitting into Error: Failed to connect to the adapter (Error: SRSP - SYS - ping after 6000ms) for 3 days when I followed the other tutorials for the older P version... Now it works and the fun can start!
@@marceaum actually I have, I have to look back into my HA to look what I did. But I am pretty sure I first flashed the stick with the proper firmware. Because although I did it before, I discovers it was not done properly. I used the python method. Will get back to this if I found out exactly what I did.
Connecting to MQTT server at mqtt://core-mosquito:1883 Zigbee2MQTT: error 2022-09-10 16:10:35: MQTT failed to connect: getaddrinfo ENOTFOUND core-mosquito Doh!
Brilliant tutorial. I followed your steps (almost) exactly and it failed! But then I found I'd missed 2 spaces before the port value. Proper indentation is critical I'm discovering with HA. I corrected that and it worked!
Thanks for this easy tutorial. One problem which drove me crazy: If you use a SSD for the RP4 as boot + the Sonoff Stick, it is recognized but devices will not pair/ be discovered. This was due to the 3A limit of the power supply!! Active USB Hub and now everything works fine
Thank you both, for the video tutorial and also for the comments as I am also equipped with RP4 + SSD + the Sonoff Stick and it was not working until I added an Active USB Hub 🙂
very clear tutorial. i struggled a bit with some issue in have zigbee2mqtt working. but with ressources in description and some google search i was able to make it work.
Merci beaucoup pour votre vidéo 🙏Ca faisait plusieurs jours que je m'arrachais les cheveux pour faire fonctionner le SONOFF et j'ai trouvé votre vidéo qui m'a sauvé !!! merci encore pour vos vidéos 👍
Hi Just switched over to this new stick from the Deconz. It was actually quite easy. This is how it is done: - put new (coordinator) stick in (Dongle-E) - remove "old" stick / coordinator (Deconz)
Ik volg je al een tijdje, super duidelijke uitleg (In alle filmpjes), Iedereen zou het moeten kunnen volgen. Ik heb een werkend systeem (Draaiend op een synology NAS) in mijn huis met een conbee2 stick, Dit werkt al jaren goed. Momenteel ben ik bezig met het configureren van HA voor mijn nieuwbouw woning. Niet meer op de NAS maar op een NUC. Ik heb ook een nieuwe Zigbee 3 E gekocht, zodat ik de voorbereiding beter kan doen. Helaas heb ik problemen met de installatie van de Mosquitto broker en Zigbee2MQTT. "MQTT error: getaddrinfo ENOTFOUND core-mosuitto" Ik hoop dat ik eruit kan komen.
Als een noob met Home Assistant lukt het mij dankzij jouw video's. Heldere uitleg en rustige stem. Met ZHA kan ik de nieuwste lijn van ikea niet koppelen, echter met MQTT wel. thnx. Ik draai Home Assistant in een VM op een Synology. De Sonoff donge P werkt blijkbaar alleen als je een USB 2.0 hub ertussen zet op de USB3 poort van de NAS. Wel fijn dat deze bij amazon verkocht worden met de 3.0 firmware voor weinig geld. Scheelt weer werkt.
This is one of the best explanations to follow, I had a small issue starting the Zigbee2MQTT when using the long USB device ID. I ran the command "test -w /dev/ttyUSB0 && echo success || echo failure" which confirmed if access to the port is success or not. When I configured the port with success, port: /dev/ttyUSB0 it started working
Nice video! I was able to get my ZBDongle-E working with these instructions. I had to remove my ZHA integration, but after that my Zigbee2MQTT started to work.
Took me around an hour to figure this one out too. Great video, but you could definitely add this as a note. Zigbee2MQTT wont start if you have a set up and running ZHA integration. Fails with something like: Error: Failure send setConfigurationValue:{"type":"Buffer","data":[4,0,1,83,0,1,255,0]} at /app/node_modules/zigbee-herdsman/src/adapter/ezsp/driver/ezsp.ts:512:23 at Queue.executeNext (/app/node_modules/zigbee-herdsman/src/utils/queue.ts:32:32) EDIT: Okay now I watched the video all the way to the end and saw that you do mention it.
Рік тому
@@TheHastur667 and how did you remove the ZHA integration? I'm quite new to all this and I won't find anything but configuration.yaml and there I cannot see anything. I removed from devices the automatically detected entity but it appears again when restarting HA. On services I cannot find any related to zigbee service neither...
So it seems basically there is no difference between the "old" Sonoff stick and the current one concerning installation and usage. Gues, IF there are any performance / reliability issues so far with the new Stick, this will be a simple firmware business. As I wanted to be one the "safe road" I've ordered the old Sonoff stick to use it with Z2M. Everything works blasting fast and stable. But I have to mention that I run everything on a Lenovo NUC i5 with Proxmox as my Host. HA as Docker Container inside a LXC Container. MQTT & Zigbee2MQTT also on seperate LXC Proxmox Containers. I don't regret that step. Before I was using HAOS in a VM. The difference of speed and "snappines" is definitely noticeable. Sorry for the off topic. Keep up the good work 👍🏼
Thanks for excellent tutorial. I had to remove the `adapter: ezsp` serial setting for pairing to work. I have an 'e' Sonoff adapter. They may have updated the add-on, but not the documentation.
Got the Sonoff Zigbee E dongle now and finally everything is working. Never had any luck with the skyconnect, still doing it's job as a pure Thread modem though.
Thank you so much for this i had the ZDongle E and failed following another guide due to differeing config to this version. Only addition i did was to add " " between the user / password as would not work without - authentication failure
For testing purposes I remain my Conbee II stick on ZHA. For Z2M I used a Sonoff without E ;-) and I successfully paired an IKEA bulb, a Hue Remote and a Hue Bulb. I was able to switch the bulbs on and off, change colors and so on. But: None of these three devices were shown in the devices list of HA. I'm glad, that I was clever enough to try it with only three devices. So Z2M is an unsuccessful experiment for me. But thank you anyways for your video!
@@SmartHomeJunkie Hmm, I can't prove it right now. because I restored a prior state of my ha-server. But I try the following right now: I enabled mqtt on a Shelly relay using the ha-mqtt mosquito server. I added a user to ha. With MQTT.fx I can switch the relay and get all sensor data. Then I edited configuration.yaml and added the Shelly as switch, platform mqtt. After rebooting it doesn't show up either. The mqtt server log says, that there would be no username and password (New connection from 192.168.1.78:64016 on port 1883. error: received null username or password for unpwd check). I'm running out of ideas...
Today I got my Sonoff ZBDongle E and luckily the first video I found on UA-cam was yours. The setup of the stick worked right away and I have added 3 Philips Hue devices without problems right away. Looking forward to find more useful hints from you.
Thank you SHJ for your clear explanation, I managed with your help and a little bit of myself :-): I got stuck after configuring the Zigbee2MQTT: it couldn't be saved. After some desperation, I removed ">-" after port:. After that I was able to save and it works as it should. Afterwards I see that HA has put the ">-" back itself.
Only guide that really allowed me to setup my dongle-e with my tuya devices thanks for that. You skimp over the mosquito configuration though. For some reason mine didn't auto setup.
Very nice explanation. This is basically the same drill when adding the Sonoff ZB Bridge (tasmotized) - in the config file under serial, you set port to the IP of the bridge, and add adapter:ezsp. I use Node Red instead of HA, but installation of zigbee2mqtt is the same.
Hello, thank you very much you are live saver, I couldn't run it until you say you need to add "adapter: ezsp" I couldn't find that information thank you :)
Hello, the message below was in fact a mishap. I installed everithing a while a go and it worked good. But recently Zigbee2mqtt wont start anymore. I looked onthe net and I seemes that other people have also some problems after som recent updates (i am on 1.32.1-1 now. Did You hear anything, and If so is there a solution ?? "The add-on seems to not be ready, it might still be starting. Do you want to try again?" I get this message when I try to start manualy. "The add-on seems to not be ready, it might still be starting. Do you want to try again?" (in ieder geval hartelijk bedankt voor de verstaanbare stap voor stap uitleg)
i just bougth this stick, and a friend pointed med to your video. Everything is up and running now. But i did not find the script for ikea lamps in the description of this video. I may be blind. Thanks again.
Thanks Ed for this thorough explanation, i'm struggling to work with 2 dongle in the same time i have deConz on ZHA and the sonoff zigbee dongle but not the E, I was planning to add z2m but is not working 🤔 I will try it again after you video 😎
Super Super vid up to 4:15, but I am trying to use the Tasmota WiFi zigbee bridge and this does not seem to auto detect. I am wanting to use the WiFi bridge as the PC running HA does not have easy access and so the usb bridge would be rather buried and 'out range'. Do you have any tutorial on this ( i thought very popular coordinator ) bridge. I can find nothing more that the info you give here but your style of instruction is so much clearer. At least I got the HA zigbee2mqtt add-on installed which I failed with other vids, but not able to configure it. Thks for you time.
Interesting video again and pleased a significant increase in patreons - you certainly deserve it for the content you provide. Can I ask - what was the reason for the change from ZHA to Zigbee MQQT did you have issues? I see the there is a big difference in signal strength 5db to 20 db -has it made any difference and finally was there anything that did not pair and have you had any dropouts.
I did not move from ZHA to Zigbee2MQTT, but I have tested ZHA and found some devices that did not work well for me in ZHA, while they do work well in Zigbee2MQTT. This Dongle-E is still experimental and I do have some strange behavior now and then with my automations, but I expect it has something to do with retained messages from MQTT using my Conbee 2 stick. So I am still investigating this. In my experience, migrating to a new stick or system takes about two weeks before everything works perfect again. There's a lot to check.
Another best practice tip is to buy and use a powered USB 2.0 hub if you are using a computer with only USB 3.x ports, then connect the USB extension cable to the USB 2.0 hub instead of directly to the computer. The reason for this is that USB 3.x ports and cables cause a lot of interferance to 2.4GHz radio devices.
Thx. I use the HA Blue that only has USB-3 ports. For me, it works fine with only an extension cable. But, I know this is recommended on the Z2M site when you have issues.
Después de ver muchos videos que explicaban como hacerlo, y siempre sin éxito, por fin he conseguido dar con tu video. Me ha funcionado perfectamente, eres el único que ha explicado como configurarlo de manera correcta. Miles de GRACIAS
Thanx for your instruction. I installed the Sonoff Zigbee 3.0 Dongle Plus but I recently purchased the Sonoff Zigbee Dongle Plus-E. I want to swap the Dongle Plus for the Plus E. Can I do that just by adding the right DEVLINKS values and adding "adapter: ezsp" or do I have to re-pair all devices from scratch on.
I’m very new to HA, but one thing I can add... my HA is running in a docker container on Ubuntu. I had to add the Sonoff stick using the Add Hardware option before it could be seen in my VM. No doubt that’s obvious to the experts...
Ive been trying to get this going for a couple of days. New to HA and just setting up. So ended up reflating a fresh version of HA to the Pi and starting from scratch with a clean install. This was the first thing to setup and it still doesn't work. Just say "addon seems not to be ready......" Checked all settings and all as per your video. Very frustrating. Everything went perfect up until the end where you start Zigbee.
I had issues starting the Zigbee2MQTT, and eventually got it to work. Two points to note: 1) The username is likely case sensitive, Initially I had mixed case, and switched to lower case. 2) More importantly, I initially had special caracters in the password, and the password was 50 chars long. Only when I significantly shortened the password and removed all special chars did the service start. I did not test to pinpoint the password length threshold.
I have some non-alphanumeric characters in my password, so I don't think its all special characters however I guess there maybe some clashes with certain specials.
Thank you for another great video. You cover everything in detail, really great work. I am new to sonoff zigbee devices. After pairing the zigbee devices with the sonoff usb dongle, will the d Zigbee devices work locally or still require internet ? Kindly reply
Just FYI, if you use a passphrase for the mqtt-user, you will need to re-add it in the settings section inside Zigbee2MQTT as for some reason it does not like "-" when putting it in the configuration part of the add-on. Now it works really well. Now I want to swap out all of my wifi devices for zigbee.
Thanks so much for the great video ... one question though ... I have tried to connect the broker and when I click on: Do you want to configure Home Assistant to connect to the MQTT broker provided by the add-on Mosquitto broker? and when I do it says' Failed to connect" can't seem to see any obvious reason. I don't suppose anyone on this thread knows why do they?
Great video! I made it work well, but I still have 2 big problems: 1) battery powered Zigbee switches loses connection all the time. Mainly the Robb Smart remote wall switches are not working. 2) My Philips Hue devices are not recognized. Sometimes it takes a couple of days but some devices are not discovered. I factory reset all devices but no luck. Do you have any tips or can you help me?
Hi, I found your "old" video how to flash the Sonoff 3.0 - excellent! I ordered and received the stick today and realize, that the flashing does not work like described in the other video. I would like to use the Stick 3.0 E in my ioBroker installation. Unfortunately it does not connect and beeing a newbi I have no idea how to solve the problem. Any hints or links for the stick 3.0 E in ioBroker? Thanks in advice!
Hi. Thanks for video. May I have a question, please. Maybe it's easy or no worth to have a question.... 😀 I already have Zigbee2MQTT in a docker. Can I migrate all devices to Zigbee2MQTT to the Zigbee2MQTT addon?
What a great video - I was getting worried that Zigbee2MQTT wasnt starting up with my Dongle-E, but following your tutorial it has all started working - none of the other instructions mentioned setting up the mqtt section of the config, and they all had me scrabbling round in the console to find the port address. By contrast, you had me up and running in 10 minutes - thank you! Now that I've got Zigbee working, could you follow up with a video about Zigbee routers/repeaters - should I be buying the Ikea TRÅDFRI or another ZBDongle-E and flash that with the router firmware?
Hi Ed, thanks a lot for the video, this should do the trick. At minute 09.10 you give a pro tip for putting Ikea lamps in pairing mode, but I don't see the script in the description of the video! Am I not looking properly or did you forget to add that?
Great video, I'm new to HA and used your video to get access to my Zigbee devices. That said, do I still need to configure the Sonoff Zigbee 3.0 USB Dongle Plus that has now been discovered in my system?
I followed your guide but it seems Zigbee2MQTT can't connect to mosquitto. Can you help? Here's the log part: 2024-01-15 21:37:41: mosquitto version 2.0.18 running 2024-01-15 21:37:42: New connection from 127.0.0.1:48166 on port 1883. 2024-01-15 21:37:42: Client disconnected due to protocol error. [21:37:44] INFO: Successfully send discovery information to Home Assistant. [21:37:45] INFO: Successfully send service information to the Supervisor. 2024-01-15 21:38:38: New connection from 172.30.32.1:38943 on port 1883. 2024-01-15 21:38:38: New client connected from 172.30.32.1:38943 as 7q6FO8Rtm3Wn6nlV9cmlXS (p2, c1, k60, u'homeassistant'). 2024-01-15 21:38:40: Client 7q6FO8Rtm3Wn6nlV9cmlXS disconnected. 2024-01-15 21:38:40: New connection from 172.30.32.1:41041 on port 1883. 2024-01-15 21:38:40: New client connected from 172.30.32.1:41041 as 4bfJYoLdQiDuCh84Weihdy (p2, c1, k60, u'homeassistant'). 2024-01-15 21:39:20: New connection from 172.30.32.2:34176 on port 1883. 2024-01-15 21:39:20: Client closed its connection.
Thanks for your videos. I have a question about the Zigbee network key which is (default) being used. I'm using the Skyconnect coordinator and first I have used ZHA for a brief period. Then I migrated to Zigbee2MQTT and i'm completely happy with all offered features. Is there a way to find out which Zigbee network key is being used? I'm a bit confused, because it seems that Zigbee2MQTT standard not generates an unique Zigbee network key, but maybe maybe I haven't read enough yet about that topic.
I bought it after seeing your video, but I can't match everything. Sonoff presence sensors(SNZB-03 and SNZB-04) do not match. They are detected, but not supported. Also 2 Philips hue rgb bulbs in the same way. I will wait for a more stable firmware. Add that I haven't any problem with conbeeII.
Note: if you use the ember firmware, you need to replace the adapter line by
serial:
adapter: ember
If you experience issues, this video might help: Solving Zigbee Problems in Home Assistant | Ultimate Guide
ua-cam.com/video/S59UlboptaM/v-deo.html
I ordered one through your link and received it a week ago. However, I had several issues when trying to run it in parallel (at the same time on the same HA) with Deconz and the Conbee 2 stick. I was thinking I could move devices/entities while Conbee 2 was active. I was wrong. It caused some conflicts that I never identified. I think it was more about Zigbee than it was about the sticks. But it's just a gut feeling right now. I was able to update my firmware on the E-stick using Linux, minicom, and Xmodem.
@@traxeonic3600 You can try to change the channel of one stick, maybe they interfere.
@@SmartHomeJunkie Unfortunately. Z2M is a mess for me. I had 12 devices on ZHA with Conbee2. I dropped all the devices. Removed the stick. and installed Z2M. I have Aqara and IKEA devices. The bulk of my IKEA switches are showing as unsupported by Z2M, interrogation is failing, and left useless. I moved my HA PI into a room where I could lay every device next to it. The E-stick is on a usb extension wire. So there is no radio interference. Super big mistake for me. I was hoping to get the firmware upgrade features too. Thank you for your video, but it has been really an awful experiment for me. 😀
@@traxeonic3600 That's too bad to hear. I've got my whole house paired with it. There is an issue with Ikea tradfri remotes, but I'm not sure if it's Dongle E that's. There are github issues for those reviews reported that they don't work anymore after the latest update of Z2M.
@@SmartHomeJunkie I switched out the Dongle E with the Conbee 2, set the device in z2m and serial: >- adapter: deconz and it all is instantly working. Looks like it's the "experimental" nature of the "E" that's getting me.
I followed your instructions but could not figure out why Zigbee2MQTT would immediately stop working after starting. But when I watched the complete video, I realized I had already set up ZHA integration with my Sonoff Dongle E. After removing ZHA integration, Zigbee2MQTT started working perfectly. Thanks a bunch!
Superb that you got it to work!
Thanks for the tip. I had made the same mistake and found the solution thanks to your command. 👍
@@kobedde @SmartHomeJunkie: Many thanks for your amazing video. I am starting my journey with HA. I was wondering if you could please share the steps or process to "How to disable ZHA (Zigbee Home Automation)?"
@@dilpreetsohanpal3062 Could you already find out how to disable ZHA?
same here! Thanks for the comment this savedme.
Your video really helped me in setting up my dongle with Zigbee2MQTT. I didn't realize I had the -E version and when I tried using other videos, I couldn't get the Zigbee2MQTT to run, even trying firmware updates. At some point I realized my dongle was different and discovered it to be the -E version. Then I found this video. The point that especially made this work is @4:58 when the "adapter: ezsp" is added to the serial field. Once this was done it loaded and worked!
Thank you so much for the walkthrough and calling out this specific version of the dongle in the title. I also changed the Address of the mosquitto-core to the numerical IP address (I have a pretty complex VM/Synology server with Vlans)
hey, thanks for the comment. did you have any trouble with pairing it or it not being able to recognize some device features?
@@nateF888 once I realized my initial issue, everything went well. No issues with the hue or other zigbee devices
Thanks a lot man! I was struggling to configure my adapter because of the lack of the adapter information with the port.
Thank you for your support! 🙏🏻 🙏🏻 🙏🏻
I FINALLY have Zigbee2MQTT running. No more 502: Bad Gateway errors!
Thank you for your support and great to hear!!!
I was stressed by failures from other UA-camrs when I saw this video. And everything works like a charm ! Many many thanks pal for your excellent work!!! The real pain for me was the wrong section ( many people says to leave it empty) of the mosquito configuration.
you made my day: after connecting the dongle out of the box I got communication errors.
Checking documentation and following the troubleshooting guide there was no reason find for that.
Finally the small code snippet
"adapter: ezsp" in configuration file made it work.
I found nothing like that in my sources...
Second brilliant hint was getting close to the dongle for pairing.
That made the difference in operation.
Thank you for solving all my problems in one brilliant video!
Thank you!
I had exactly this issue as well!
Thanks for the tip to REFRESH THE BROWSER after adding Zigbee2Mqtt from the Repository! I wasted 30 minutes trying to figure that out. Another great video. Thanks.
Great to hear that it helped!
Hi, i was a min. away from jumping off the roof, i was struggling to configure my dongle-E for almost 3 days until i found you movie. thanks a lot!!!
Awesome!
After trying to figure out how to do this for many days, your video helped me start it up perfectly! Thank you very much brother!!! That's why I always like all your videos and am subscribed :).
Thank you!!!
Very well done. I installed no problems. Thanks!
Thank you for your support!
Thanks to all that said rebooting the Pi would solve the problem. I actually unplugged and then plugged it back in. Thank you again.
Your explanations are clear. I really appreciated the pedagogy with which you indicated beforehand what you were going to do before going into the explanations. Complicated things then become simple and transparent.
In your description, there is the link of the blog of your video which resumes in structured text the operating mode that you follow. Very very useful! Personally, I watched the video several times by reducing the speed and activating the subtitles in my language.
You have helped me a lot. Big thanks !
Thank you so much for this really nice comment! 🙏🏻
Been watching YT videos all day and reading forums ALL DAY trying to figure out why my dongle wouldn't...but not one other 'expert' bothered to tell me that I needed to add that extra code for the E Dongle. You solved my problem with one video and I really appreciate it!
You are an ABSOLUTE LEGEND. Been searching from multiple forum and discussion group none of them got the solution from this, spent extra for an extension cable but no luck. THIS VIDEO IS GOLD
Thanks! 🙏🏻
Ook hier in het verleden stabiliteit problemen met de Conbee2. Vorig jaar ben ik overgestapt op de de Sonoff ZB dongle en daarna nooit geen problemen meer gehad. In combinatie met de Moes ZB radiator actuator heb je meer instellingen en mogelijkheden. Dank voor je goede uitleg in je tutorials!!!
received my Sonoff Zigbee 3.0 USB dongle on hour ago. thanks to this video, got my first ikea light ( GU10 spot) running already!!!
Brilliant!!!
hello, I wanted to thank you very sincerely because out of 5 installation videos that I tried, you are the only one with whom it worked, again a big thank you
Great that it helped!
Best Video ever! After desperately trying for multiple times with your help it worked the first try! Subscribed immediately! Thank you again for your great explanation!
I'm so glad to hear that the video helped you and that you were able to achieve success on your first try! Thank you for your support and subscribing to the channel!
I had to go through half a dozen different firmwares before I finally got it working, but now it works. Thank you so much for making this video.
I'm glad it helped!
Which one are you using?
@@rein2523 Currently something that has filename sonoff_zbdonglee_zigbee_ncp_8.0.2.0_115200_sw_flow.gbl
Man I would never be able to make this stick work without your video. Thanks a lot :)
You just saved me multiple hours of troubleshoot by explaining everything step by step. I was able to find few things I did wrong, thank you so much!
Thank you for this video, finally got it to make it work, I had the sonoff stick lying around for months and tried a few times to install Zigbee2Mqtt without success. Following your video finally I got it working!
I was struggling to set this up. Tried following several tutorials. Finally, this one worked! Thanks a lot.
It saved my life, I saw several Brazilian tutorials and none of them helped, thank you very much. ♥
OH, thank you! It was 2 weeks of struggle with my Moes radiator head, and I finally made it with your videos (firmware flash and this one). Your explanations are super clear. Thank you, legend
Well, I'm glad I could save you from a two-week struggle! Sometimes these things can be a real headache, but I'm here to make it a little easier for you. Keep watching and I'll keep providing clear explanations!
OMG you made my day!
I kept hitting into Error: Failed to connect to the adapter (Error: SRSP - SYS - ping after 6000ms) for 3 days when I followed the other tutorials for the older P version... Now it works and the fun can start!
Great to hear that I made someone's day today! 👍🏻
I am still hitting the Error: SRSP - SYS - ping after 6000ms, even with this great tutorial..... frustrating at the least
@@cbosjesman I can only say, look at the website that the log file refers to. You might have a specific issue that is mentioned there.
@@cbosjesman Hello, I have exactly the same problem and the same dongle as you. Have you found a solution?
@@marceaum actually I have, I have to look back into my HA to look what I did. But I am pretty sure I first flashed the stick with the proper firmware. Because although I did it before, I discovers it was not done properly. I used the python method. Will get back to this if I found out exactly what I did.
Just got this device in the mail today, I was thrilled to find your video on this exact topic I needed. You are amazing!
That's great to hear!
Connecting to MQTT server at mqtt://core-mosquito:1883
Zigbee2MQTT: error 2022-09-10 16:10:35: MQTT failed to connect: getaddrinfo ENOTFOUND core-mosquito
Doh!
Somehow I missed the second T in core-mosquitto.
@@stevetb7777 Great that you got it to work!
I tried install Zigbee2MQTT and pair the Sonoff Dongle-E with others video but was not successful, until I follow your instruction. Thank you!
Looks like my video was the missing puzzle piece! Don't worry, I won't tell the others that you needed my help. Your secret is safe with me!
Finally, I managed to pair my Zigbee-e with your help, thanks!
Glad I could help!
Brilliant tutorial. I followed your steps (almost) exactly and it failed! But then I found I'd missed 2 spaces before the port value. Proper indentation is critical I'm discovering with HA. I corrected that and it worked!
Excellent!
Thanks for this easy tutorial. One problem which drove me crazy:
If you use a SSD for the RP4 as boot + the Sonoff Stick, it is recognized but devices will not pair/ be discovered. This was due to the 3A limit of the power supply!! Active USB Hub and now everything works fine
Thank you both, for the video tutorial and also for the comments as I am also equipped with RP4 + SSD + the Sonoff Stick and it was not working until I added an Active USB Hub 🙂
very clear tutorial. i struggled a bit with some issue in have zigbee2mqtt working. but with ressources in description and some google search i was able to make it work.
That's awesome!
Merci beaucoup pour votre vidéo 🙏Ca faisait plusieurs jours que je m'arrachais les cheveux pour faire fonctionner le SONOFF et j'ai trouvé votre vidéo qui m'a sauvé !!! merci encore pour vos vidéos 👍
De rien! 👍🏻
Hi
Just switched over to this new stick from the Deconz. It was actually quite easy. This is how it is done:
- put new (coordinator) stick in (Dongle-E)
- remove "old" stick / coordinator (Deconz)
Ik volg je al een tijdje, super duidelijke uitleg (In alle filmpjes), Iedereen zou het moeten kunnen volgen. Ik heb een werkend systeem (Draaiend op een synology NAS) in mijn huis met een conbee2 stick, Dit werkt al jaren goed.
Momenteel ben ik bezig met het configureren van HA voor mijn nieuwbouw woning. Niet meer op de NAS maar op een NUC. Ik heb ook een nieuwe Zigbee 3 E gekocht, zodat ik de voorbereiding beter kan doen. Helaas heb ik problemen met de installatie van de Mosquitto broker en Zigbee2MQTT. "MQTT error: getaddrinfo ENOTFOUND core-mosuitto"
Ik hoop dat ik eruit kan komen.
Het moet core-mosquitto zijn en niet core-mosuitto
Als een noob met Home Assistant lukt het mij dankzij jouw video's. Heldere uitleg en rustige stem. Met ZHA kan ik de nieuwste lijn van ikea niet koppelen, echter met MQTT wel. thnx.
Ik draai Home Assistant in een VM op een Synology. De Sonoff donge P werkt blijkbaar alleen als je een USB 2.0 hub ertussen zet op de USB3 poort van de NAS. Wel fijn dat deze bij amazon verkocht worden met de 3.0 firmware voor weinig geld. Scheelt weer werkt.
Fijn om te horen dat mijn videos je helpen!
This is one of the best explanations to follow, I had a small issue starting the Zigbee2MQTT when using the long USB device ID. I ran the command "test -w /dev/ttyUSB0 && echo success || echo failure" which confirmed if access to the port is success or not. When I configured the port with success, port: /dev/ttyUSB0 it started working
Thank you so much for this video! Now our house has its first few smart bulbs! :)
Thank you for your kind words! I'm thrilled that the video helped you brighten up your home with smart technology!
great video. had some trouble with the configuration until i saw how you did it in yours
That's great to hear!
you sir are a genius and I can now stop pulling my hair out. Thank you so much.
Outstanding video, which helped me get my setup working. Thanks.
That's awesome to hear!
Nice video! I was able to get my ZBDongle-E working with these instructions. I had to remove my ZHA integration, but after that my Zigbee2MQTT started to work.
Took me around an hour to figure this one out too. Great video, but you could definitely add this as a note. Zigbee2MQTT wont start if you have a set up and running ZHA integration. Fails with something like:
Error: Failure send setConfigurationValue:{"type":"Buffer","data":[4,0,1,83,0,1,255,0]} at /app/node_modules/zigbee-herdsman/src/adapter/ezsp/driver/ezsp.ts:512:23 at Queue.executeNext (/app/node_modules/zigbee-herdsman/src/utils/queue.ts:32:32)
EDIT: Okay now I watched the video all the way to the end and saw that you do mention it.
@@TheHastur667 and how did you remove the ZHA integration? I'm quite new to all this and I won't find anything but configuration.yaml and there I cannot see anything. I removed from devices the automatically detected entity but it appears again when restarting HA. On services I cannot find any related to zigbee service neither...
@@TheHastur667 How did you disable ZHA?
Bedankt!
Dank je wel voor je support!
So it seems basically there is no difference between the "old" Sonoff stick and the current one concerning installation and usage.
Gues, IF there are any performance / reliability issues so far with the new Stick, this will be a simple firmware business.
As I wanted to be one the "safe road" I've ordered the old Sonoff stick to use it with Z2M.
Everything works blasting fast and stable. But I have to mention that I run everything on a Lenovo NUC i5 with Proxmox as my Host.
HA as Docker Container inside a LXC Container. MQTT & Zigbee2MQTT also on seperate LXC Proxmox Containers.
I don't regret that step. Before I was using HAOS in a VM. The difference of speed and "snappines" is definitely noticeable.
Sorry for the off topic. Keep up the good work 👍🏼
Is that difficult to do? I have ha on VM. A bit slow...
@@caspersn1971 no it's not
@@hammerlized can you recommend a turtorial?
Thanks for excellent tutorial.
I had to remove the `adapter: ezsp` serial setting for pairing to work.
I have an 'e' Sonoff adapter. They may have updated the add-on, but not the documentation.
🤔 That shouldn't be the case. Are you sure that that setting is also removed from the configuration.yaml of Zigbee2MQTT?
Got the Sonoff Zigbee E dongle now and finally everything is working. Never had any luck with the skyconnect, still doing it's job as a pure Thread modem though.
Thank you so much for this i had the ZDongle E and failed following another guide due to differeing config to this version. Only addition i did was to add " " between the user / password as would not work without - authentication failure
For testing purposes I remain my Conbee II stick on ZHA. For Z2M I used a Sonoff without E ;-) and I successfully paired an IKEA bulb, a Hue Remote and a Hue Bulb. I was able to switch the bulbs on and off, change colors and so on. But: None of these three devices were shown in the devices list of HA. I'm glad, that I was clever enough to try it with only three devices. So Z2M is an unsuccessful experiment for me. But thank you anyways for your video!
If they don't show up in Home Assistant, then probably you filled in the wrong credentials or mqtt server in your Zigbee2MQTT configuration.
@@SmartHomeJunkie
Hmm, I can't prove it right now. because I restored a prior state of my ha-server. But I try the following right now: I enabled mqtt on a Shelly relay using the ha-mqtt mosquito server. I added a user to ha. With MQTT.fx I can switch the relay and get all sensor data.
Then I edited configuration.yaml and added the Shelly as switch, platform mqtt. After rebooting it doesn't show up either. The mqtt server log says, that there would be no username and password (New connection from 192.168.1.78:64016 on port 1883.
error: received null username or password for unpwd check).
I'm running out of ideas...
MANY MANY thanks!!!! i had a problem and only your video solved it.....
That is great to hear!
Today I got my Sonoff ZBDongle E and luckily the first video I found on UA-cam was yours. The setup of the stick worked right away and I have added 3 Philips Hue devices without problems right away. Looking forward to find more useful hints from you.
That's awesome!
Thank you SHJ for your clear explanation, I managed with your help and a little bit of myself :-): I got stuck after configuring the Zigbee2MQTT: it couldn't be saved. After some desperation, I removed ">-" after port:. After that I was able to save and it works as it should. Afterwards I see that HA has put the ">-" back itself.
Only guide that really allowed me to setup my dongle-e with my tuya devices thanks for that. You skimp over the mosquito configuration though. For some reason mine didn't auto setup.
Not sure why it wouldn't automatically setup. 🤷🏼 Works here every time. There must be something different in your setup compared to mine.
@@SmartHomeJunkie That is odd. Anyway its all working now. Success! :)
Very nice explanation. This is basically the same drill when adding the Sonoff ZB Bridge (tasmotized) - in the config file under serial, you set port to the IP of the bridge, and add adapter:ezsp. I use Node Red instead of HA, but installation of zigbee2mqtt is the same.
what does adapter: ezsp do?
@@MarinDzhigarov It tells zigbee2mqtt that you are using a bridge of some sort other than a directly supported (firmware flashet) USB receiver.
Thanks for the video mate ! Helped me get my dongle setup and running ... i have subbed to the channel for more helpful videos in the future
Thank you 🙏🏻
Superb step by step guide for the Sonoff Zigbee 3.0. Thanks a lot, and keep up the great work you do!
Thank you so much!
Hello, thank you very much you are live saver, I couldn't run it until you say you need to add "adapter: ezsp" I couldn't find that information thank you :)
Great to hear that it helped!
Hello,
the message below was in fact a mishap.
I installed everithing a while a go and it worked good.
But recently Zigbee2mqtt wont start anymore. I looked onthe net and I seemes that other people have also some problems after som recent updates (i am on 1.32.1-1 now. Did You hear anything, and If so is there a solution ??
"The add-on seems to not be ready, it might still be starting. Do you want to try again?"
I get this message when I try to start manualy.
"The add-on seems to not be ready, it might still be starting. Do you want to try again?"
(in ieder geval hartelijk bedankt voor de verstaanbare stap voor stap uitleg)
Super helpful! Finally connected my Dongle E to HA!
That's awesome to hear!
i just bougth this stick, and a friend pointed med to your video. Everything is up and running now. But i did not find the script for ikea lamps in the description of this video. I may be blind. Thanks again.
It's in the ko-fi link in the description.
Hey Ed,
Another great video from you!
Did you manage to have the RTCGQ11LM detect any motion?
Yes, I have multiple in my home.
Best tutorial I could find. Thanks!
Doing great things for the community.
Thank you.
I used this guide for skyconnect and it worked great! I’d like to switch to a POE dongle instead. What would be the best way to do that?
Thanks Ed for this thorough explanation, i'm struggling to work with 2 dongle in the same time i have deConz on ZHA and the sonoff zigbee dongle but not the E,
I was planning to add z2m but is not working 🤔
I will try it again after you video 😎
Let me know Sevag!
@@SmartHomeJunkie thanks Ed, I will 👍🏻
Super Super vid up to 4:15, but I am trying to use the Tasmota WiFi zigbee bridge and this does not seem to auto detect. I am wanting to use the WiFi bridge as the PC running HA does not have easy access and so the usb bridge would be rather buried and 'out range'. Do you have any tutorial on this ( i thought very popular coordinator ) bridge. I can find nothing more that the info you give here but your style of instruction is so much clearer. At least I got the HA zigbee2mqtt add-on installed which I failed with other vids, but not able to configure it. Thks for you time.
Thank you for this. Informative, to the point and worked on first try following instructions.
Great to hear!
Works perfectly!!! Thanks!! I have a tuya hub too. Can i add it on MQTT via zigbee mesh too?? I try pair, but don't apear.
Interesting video again and pleased a significant increase in patreons - you certainly deserve it for the content you provide. Can I ask - what was the reason for the change from ZHA to Zigbee MQQT did you have issues? I see the there is a big difference in signal strength 5db to 20 db -has it made any difference and finally was there anything that did not pair and have you had any dropouts.
I did not move from ZHA to Zigbee2MQTT, but I have tested ZHA and found some devices that did not work well for me in ZHA, while they do work well in Zigbee2MQTT.
This Dongle-E is still experimental and I do have some strange behavior now and then with my automations, but I expect it has something to do with retained messages from MQTT using my Conbee 2 stick. So I am still investigating this. In my experience, migrating to a new stick or system takes about two weeks before everything works perfect again. There's a lot to check.
Another best practice tip is to buy and use a powered USB 2.0 hub if you are using a computer with only USB 3.x ports, then connect the USB extension cable to the USB 2.0 hub instead of directly to the computer. The reason for this is that USB 3.x ports and cables cause a lot of interferance to 2.4GHz radio devices.
Thx. I use the HA Blue that only has USB-3 ports. For me, it works fine with only an extension cable. But, I know this is recommended on the Z2M site when you have issues.
Thanks for the video, quick question, so unlike Sonoff ZBDongle P, ZBDongle E does not need any flash. right?
Indeed.
Después de ver muchos videos que explicaban como hacerlo, y siempre sin éxito, por fin he conseguido dar con tu video. Me ha funcionado perfectamente, eres el único que ha explicado como configurarlo de manera correcta.
Miles de GRACIAS
Thanx for your instruction. I installed the Sonoff Zigbee 3.0 Dongle Plus but I recently purchased the Sonoff Zigbee Dongle Plus-E. I want to swap the Dongle Plus for the Plus E. Can I do that just by adding the right DEVLINKS values and adding "adapter: ezsp" or do I have to re-pair all devices from scratch on.
You deserve a cookie! It worked!
Thank you. I was really hungry 😉
I’m very new to HA, but one thing I can add... my HA is running in a docker container on Ubuntu. I had to add the Sonoff stick using the Add Hardware option before it could be seen in my VM. No doubt that’s obvious to the experts...
Thanks for adding this. This will no doubt help other people.
Bravo!!! My English no so good like I wish, but your videos are very very easy to understand
Ive been trying to get this going for a couple of days. New to HA and just setting up. So ended up reflating a fresh version of HA to the Pi and starting from scratch with a clean install. This was the first thing to setup and it still doesn't work. Just say "addon seems not to be ready......" Checked all settings and all as per your video. Very frustrating. Everything went perfect up until the end where you start Zigbee.
Thanks for your video.
So there's no need to flash it?
No, but that also counts for the older stick. There isn't even update firmware available at the moment.
I had issues starting the Zigbee2MQTT, and eventually got it to work. Two points to note:
1) The username is likely case sensitive, Initially I had mixed case, and switched to lower case.
2) More importantly, I initially had special caracters in the password, and the password was 50 chars long. Only when I significantly shortened the password and removed all special chars did the service start. I did not test to pinpoint the password length threshold.
I have some non-alphanumeric characters in my password, so I don't think its all special characters however I guess there maybe some clashes with certain specials.
These tutorials are far more detailed than on other HA You2bers :)
Thank you for your compliment!
Thank you for another great video. You cover everything in detail, really great work.
I am new to sonoff zigbee devices. After pairing the zigbee devices with the sonoff usb dongle, will the d
Zigbee devices work locally or still require internet ? Kindly reply
They work locally after that.
@@SmartHomeJunkie thank you
You are an absolute legend!!! Thanks so much!
Thanks!
Just FYI, if you use a passphrase for the mqtt-user, you will need to re-add it in the settings section inside Zigbee2MQTT as for some reason it does not like "-" when putting it in the configuration part of the add-on. Now it works really well. Now I want to swap out all of my wifi devices for zigbee.
Okay. In my case this was not needed. Not sure why you had to do it that way. But great that it works for you!
that 'adapter: ezsp' bit did the trick for me for the E model. Thanks a lot.
Thanks so much for the great video ... one question though ... I have tried to connect the broker and when I click on:
Do you want to configure Home Assistant to connect to the MQTT broker provided by the add-on Mosquitto broker?
and when I do it says' Failed to connect" can't seem to see any obvious reason. I don't suppose anyone on this thread knows why do they?
Great video! I made it work well, but I still have 2 big problems:
1) battery powered Zigbee switches loses connection all the time. Mainly the Robb Smart remote wall switches are not working.
2) My Philips Hue devices are not recognized. Sometimes it takes a couple of days but some devices are not discovered. I factory reset all devices but no luck.
Do you have any tips or can you help me?
Hi, I found your "old" video how to flash the Sonoff 3.0 - excellent! I ordered and received the stick today and realize, that the flashing does not work like described in the other video.
I would like to use the Stick 3.0 E in my ioBroker installation. Unfortunately it does not connect and beeing a newbi I have no idea how to solve the problem. Any hints or links for the stick 3.0 E in ioBroker?
Thanks in advice!
I do not use ioBroker unfortunately, so I don't know how to do that.
@@SmartHomeJunkie
Ok, Thanks!
Hi. Thanks for video. May I have a question, please. Maybe it's easy or no worth to have a question.... 😀
I already have Zigbee2MQTT in a docker. Can I migrate all devices to Zigbee2MQTT to the Zigbee2MQTT addon?
What a great video - I was getting worried that Zigbee2MQTT wasnt starting up with my Dongle-E, but following your tutorial it has all started working - none of the other instructions mentioned setting up the mqtt section of the config, and they all had me scrabbling round in the console to find the port address. By contrast, you had me up and running in 10 minutes - thank you!
Now that I've got Zigbee working, could you follow up with a video about Zigbee routers/repeaters - should I be buying the Ikea TRÅDFRI or another ZBDongle-E and flash that with the router firmware?
Thanks. Basically every mains powered device like lightbulbs act as a router device.
Hi Ed, thanks a lot for the video, this should do the trick. At minute 09.10 you give a pro tip for putting Ikea lamps in pairing mode, but I don't see the script in the description of the video! Am I not looking properly or did you forget to add that?
It is there. See ko-fi.com/s/b0feb57007
thanks, downloaded it... but where to find twe write device ID in HA?
@@SmartHomeJunkie
Great job on the video, very clear and easy to follow.
Great video! Super helpful for getting my IR Blaster connected.
Awesome! Now that your IR Blaster is connected, you can officially call yourself a remote control wizard!
hi man,
great video
I am struggling with my E dongle, cant seem to add the adapter: ezsp to the serial configuration
any advice?
No idea why. You can try adding it to the configuration.yaml of Zignbee2MQTT (in the zigbee2mqtt folder) on your server.
Great video, I'm new to HA and used your video to get access to my Zigbee devices. That said, do I still need to configure the Sonoff Zigbee 3.0 USB Dongle Plus that has now been discovered in my system?
No, you shouldn't. You should disable that one.
Can I use this stick with a usb hub? Or does it need to be plugged into my raspberry?
Thank You!!
You need to use a USB extension cable to get this to work properly.
@@SmartHomeJunkie Thank You! Please keep up your fantastic work :)
I followed your guide but it seems Zigbee2MQTT can't connect to mosquitto. Can you help? Here's the log part:
2024-01-15 21:37:41: mosquitto version 2.0.18 running
2024-01-15 21:37:42: New connection from 127.0.0.1:48166 on port 1883.
2024-01-15 21:37:42: Client disconnected due to protocol error.
[21:37:44] INFO: Successfully send discovery information to Home Assistant.
[21:37:45] INFO: Successfully send service information to the Supervisor.
2024-01-15 21:38:38: New connection from 172.30.32.1:38943 on port 1883.
2024-01-15 21:38:38: New client connected from 172.30.32.1:38943 as 7q6FO8Rtm3Wn6nlV9cmlXS (p2, c1, k60, u'homeassistant').
2024-01-15 21:38:40: Client 7q6FO8Rtm3Wn6nlV9cmlXS disconnected.
2024-01-15 21:38:40: New connection from 172.30.32.1:41041 on port 1883.
2024-01-15 21:38:40: New client connected from 172.30.32.1:41041 as 4bfJYoLdQiDuCh84Weihdy (p2, c1, k60, u'homeassistant').
2024-01-15 21:39:20: New connection from 172.30.32.2:34176 on port 1883.
2024-01-15 21:39:20: Client closed its connection.
La vidéo parfaite !!! Cela a fonctionné... à la seconde tentative ! J'ai dû raté un p'tit truc :-)
Awesome!
Thanks for your videos. I have a question about the Zigbee network key which is (default) being used. I'm using the Skyconnect coordinator and first I have used ZHA for a brief period. Then I migrated to Zigbee2MQTT and i'm completely happy with all offered features. Is there a way to find out which Zigbee network key is being used? I'm a bit confused, because it seems that Zigbee2MQTT standard not generates an unique Zigbee network key, but maybe maybe I haven't read enough yet about that topic.
I bought it after seeing your video, but I can't match everything. Sonoff presence sensors(SNZB-03 and SNZB-04) do not match. They are detected, but not supported. Also 2 Philips hue rgb bulbs in the same way. I will wait for a more stable firmware. Add that I haven't any problem with conbeeII.
Today, a new version of Zigbee2MQTT is released which seems to work far more stable with this Dongle now.
@@SmartHomeJunkie I tried now, but just a little bit better. My philips hue rgb bulb not work yet and not work battery sensor of SNZB-03 and SNZB-04.
@@NicolaPatruno Philips Hue works here without any issues. I guess it's still in the experimental phase.
Thank you so much for this information! It was exactly what I needed 😁.
Awesome! Happy to help, keep rocking!