How to operate guillotine machine/ paper cutting machine

Поділитися
Вставка
  • Опубліковано 28 січ 2025

КОМЕНТАРІ • 35

  • @HmSagor-bi8se
    @HmSagor-bi8se Місяць тому +1

    এইটা কোন জায়গায়

  • @gizmo5586
    @gizmo5586 Рік тому +3

    This machine is programmable. Why does he use a sample for sizing ?

    • @alexxander7289
      @alexxander7289 Місяць тому

      the machine is programmable up to a certain point. this shop is using an 8mm dead gutter and a ZERO mm middle line gutter on their print. They are using a bulk paper product and getting x3 batches of printable media. Notice on his first production BULK cut, the operator used a template. And on the other 2 cuts he didnt use a template. When getting 3 or 4 batches from a bulk paper run, you need to allow for some "gutter" cuts. Using a programmable machine cannot do this with bulk cuts. Also the typesetter operator might be the reason for this. They might request that the paper be bulk cut like this, especially if they are printing duplex.

  • @alexxander7289
    @alexxander7289 Місяць тому +1

    hand should never be under paper pressure plate OR blade even while not "in use", especially not with hand touching panel. I realize he needs to press it fimly but should be using a feeder shim. The feeder shim is seen to his left not in use. Also if you look far right about half way on the verticle axis, there are two holes. This machine was not properly installed. Whoever is the operations director needs to be let go. This cutter is not ready for production work.

  • @YachinMiya
    @YachinMiya 4 місяці тому +3

    আমার একটা কাটিং ম্যান এর চাকরি দরকার

  • @Loki1815
    @Loki1815 Рік тому +3

    OK, let's start from the very beginning!
    I take it someone else is going to knock up the stock later!!!!
    Why are you moving the back gauge manually but not setting the mark as program mark?
    Why turn the block completely around? Are you not going to follow the Lay and Grip?
    Smashing an A0 stack to the back gauge and it won't be long until the back gauge is out of square!
    Why are you cutting the stack to a Previous copy not the size x3 and then struggle to move stack out the way to retrieve the cut stock?
    And then cut off excess trim again before dividing the sheet size in two?
    Very bizarre!

    • @alexxander7289
      @alexxander7289 Місяць тому

      hes turning it arounf to get a perfect 0 degree across his back. but I agreee, that should have been done before even starting.

  • @girishpatil7174
    @girishpatil7174 4 місяці тому +1

    Sir machine to mil jayega lekin xeros paper ka Raw material kaha se milega

  • @WaqarAhmad-ch9hy
    @WaqarAhmad-ch9hy 4 місяці тому +1

    Hello
    I need help to solve motor , safety censor and blower issue !!.

    • @alexxander7289
      @alexxander7289 Місяць тому

      are you sure ? remove sensor fuse and test for electrical continuity. better to order extras switches and sensors for the whole machine. Why ? its cheaper and quicker to remove sensor and replace with a know good sensor rather than wait for a technician to come out and do the same work. remember a sensor is just a switch. either normally open or normally closed.

    • @alexxander7289
      @alexxander7289 Місяць тому

      if sensor keeps blowing is it always on first cut ? or about how many cuts into the job ? 10, 20, 50 cuts ? If this is the case, im sorry to tell you that your motor is having a thermal over heating problem Before installing a new motor, have a licensed eletrician double check each leg of the eltricial feed. Is you cutter a 220 or 308 voltage ?

  • @hossinmdafjal
    @hossinmdafjal 27 днів тому

    এটা কোথায় ভাই

  • @rogersquickprintnorthampto4042
    @rogersquickprintnorthampto4042 11 місяців тому +2

    How not to cut paper

  • @Old__boy..AtheisT
    @Old__boy..AtheisT Рік тому

    Nice

  • @carlosmv9403
    @carlosmv9403 5 місяців тому

    0:19 0:25 0:30 0:31 0:31

  • @MdrofikulIslam-s9e
    @MdrofikulIslam-s9e Місяць тому

    ভাই আমার মোশিনের মাঝে মধ্যে সারভে নট রেডি দোখায়

  • @pintupaswan3674
    @pintupaswan3674 8 місяців тому

    Bhai setting kese karta hai

  • @sohagsarkar2869
    @sohagsarkar2869 4 місяці тому +1

    আমি করব চাকরি

  • @sonamdadul7556
    @sonamdadul7556 2 роки тому

    Price plz

  • @HanifKhan-co3ux
    @HanifKhan-co3ux 9 місяців тому

    Purv kitna sigall feiss

  • @hammerzeit6283
    @hammerzeit6283 2 роки тому +1

    Включи уже раздув стола

  • @NasirAnsari-zi6ve
    @NasirAnsari-zi6ve Рік тому

    it's on paper white

  • @MrEthanhines
    @MrEthanhines 5 місяців тому +1

    how not just show

  • @MDARIFULISLAM-gq4nx
    @MDARIFULISLAM-gq4nx 2 роки тому

    wow

  • @Alundrahs
    @Alundrahs Рік тому

    Man I miss printing. But this dude is slow af. He’d be fired

    • @MrQuirinus
      @MrQuirinus Рік тому

      Maybe he's not a professional.😂

    • @alexxander7289
      @alexxander7289 Місяць тому

      his boss needs to be. The machine was not even installed/setup correctly.

  • @rameshloganathan8711
    @rameshloganathan8711 Рік тому

    42"cutting machine price

  • @GeorgeKatik
    @GeorgeKatik Рік тому

    Please send me a power diagram

  • @pikespeter
    @pikespeter 3 місяці тому +2

    No need to slam the paper so hard against the backgauge

  • @marie.graphic1350
    @marie.graphic1350 Рік тому

    Bhai Programme machine ka naaam kachede me millatheya

  • @Rohancoolsmarty007
    @Rohancoolsmarty007 Рік тому

    I've Polar 1972