Stihl concrete saw TS 420 engine ASSEMBLY

Поділитися
Вставка
  • Опубліковано 23 січ 2025

КОМЕНТАРІ • 42

  • @bikedogtor1663
    @bikedogtor1663  4 роки тому +1

    The assembly was fun to do. I like how easy but genius these machines work and I learned a lot. Hope the video helps you!

  • @phyllismacevicius8821
    @phyllismacevicius8821 2 роки тому

    Thank you for sharing the TS 420 rebuild and assembly. I am doing this rebuild currently and your video is very helpful.

  • @JosueA-j3y
    @JosueA-j3y Рік тому

    Exelente colega muy buen trabajo

  • @sw-ed5sx
    @sw-ed5sx 4 роки тому

    You make it look easy. Great job!

  • @tysauce1986
    @tysauce1986 2 роки тому

    Do you know what the factory settings are for the H and L carb screws?

  • @tobysmith8032
    @tobysmith8032 2 роки тому

    Top tip... Remove the ears from the circlips, they tend to vibrate and either break off or the circlip works its way out! 👍

  • @ATLAS01COPCO
    @ATLAS01COPCO 4 роки тому

    Great cleaning job

  • @dalechalkey3729
    @dalechalkey3729 4 роки тому

    are the bearings on the crank shaft the same size? on my ts420, it looks like one of the bears is a 15mmx35mm by 11mm. the dealer sold me two of the same bear sizes but i think my unit is older and uses two different sizes.

    • @bikedogtor1663
      @bikedogtor1663  4 роки тому

      They aren't :-/ I ordered two of the same size and stopped bc one didn't fit.

    • @tjs.mw.
      @tjs.mw. 2 роки тому

      The one I did had 2 different sizes

    • @williamcawthorpe8910
      @williamcawthorpe8910 4 місяці тому

      After 2013 the bearings are 2 different sizes

  • @husky-cc6xq
    @husky-cc6xq Рік тому

    Servus Bikedoctor, why you document in english? I got a quotation from a Stihl dealer, but the price for zylinder is very, very high and am honast, the fixing of exhaust is a missconstrution. Do you know a a good dealer for Stihl parts? Thank you Toni

  • @NEW-HORIZONS
    @NEW-HORIZONS 2 роки тому

    Where can I buy accessories (cylinder and carburetor)

  • @jorgetrigueros1820
    @jorgetrigueros1820 4 роки тому

    Does crankshaft for 420 works on 480

  • @johnkosheluk1041
    @johnkosheluk1041 2 роки тому

    You don't do a psi and vac test on the crankcase what do you think will happen if you have a air leak especially on that aftermarket piston and cylinder

  • @funkhybrid
    @funkhybrid 4 роки тому

    Is there a reason why you don't use any lubricant or grease when you're re-assembling the main shaft and bearings? Seems like it would slide on a little easier. Enjoy your vids

    • @bikedogtor1663
      @bikedogtor1663  4 роки тому +2

      I never use lubricant on the outside of bearings bc if it goes bad the outer ring can slip in the housing and destroy it. You definitely do not want that to happen.

  • @pakolorente7423
    @pakolorente7423 3 роки тому

    Nice music - rebuild Aprilia bring me here. How many cc is in this engine saw?

    • @bikedogtor1663
      @bikedogtor1663  3 роки тому

      Thank you for your comment. I don't know to be honest.

  • @RicardoFlores-tq4wr
    @RicardoFlores-tq4wr Рік тому

    What is the company called and what is that piece called plz 2:31

  • @CarlosGarcia-xs6ig
    @CarlosGarcia-xs6ig 2 роки тому

    Buen bidio

  • @olavomartini674
    @olavomartini674 2 роки тому

    💪🏼👏🏼👍🏼

  • @felixmarquezZ
    @felixmarquezZ 2 роки тому

    Se le hecha aceite adentro donde va el piñón

  • @Jose50008
    @Jose50008 4 роки тому

    Great job is not easy.

  • @timazhanakpaev4753
    @timazhanakpaev4753 3 роки тому

    Чем моете?

  • @tjs.mw.
    @tjs.mw. 2 роки тому

    Alittle tricky but I did it