RCI LIVE - ***NEW*** FMS CESSNA 182 1500mm Unboxing, Assembly & Setup

Поділитися
Вставка
  • Опубліковано 13 тра 2024
  • Check it out at FMS► bit.ly/fmsC182rci
    Available NOW in Europe At TurbinesRC► bit.ly/TRCfmsC182rciRed bit.ly/TRCfmsC182rciBlu
    FMS CESSNA 182 at HobbyZone► www.hobbyzone.com/referral/rci...
    At FairRC► bit.ly/FairRCfmsC182rci
    Amazon Store► www.amazon.com/shop/rcinformer
    Benelux: www.beez2b.com/
    Australia: www.modelengines.com.au/
    Germany: www.d-power-modellbau.com/
    UK: www.cmldistribution.co.uk/
    NEW ERNST Plane stand links:
    Plane Stands► bit.ly/ernstRCrci2024
    💥SPECIAL LIMITED TIME FMS DISCOUNT CODES for RCINFORMER Viewers!💥
    ▼Use the links and apply codes▼
    💝FMS COUPON CODES for use at FMS💝
    💥SAVE 10% by using CODE► ReferralRCinformer OR $10 by using CODE► RCinformer💥
    ☢️5% OFF for new releases► FMS5NR☢️
    Check out SterlingKit models here:
    WS-15 Turbofan Engine kit:bit.ly/3tbeHrM
    V8 engine model:bit.ly/4aghnF5
    Christmas Sales:bit.ly/3NlC3S9
    USE Special discount code RCI14 to save 14%
    #stirlingkit
    Check out medievalbrick Here► bit.ly/mbCFMRCI
    Welcome to the RCINFORMER Field!
    Help us by clicking on our links below:
    www.rcinformer.com
    FMS► bit.ly/3w5J3dm
    Fair RC► bit.ly/3bMJrpP
    Horizon► alnk.to/28NJIyZ
    Hobby Zone Arrows► bit.ly/2XGEPa9
    Banggood► bit.ly/3dgAWhS
    Bitgo► bit.ly/2Ah40bf
    Amazon Store► www.amazon.com/shop/rcinformer
    RTLFasteners.com► TBD
    JP Hobby European site here► bit.ly/3JQthY4
    HET European Site here► bit.ly/3JL8iWe
    FLYING TIGER RC Plane storage system► bit.ly/36gXRMG
    ERNST MANUFACTRUING PLANE STANDS HERE: bit.ly/ErnstStandsALLRCI
    BuddyRC► bit.ly/3uUnj4m
    TurbinesRC *In France*► bit.ly/373frE3
    🌟The only glue I use for my RC MODELS🌟
    ZAP GLUE► amzn.to/3ClCfMe
    FOAM-TAC► amzn.to/3ClCfMe
    🌟SPEKTRUM NX10 & NX6 I use🌟
    NX10 & NX6► bit.ly/3fu2Iym
    🌟SPEKTRUM Smart Chargers & Checker I use🌟
    SPEKTRUM Smart charger Page► bit.ly/3V0OWUa
    🌟LiPo Packs I use🌟
    SPEKTRUM LiPo► bit.ly/3CiiLrY
    Roaringtop USA LiPo► bit.ly/3BU1JyQ
    CHINA HOBBY LINE LIPOS► bit.ly/3hWF0c0
    🌟AFTERBURNERS I USE🌟
    KM-RC Model UNIVERSAL AfterBurner here► bit.ly/3Pk1suW
    GOONIAC Afterburners► bit.ly/2I2FIWD
    5280RC TruFire Afterburners► bit.ly/3frYM0U
    🔽FMS Models🔽
    🌟TRAINER/CIVILIAN🌟
    Beaver► bit.ly/3E455lF
    EASY TRAINER► bit.ly/3RvRGpj
    J3 CUB► bit.ly/3E31eoZ
    Kingfisher► bit.ly/3fqKJsp
    PA-18► bit.ly/3y1jL0P
    SkyTrainer FMS► bit.ly/3BV7HPX
    SuperEZ► bit.ly/3fAyjhJ
    Ranger 1800/1200► bit.ly/3fznSuZ / bit.ly/3e2ID1s
    Ranger 850► bit.ly/3rkABEh
    🌟WARBIRDS & Parts🌟
    CJ6►bit.ly/3y3fIS2
    CORSAIR 1700M/1400/800► bit.ly/3Sqlk0J
    F7F►bit.ly/3y46LHP
    P-40 1400m►bit.ly/3SA3Yy6
    P-40 980m► bit.ly/3xZSwnl
    P-47► bit.ly/3y4uOGM
    P-51 1700M► bit.ly/3fxm6dJ
    P-51 1400► bit.ly/3LVrymD
    P-51 800► bit.ly/3rmaMnr
    PC-21► bit.ly/3fsUJS0
    T-28 YELLOW► bit.ly/3y3hGlo
    T-28 RED► bit.ly/3Sqn9e5
    TYPHOON 1100M► bit.ly/3LSwmsY
    Zero 1400/1100/800m► bit.ly/3E6aR6m
    🌟EDF JETS🌟
    A-10 70MM► bit.ly/3dV60tT
    AVANTI► bit.ly/3LYUNFu
    BAE HAWK► bit.ly/3fyGDP5
    F-15 ► bit.ly/3E40tvR
    F-16► bit.ly/3UOiHay / bit.ly/3SG9VcK
    F-18► bit.ly/3dSPGd6 / bit.ly/3SBrXNo
    F-35► bit.ly/3V2L3y2
    Futura V3► bit.ly/3rlM8mS
    Rafale 80M/64M► bit.ly/3LZv53p / bit.ly/3LU6wF8
    SCORPION 90MM► bit.ly/3SK1NYL
    VIPER 70► bit.ly/3BWN4Dc
    Yak 130 FMS► bit.ly/3SJmOTl
    🌟GLIDERS🌟
    ASW17/MOA/FOX 3M/2.3M► bit.ly/3BVOyO4
    RACERS/SPORT/AEROBATIC
    EDGE 540► bit.ly/3E6RpGk
    F3A Olympus► bit.ly/3SsBF4O
    F3A Explorer► bit.ly/3CnRJzk
    Flash 850► bit.ly/3y63qrW
    MXS ► bit.ly/3UPCVAO
    P-39► bit.ly/3RsP1wN
    P-51 RACERS► bit.ly/3fwoHES
    Pitts► bit.ly/3CovxVZ
    🌟HORIZON HOBBY MODELS & Their PARTS🌟
    ALL FMS MODELS► alnk.to/2jIv4b3
    A-10► alnk.to/ge2lzUT
    Air Tractor► alnk.to/90vhmvX
    Apprentice► alnk.to/aLERaGO
    CZ Cessna 150► alnk.to/3cigZEX
    Cirrus SR22T ► alnk.to/aWzC9EF
    Citation Longitude► alnk.to/btjT672
    Commander► alnk.to/8tL0qfU
    Draco ► alnk.to/7flHyz2
    F-15► alnk.to/bip8NHF
    F-16► alnk.to/c04aIZg
    F-18► alnk.to/fwnkljn
    F4U► alnk.to/6IBriwT
    Fw190► alnk.to/fwnklkm
    P-47► alnk.to/87Vv97Y
    P-51► alnk.to/1MYdPMd
    RV-7► alnk.to/3cihFyK
    Twin Otter► alnk.to/3cihFBu
    FB► / rcinformer
    INSTAGRAM► / rcinformer_official
    TWITTER► / rcinformero
    Website► www.RCINFORMER.COM
    #rcplane #rc #aviation
  • Наука та технологія

КОМЕНТАРІ • 32

  • @stevehelton3457
    @stevehelton3457 Місяць тому +1

    Just a side note....people sometimes order items based on your review. The dimensions you approximate for the wheels are inaccurate. There is no way the front wheel is that large. In fact, if you remove 3 screws you will find that it is actually a 2" wheel. A 2 1/4" (57mm) will not work. I know because I waited a week only to find out it was wrong.
    Dubro low bounce 2 1/2" works great with some modification, but no way the dimension for the front works.

    • @stevehelton3457
      @stevehelton3457 Місяць тому

      2 1/2" for the mains. Drexel the pants some and sand down the hub. I also used 2 small washers to center wheel in pants. Tighten all screws and very quiet!

    • @RCINFORMER
      @RCINFORMER  Місяць тому

      I indicated in the video that the nose wheel was approximately 1-7/8".... so I was about 1/8" off, just eyeballing it, when in fact it's really 2".... I indicated that the mains were 2-3/8" to 2-1/2" ...so I was about right on the money by eyeballing it.... I will usually go lower than higher when guesstimating so as not to mislead anyone... my guesstimate numbers were good:)

  • @richardwoods1739
    @richardwoods1739 2 дні тому +1

    Once the rx is installed under the floor you cannot see if you lose bind. To negate this I have placed the rx satellite on the passenger seat. This way you can check that all is OK just be looking at the orange light through the cabin window.

    • @RCINFORMER
      @RCINFORMER  2 дні тому

      @richardwoods1739 Good Idea!

  • @looneytunes47
    @looneytunes47 Місяць тому +2

    One area they messed up on was the flashing navigation lights are in the forward direction and the solid white lights are on the outter wing tips. so i plan on swapping the position of those 2 lights on each side

    • @azzir325
      @azzir325 Місяць тому +1

      Did you figure this out yet? I seem to have lost my flash capability. Not sure what I did but I did get the navs to stay on solid but can't seem to get the things that should flash to do so.

    • @looneytunes47
      @looneytunes47 Місяць тому +1

      @@azzir325 Jon from 2 brothers rc shows how to do it in one of his video,s

  • @fredrik-cm4kl
    @fredrik-cm4kl 13 днів тому +1

    I say hi from Sweden, great video, I follow your channel and like the hole content. Keep up the good work and take care 😀

  • @Elisrc.
    @Elisrc. Місяць тому +1

    I missed you man ,im glad to see you again❤👍

    • @RCINFORMER
      @RCINFORMER  Місяць тому +1

      Thanks for watching! Been busy at work and prepping the new field! Once we get everything set up, we will be doing more videos from there:)

    • @Elisrc.
      @Elisrc. Місяць тому

      @@RCINFORMER good to hear that👍👍

  • @SCRedneckRC_2024
    @SCRedneckRC_2024 Місяць тому +1

    Thanks for the video, I broke down and bought one even though I really couldn’t afford it yet. Also you gained a subscriber in me 👍

    • @RCINFORMER
      @RCINFORMER  Місяць тому +1

      Thanks for buying one thru my link!

  • @hmz6535
    @hmz6535 Місяць тому +3

    Nice to see finally somebody got this airplane scale proportions right'

    • @larryblanks6765
      @larryblanks6765 21 день тому

      They had them right when Top Flight built their 182 at the right dimensions, I know I have one!

  • @afb911
    @afb911 Місяць тому +2

    Lol, they finally found a use for all those VGA connectors since monitors went HDMI

    • @RCINFORMER
      @RCINFORMER  Місяць тому

      Yep! They are probably getting a deal on them.... but they work well:)

  • @Mikeylikesit1968
    @Mikeylikesit1968 Місяць тому +1

    To bad FMS can't get the stickers straight on the tail like the Cessna and Skylane

  • @azzir325
    @azzir325 Місяць тому

    Did you figure out the lights yet? I seem to have lost my flash capability. Not sure what I did but I did get the navs to stay on solid but can't seem to get the things that should flash to do so.

  • @leoyi3627
    @leoyi3627 Місяць тому

    Where u at??

  • @jeffreysmith5825
    @jeffreysmith5825 2 дні тому +1

    Can the tail be removed and put on a new fuse

    • @RCINFORMER
      @RCINFORMER  2 дні тому

      @@jeffreysmith5825 You should be able to do that as long as there was no damage done to the mounting area.... The tail simply removes with two screws

    • @jeffreysmith5825
      @jeffreysmith5825 2 дні тому +1

      I understand that the tail boom can be removed but dose the tail itself come out​@@RCINFORMER

    • @jeffreysmith5825
      @jeffreysmith5825 2 дні тому

      Not sure you answered me

    • @RCINFORMER
      @RCINFORMER  2 дні тому

      @@jeffreysmith5825 I'm not sure if I understand your question.... Each elevator half comes off and is connected with a spar... Also, the vertical stabilizer comes out as well

    • @RCINFORMER
      @RCINFORMER  2 дні тому

      @@jeffreysmith5825 None of the tail is glued on.... The vertical stabilizer does go on with a piece of double sided foam tape

  • @herberton112
    @herberton112 Місяць тому

    Uauuuuuu

  • @alaskanight940
    @alaskanight940 Місяць тому +1

    Echo makes listening hard 😢

    • @RCINFORMER
      @RCINFORMER  Місяць тому

      Sorry, we got rid of the echo at about 11min

  • @stevehelton3457
    @stevehelton3457 17 годин тому +1

    But what you indicated won't work. Just trying to help others to not waste money and order the wrong wheels.

    • @RCINFORMER
      @RCINFORMER  15 годин тому

      What did I indicate? My measurements were mostly correct. In fact, I slightly under estimated the size of the wheels so as to not give a falsely larger size. In the future, I will just remove the wheel pant to give a more exact size.... However, this is why I used a ruler in the video....