Just in case anyone does this - when you take out the main motor hub don’t get your fingers in the gap that opens as your doing this. There are extremely strong magnets that will “suck” it back in and trap your ur fingers with a lot of force
It is customary to have 3 liters of hard liquor when working on the later models of this scooter. You CANNOT disconnect the rear wheel as easily due to the brown yellow and blue cable being screwed, meaning now you have to remove the battery just to get enough room for a tool
Can a second external battery be connected to the front of the ninebot e45d? So I had one internal and two external batteries? how can i connect together ?
i don't speak german, but i understand, you can use any grease you like... i'm using this one because i have it at moment, u can use even wd40 for sliding the bearings and some silicon or lithium base grease for gasket
Hi super video👍 meine Frage woran hast du gemerkt das die lager im hinterrad kaputt sind? Meiner macht nimmlich Geräusche und fährt ganz schwer auf 6 kmh und das wars
RZ: The bearing side has a low friction seal lined with steel plate synthetic rubber (non-contact type); RS: The bearing side has a contact seal lined with synthetic rubber or polyurethane (contact type)
hello friend I got an important question, from minute 14:35 onwards, is it not necessary to apply sealant such as Hylomar to the edges of the cap so that dirt does not get into the housing? I read in a forum that you should definitely do this. Do I have to? :) Thx for making this video!
14:36 хорошо видно что с завода нанесён голубой герметик, (для гидроизаляции мотора) при разборе мотора вы его повредили! И при сборки не убрали заводской герметик и не нанесли новый! А при езде в дождь или снег - слякоть как раз на заднее мотор-колесо летит вся грязь и вода! Это же явный косяк при сборе мотора? Или я дурак просто.....
Где ты там увидел голубой герметик? Нету там герметика вообще. И основная причина воды в мотор, хреновые подшипники... А не крышка мотора. Я уже в 200 раз всем говорю, знаешь сколько моторов я уже перебрал? Не один мотор не был ржавый из-за крышки, только из-за того что подшипники оригинальнфе были дерьмовые.
Hi friend, thanks for the nice video! I need some support that I'm looking for a long time, hopefully you can help me. Do you know the correct code of each hall sensor inside the motor? I'm struggling to find it and I'm having problems to run my G30 due to that. It would be very very helpful. I almost could read it at 5'02" in 4k resolution...
@@RMFUNTIK Thank you very much for replying me, I'll give a try with the sensors in the link! But my concern still is that it seems that in the G30 motor, the central Hall Sensor is different than the other two. That means two types of hall sensor and my guess is that this is my problem now, I'm using the same Hall sensor in the all three positions...
Hi, my back tire is kind off jammed and the scooter died while i was riding it, but there was one cell battery left. What do you think is the issue ? Btw, nice video.
Weird part is, there was battery left ... And stopped and then the tire is locked ... Not completely but it move with more effort. And the scooter does not turn on either. Also, I put it on charge last night thinking that the battery was down, but it did not turn on while i put it on charge. I checked today morning and its still not turning on. So, if its motherboard then just replace it? I am in Canada... Do you have any recommendations?
Off topic but does anyone know how to remove the yellow stripes from the rims ? I have tried a heat gun and also acetone but they seem to be painted / stuck on pretty good ? id like to jiust have the matt black rims with no colour ...
Just in case anyone does this - when you take out the main motor hub don’t get your fingers in the gap that opens as your doing this. There are extremely strong magnets that will “suck” it back in and trap your ur fingers with a lot of force
just had this happen to me, be careful lmao
@@vfxcristi4noha! I had to get my wife to pry it open. Crazy force in there!
It is customary to have 3 liters of hard liquor when working on the later models of this scooter. You CANNOT disconnect the rear wheel as easily due to the brown yellow and blue cable being screwed, meaning now you have to remove the battery just to get enough room for a tool
It's getting harder and harder to fix something...
Фунтик ты красавец!
Great tutorial. Question - is it necessary to you use lithium grease?
nop.. you can use any other grease for rubber bushings
awesome. watched this video in advance before i need to change one day
Glad it was helpful!
have you needed to change?
@@truthseeker6804 got hit by a car and the tire is always deflating so I might have to soon
@@phylosophersstoned43 what? sorry about that. hope you are ok?
Can you remove the shaft from the motor?
With a press, I guess yes.
What about the radial seals? Are there replacements available?
don't know, but you don't need to replace them, they are in good condition and you can grease them inside + the bearings have a good seal.
My scooter do not run over that 17 miles. What do you think is wrong with it.? I replaced the trouble speed already
needs diagnosis
Would these bearing work the the Segway f30?
And is the WD-40 lithium grease okay to use?
don't know f30, never been in my repair shop
@@Thevariablegamer wd40 is not lithium grease..
No wd40 makes lithium grease
Would it be fine to use it?
Can a second external battery be connected to the front of the ninebot e45d? So I had one internal and two external batteries? how can i connect together ?
Yes if you can do a custom firmware to unlock charging while driving.
Hello
Could you please tell me the size of the torx screws of the bottom plate that give access to battery, motherboard etc please? Thanks
i don't remember, a guess t10 with a hole. just buy your self a cheap set.. they cost like 5 dollars.
👍 juste le joint d'étanchéité à la pâte entre les 2 parti qui n'a pas été fait..
the is no seal in original.
witch quit of tools needed for the bearing operation? ty
all shown in the video.
Great video! Was the scooter going like it was breaking or what was it that told you it was the bearings?
client wanted to change them just for maintenance :) they where fine, but you know, scooter was had 4000km on it.
чувачек если не наживил то так болты не закручивают может выйти осечка а солидола не жалеешь опыт слабенький но молодец что собрал
если у тебя руки кривые, то да, возможно! молодец, что посмотрел как делают профи!
Если одел перчатки то это не знак профи а проблемка
Hello friend, do you know what are the measurements of the front wheel bearings of the Segway f40e scooter? Thanks 👍
sorry no, take it apart and read whats on bearing written, there should be a numer 6001/6002 or 6003 rs
What type of diameter bearings should use for ninebot g30 or max g30 ?
front rs6001 rear rs6003
hey my back tire somehow blocked and it’s not start now, kind jammed, its rotate but stucking… do you think this is the same problem
i guess it's electronics.
Thank you very much for this video
you are welcome!
Hi! Super Anleitung!
Frage: Was ist denn das für ein rotes Fett, was du da reinschmierst? Irgendwas spezielles, oder einfach nur "Fett"?
i don't speak german, but i understand, you can use any grease you like... i'm using this one because i have it at moment, u can use even wd40 for sliding the bearings and some silicon or lithium base grease for gasket
Etwas spät aber im Deutschen: Lithiumseifenfett
какой нужен подшипник на самокат digma allroad max
сними крышку, там будет написано на нем.
@@RMFUNTIK ясно спасибо
Hi super video👍 meine Frage woran hast du gemerkt das die lager im hinterrad kaputt sind? Meiner macht nimmlich Geräusche und fährt ganz schwer auf 6 kmh und das wars
well, the scooter was about to hit 2000km, so i did change them, they where normal, but i decide to change them, because front bearings was kaput.
@@RMFUNTIK OK danke für die Info 👍
@@selcukkonar1301 bitte schön
Ich hab es so ähnlich nach dem Lagerwechsel macht meiner Geräusche und kommt nur auf 10kmh und weiß nicht woran es liegt. Was war es bei dir?
Oder hat jemand ne Idee was ich falsch gemacht habe
Thanks
your Welcome
I want to so this nyself. Is it diffucult to make the bearing press?
you can hammer it, find a socket with the same diamentr as the outer ring of the bearing..
nop.. just some socket heads and threaded steel pin
RS v RZ BEARINGS does it make a difference? One on my scooter which is a copy of this have 6202RZ bearings
RZ: The bearing side has a low friction seal lined with steel plate synthetic rubber (non-contact type); RS: The bearing side has a contact seal lined with synthetic rubber or polyurethane (contact type)
@@RMFUNTIK I have brought ZZ bearings to replace the RZ as the RZ Dont appear to be widely available as the RS/ RZ ...hopefully they will last
RZ bearings are not sealed (water, dust proof)..
Hau meni km is on dis motor?
1000
А герметиком разве не нужно наносить на крышку аккумулятора,когда обратно ставишь?
зависит, от того будешь ли ты ездить в мокрую погоду или нет, у самоката рейтинг Ip54. + там штатная прослойка хорошая.
@@RMFUNTIK No it's not IP 54 I think it's much better!
А можно ли достать-купить оригинальное 9 мотор колесо (более скоростное) и поставить за место 6 , и прошить что он ехал под 40 км в час?
незнаю
hello friend I got an important question, from minute 14:35 onwards, is it not necessary to apply sealant such as Hylomar to the edges of the cap so that dirt does not get into the housing? I read in a forum that you should definitely do this. Do I have to? :)
Thx for making this video!
yes you can put some sealant it won't be bad :) but the main water and dirt leak is from bad bearing seal
А почему именно литиевую смазку использовали?
ты можешь просто wd смазать.. разницы нет.. я просто набил ее туда, чтобы вода не проникала.
@@RMFUNTIK понял, спасибо
@@RMFUNTIK а подшипники оба 6003?
@@pixelfullhd зад да.
14:36 хорошо видно что с завода нанесён голубой герметик, (для гидроизаляции мотора) при разборе мотора вы его повредили! И при сборки не убрали заводской герметик и не нанесли новый! А при езде в дождь или снег - слякоть как раз на заднее мотор-колесо летит вся грязь и вода! Это же явный косяк при сборе мотора? Или я дурак просто.....
Где ты там увидел голубой герметик? Нету там герметика вообще. И основная причина воды в мотор, хреновые подшипники... А не крышка мотора. Я уже в 200 раз всем говорю, знаешь сколько моторов я уже перебрал? Не один мотор не был ржавый из-за крышки, только из-за того что подшипники оригинальнфе были дерьмовые.
кто знает где заказать крышку моторколеса? и желательно с гравировкой 250ватт или менее, ну вы поняли))
ua-cam.com/video/4SN1Ma0Posw/v-deo.html
отдельно вроде как не продается.
Скажите а такой самокат как на видео с 6м моторколесом вы прошиваете? И сколько из него можно выжать км в час?
если не заблокирован, то да.
xiaodash 36км на ровной а если горка то под 45
❤️🤝
By a New Wheel with Motor its Easier !!!!!
This is way cheaper
A bearing costs only a couple euros
a lot more expensive lol
Hi friend, thanks for the nice video! I need some support that I'm looking for a long time, hopefully you can help me. Do you know the correct code of each hall sensor inside the motor? I'm struggling to find it and I'm having problems to run my G30 due to that. It would be very very helpful. I almost could read it at 5'02" in 4k resolution...
www.falconpev.com.sg/collections/spare-parts/products/motor-hall-sensor-single-piece try here
@@RMFUNTIK Thank you very much for replying me, I'll give a try with the sensors in the link! But my concern still is that it seems that in the G30 motor, the central Hall Sensor is different than the other two. That means two types of hall sensor and my guess is that this is my problem now, I'm using the same Hall sensor in the all three positions...
@@adriancovi www.scooterhacking.org/forum/viewtopic.php?t=174
Hi, my back tire is kind off jammed and the scooter died while i was riding it, but there was one cell battery left. What do you think is the issue ? Btw, nice video.
what do you mean by off jammed?
Like it rotates but with some thing like its in gear.... ? Or stuck to it .
@@anshulkhatri6231 hmmm... maybe something wrong with your motherboard? never seen that trouble with g30..
Weird part is, there was battery left ... And stopped and then the tire is locked ... Not completely but it move with more effort. And the scooter does not turn on either. Also, I put it on charge last night thinking that the battery was down, but it did not turn on while i put it on charge. I checked today morning and its still not turning on. So, if its motherboard then just replace it? I am in Canada... Do you have any recommendations?
@@anshulkhatri6231 nope it not motherboard, guess it's BMS, check the voltage on the battery pack it should be 37-42v
Excelente
🎉mega Kugellager 10mm oder 6mma
Off topic but does anyone know how to remove the yellow stripes from the rims ? I have tried a heat gun and also acetone but they seem to be painted / stuck on pretty good ? id like to jiust have the matt black rims with no colour ...
they are painted..
Super
Thank you
What kind of tool is used to remove the bottom plate?
t25
каким номером вы откручивали винты на колесе?
torx? 25 или 27
@@RMFUNTIK
да torx 25 или 27 уточните пожалуйста номер
купи набор..
@@RMFUNTIK Torx 20
собрал без герметика . это косяк..
как было в оригинале, так и собрал.
@@RMFUNTIK так-то оно так но лучше ставить на герметик чтобы ничего не ржавело
а оно и не будет ржаветь.. вода протекает через подшипники, но тут два сальника еще стоят.. так что если ты его не кинешь в реку, ничего не будет.
Seller for wheel caps?
Продавец для колёс?
Congrats you managed to put the tire direction the wrong way
No they didn't
Those wheel bearings are trash