How This Solar Panel And Setup Power This Entire Building With Appliances After Installation.

Поділитися
Вставка
  • Опубліковано 27 вер 2024
  • How This Solar Panel And Setup Power This Entire Building With Appliances After Installation.

КОМЕНТАРІ • 17

  • @Anikruza
    @Anikruza 4 місяці тому +2

    I love this guy explanations when am ready i will inform Edo cbc

  • @nelsoncollins5549
    @nelsoncollins5549 4 місяці тому +1

    nice one

  • @realToby
    @realToby 4 місяці тому

    Mucus? 😅My brother meant gunk/residue. Good Job 👍

  • @LexionKing
    @LexionKing 3 місяці тому

    Charge Controllers aren't sized with Amps alone. There is a maximum Expected PV Power input (Current x Voltage) for each Charge Controller, hence dictating the number and wattage of Total Panels it can work with. Also 24 hours Light guarantee is quite subjective and depends on a lot of factors. Its not a given, especially in Rainy seasons like this, or Geographical Location and Total hours of good sunlight, and also the availability or non availability of Grid Power to augment. It also depends on how deep you want to drain the batteries to guarantee a Longer service Life especially as what we have in this setup are not Lithium Iron Batteries. So, if not carefully planned, you might be using 24 hours light for the whole system to pack up in 6 months and the product quality is erroneously Blamed.

  • @ampofoboadi
    @ampofoboadi 4 місяці тому

    Oga, but why is the AC system excluded? Any problem with it and AC systems?

  • @aiwanfosupremejustice1379
    @aiwanfosupremejustice1379 4 місяці тому +1

    14 solar panels? How many watts each of the panel?

    • @charledawn
      @charledawn 4 місяці тому +1

      400 watts 60 amps charge controller

    • @GTdontDOthat
      @GTdontDOthat 4 місяці тому

      t​his is not d answer

    • @GTdontDOthat
      @GTdontDOthat 4 місяці тому

      55 amp times 48volt is 2640watt then divide 2640watt with the number of the panel to know how many watt each is producing

    • @oladejiajuwon3076
      @oladejiajuwon3076 4 місяці тому

      Exact same question in my head

    • @GTdontDOthat
      @GTdontDOthat 4 місяці тому

      @@oladejiajuwon3076 read my reply

  • @taiwoayomide5341
    @taiwoayomide5341 3 місяці тому

    Don't you thinking the charge controller is too small

    • @LexionKing
      @LexionKing 3 місяці тому

      The higher the Battery Bank Voltage or inverter voltage, the lower the current draw required to power loads and the cheaper the gauge of wires required. Although i worry for the Maximum Power Input of the Charge controller especially with 14 Panels. They must definitely be low wattage panels else he has a system here that can burst into flames when the rainy season is over and we have longer hours of hot sunlight

    • @taiwoayomide5341
      @taiwoayomide5341 3 місяці тому

      @@LexionKing I don't agree with you 100 percent less wire gauge kee for tubular battery 8 PCs?????

    • @LexionKing
      @LexionKing 3 місяці тому

      @@taiwoayomide5341 Absolutely depends on whether they are in series, or Parallel. This is why the higher the operating Voltage of your inverter, the lower the current required and lighter the wires you can actually use for your components (Not Talking of the post inverter AC connections side). Do your research. Not like the system is going to draw the entire battery bank amperage in one go anyways.

    • @taiwoayomide5341
      @taiwoayomide5341 3 місяці тому

      @@LexionKing you should have mention these earlier that why most solar hybrid inv with high PV capacity will work fine with small gauge cable since all the panel are connected in parallel