Audi Q7 Air Suspension Calibration/Adaptation

After trying to do calibration on this car , we found out that the vehicle has some DTC in the fault memory ( 34 - Level Control ) .The fault was : 00776 Level Control System Sensor; Front Left (G78) . We needed to fix the problem , before continuing the calibration process .
Support the channel : / crankauto
Shop coordinates ( for business inquiries ) : / crankauto
CRANK

[@LeTRANSPORTEUR69]

*hello my Audi Q7 is very raised on the right side and crushed on the left side I can not calibrate it it always remains in the air I have so much value that I do not know what to enter do you have any idea how can we put it back to the factory?*

[@kalinvenkov9920]

Apparently, the right sensor doesn't accept the stability and is stuck, I had the same problems and none of the knowledgeable masters know anything, I fixed it myself. Disassemble the sensor and see if the upper part is blocked, if it is blocked in the apple, try to move it

[@marinkassakov9062]

Чудесно видео ! Би било прекрасно ако го направите и на български. Не че няма да се оправим и на английски но , по ми се искаше да е на роден език. Благодаря!

[@papa_arekapc4070]

Nice tutorial, thx 😊

[@bussmils]

You must check and bars on the tayres same.

[@iga7314]

Is there a way to find out the exact problem with the Air suspension in Audi Q7 2010

[@javiervidal7645]

Ostia ojalá estuviese traducido llevo 1 año peleando con la suspensión neumatica de mi touareg y no hay forma

[@thaUnit100]

Just followed the same sequence but channel 5 says error.. what to do next ?!

[@cocomonkey19k]

I've got the same issue. Only fault code is control postion not learned

[@samp6162]

You need to exit from VCDS. Load up the software again, go to level control, security access, unlock with 31564. Then go to adaptation and configure your settings. If you make a change and go back, then back into adaptation, you'll get the error you describe. 😊

[@bobbyakawaycooljr5914]

How did you get the security code

[@jakubluszczak2748]

Hi is suspension on LIFT mode when you measuring?

[@samp6162]

Automatic

[@sarmadalqaysi2199]

Hi thanks for this info, question, I have audi a7 2013 and it has the driver side highest then passenger side, how I can fix it please?

[@betimsulejmani6205]

Thank you,god bless you

[@Jose.G_BJJ-MMA]

Security acces code engine module 01 For Q7 4L 3.0 tdi (BUG) 2006?

[@samp6162]

31564

[@kaibintech]

Great video!

[@damianos17xyz99]

Is this fsi or tdi ??

[@vladleonard86]

Hy there.. i have a 2008 Q7 4L LHD and i have a problem. I left the car on offroad mode and the next day i found it with the rear up (still on offroad) and the front down with the driver side even lower than the pax side (unbalanced). I started the car..started to raise up automatical and it drove fine... At night i left it in dynamic mode.. the next morning again the same isue..the rear was ok at the setting i left the car, but the front again with the same problem. The front lower than the rear and the driver side even lower!

[@crank3646]

Hi VLL !
Without a scan tool , is going to be impossible to tell you what is the problem

[@fernandoct6]

Hi.. could you fixed it?

[@vladleonard86]

@@crank3646 it doesen't give any error on vcds

[@nezarmaamar9489]

Hello, also have the same problem, did you find out why?

[@andreipreluca5329]

Gerat 💪💪

[@phisigpsitriton]

TY for posting

[@PVflying]

Is the security code the same for all cars, or how would I find the right code for my car? It's an A6 Allroad C6

[@v12mercedes-benz72]

MrCurry 31564

[@Guille8888]

hello. the procedure is the same, with an Allroad 4F?

[@crank3646]

If i remember right , yes

[@mendez77054ify]

Will this be the same steps for one one wheel is higher than rest? I get no codes but top right is higher then left one. All others are good.

[@rfclowry]

mendez77054ify mine back passenger side is the same ? Did you fix your problem ?

[@86channel86]

Did you fix the problem?

[@Daymox]

Русский?)

[@JT-482]

100 пудов