You are my new hero! You helped a completely non-fix it girl, fix her staple gun. Thank you!
This lady thank you.
I just had my JT-21M unjammed and works like new.. cheers mate from downunder😀
Just undo the nut and bolt in the rear and the staple carrier comes out the bottom.
good video. yeah its the same here. if it don't work, take it apart and see why. throwing things away is to easy.
Just fixed mine that kept shooting 2 staples out. It had two problems, epoxy glue got stuck between the striker and the front cover, forced the striker away from cover and then it hit 2 staples. Other was the staple carrier, it has 2 pieces spot welded together and it broke apart. I carefully epoxied it back together. Long ago, I was gluing some FG cloth and the glue was not fully cured, so glue got stuck between the cover you took off, and the striker. It had been broke for more than 10 years.
I made the mistake of letting parts go flying everywhere and now I have a brand new, almost completely disassembled stapler on my hands.....
Would you know why my T50 handle will not press down on the staples? I took the front cover off and cant get it work right. Thanks for your help.
That's a symptom of a jammed staple somewhere binding it up. Sorry I can't be any more help.
I didn't even know they go bad! I've been using the same staple gun for fourteen years and never had one problem. But yeah I'd probably tinker with it
This one in the video is pretty old and that was the only problem I've had with it. It's stapled more targets than I can count. Thanks man!
Try using pliers to put. the E clips on - just squeeze them on
Realy good,,but show me how the trigger is made.
Hi can i ask if They have a stapple reloader of guntacker in the store cause my guntacker pushing reloader is gone
Do you maybe have an advice what to do if your staple gun shoots 1-3 clips? Sometimes one 2 come out and 1 holds perfect and the other is upside down? I have no explanation for that....
Wow, that sounds strange. Could be the spring or flawed staples. I'd try a new lot of staples and go from there. Other than that, I'm not sure what else it could be. Good luck!
@@Bluelightbandit Just fixed mine that did that. Two problems, epoxy glue got stuck between the striker and the front cover, forced the striker to hit 2 staples. Other was the staple carrier, it has 2 pieces spot welded together and it broke apart. I carefully epoxied it back together. Another problem could be wrong width staples.
I did exactly what you did and after i assembling the leaver is not
Moving loose up and fix back same problem. Don't know what to do now.
Without looking at it, it's hard to tell. Sounds like the handle isn't seated properly. Sorry for your troubles.
Mine works as it should except it will not drive 1/4 inch staples completely into pine wood.
Video me kich dikh hi ni rha
I still haven't received my contest prize yet ☹
Not going to lie bud. I would probably still throw it away even while knowing how tp fix it. I dont have any of those clips. If i had to go to the hardware store to buy those clips then I would just go ahead and buy another gun.
Thumbs down. You failed to proceed with the rest. After removing the two e clips you conviently left out some crucial information about how it would fall apart.
Just for giggles, I went back and watched the part where I removed the clips and pins. I literally mentioned being careful not to let parts fly out. Maybe paying attention and being mechanically inclined just isn't your thing. But thanks for the 👎😊
Here's some free crucial information for you also. Retaining clips and pins (ironically) "retain" parts from moving freely. Therefore when you remove said "Retaining hardware", expect parts to be free. You're welcome 😊
Yeah I’m 15 so I watch your channel for this reason to I also have a target stand and use it to put my targets up and have a few that don’t work
That's awesome man, thank you so much!
i guess it's kind of off topic but does anybody know of a good site to stream newly released series online?