Windscreen Washer Pump Replacement - Peugeot 307

How to remove and replace the windscreen washer pump on a 2001 to 2008 Peugeot 307. The washer pump on this car had been changed to a different type of pump than the normal one for this car but the process is very similar. The normal part for this car is a Febi Bilstein 24633 or equivalent. Thanks for watching. Please comment, like and subscribe !.
~~~~ Part Links ~~~~
As an Amazon Associate I earn from qualifying purchases.
🚗 Washer Pump ~ amzn.to/3OqlGS8
Disclaimer: Screwsnutsandbolts is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to www.amazon.co.uk
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2022
Read important information below:
Disclaimer
Under no circumstances will Screwsnutsandbolts be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Screwsnutsandbolts or a third party. In no event shall Screwsnutsandbolts be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against improper use or unauthorized modifications of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Screwsnutsandbolts recommends safe practices when performing any do it yourself repairs and or with tools seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.

[@pilgrimoutdoors-uk6177]

Absolutely spot on. Step by step and to the point. Brilliant, I'm on this in the next few days as the fuse is still intact but there is no noise coming from the pump at all. Cheers.

[@pilgrimoutdoors-uk6177]

Just completed it - works a treat, The hole in the bottle was a touch to big for the grommet, and there was a tiny leak, but a bit of plumbers sealing tape sorted it ... Not all great news though..on jacking the car up i noticed a snapped Suspension spring...so it's off to the garage. Cheers!

[@screwsnutsandbolts]

@@pilgrimoutdoors-uk6177 Good job, pity about the spring but it's better that you know about it now I suppose :)

[@pilgrimoutdoors-uk6177]

@@screwsnutsandbolts All fixed now.

[@screwsnutsandbolts]

@@pilgrimoutdoors-uk6177 Well done :)

[@andyshannahan]

Cheers, superb guidance video on this. Clear, to the point and easy to see what's needed. Exactly the same as this to do a 206.

[@screwsnutsandbolts]

You're welcome!

[@josecarlosmontalvolorenzo1168]

Thanks 👍👍👍

[@screwsnutsandbolts]

No problem 👍

[@Passengervehicles]

Good vid

[@screwsnutsandbolts]

Thanks :)

[@langbuntho]

I like your video

[@screwsnutsandbolts]

Thanks !

[@lexilol5673]

This is super helpful. I actually need to change the wash tank, not the pump. Does anyone know how it’s attached and how it can be removed? Only video I can find is for a 206

[@screwsnutsandbolts]

I don't have a video but here's the instructions from the manual which may help:
Washer Fluid Reservoir:
1 The washer reservoir is located behind the
right-hand front wing and supplies both the
windscreen and tailgate washers via the same
pump. On models equipped with headlight
washers, the reservoir also supplies the
headlight washer jets via an additional pump.
2 Working in the engine compartment,
remove the plastic cover from above the
washer fluid reservoir. The cover is secured
by two expanding plastic rivets. Push the
centre pins In a little, then prise the complete
rivets from place (see illustration).
3 Slacken the right-hand front roadwheel
bolts. Jack up the front of the vehicle, and
support it securely on axle stands (see
Jacking and vehicle support). Remove the
right-hand roadwheel.
4 Remove the front right-hand wheel arch
liner. The liner is secured by several
expanding plastic rivets. Push the centre pins
a little, then prise the complete rivets from
place, and manoeuvre the front section of the
liner out from underneath the wing.
5 Pull the reservoir filler neck upwards from
the reservoir.
6 Note the correct fitted location of the
washer hoses (if necessary, mark them for
identification purposes) then disconnect the
hoses from the washer pump(s).
7 Disconnect the wiring connector(s) from the
washer pump(s) (see illustration).
8 Slacken and remove the retaining nut then
move the reservoir to the rear, and free it from
the body. Manoeuvre it out from underneath
the wing (see illustrations).
9 Refitting is the reverse of removal, ensuring
that the hoses are securely reconnected. Refill
the reservoir and check for leaks.

[@stevanilic8725]

Super👍👍👍😇

[@screwsnutsandbolts]

Thank you !

[@bordonbert]

You DO NOT remove the "retaining clip" from that plug on the pump as you did with your screwdriver. You simply push the wire clip inwards with your finger and the plug then pulls off the socket without any real effort at all. That way you can keep on using the plug for the rest of the life of the car!!!

[@screwsnutsandbolts]

Thanks for the tip 👍

[@georgemarcos8688]

Thanks
Wanted to ask you about something please
One of my friends has water leaking under the winshield, just in the VIN number area.
Noting that he didn't replace the winshield recently
Where do you think the leakage is coming from?

[@screwsnutsandbolts]

Where exactly is the VIN number, is that below the windscreen on the drivers side ?. Where is the water ending up ?. Test the windscreen washer with the bonnet open and see if any of the washer hoses are disconnected or leaking in that area

[@georgemarcos8688]

@@screwsnutsandbolts I have a photo I just can't attach it

[@georgemarcos8688]

@@screwsnutsandbolts but yes the windscreen on the driver side . VIN is the chassis serial number in some recent model it is under the windscreen and can be seen from outside

[@screwsnutsandbolts]

@@georgemarcos8688 So where exactly is the water ending up ?

[@georgemarcos8688]

@@screwsnutsandbolts the VIN in in a deep area and the water is ending up in this area

[@syidi_]

is it the same position on peugeot 306? need information, thank you..

[@screwsnutsandbolts]

It is probably very similar but I'm not 100% sure

[@goxyeagle8446]

Remove all that just to access little pump 🤦🏻‍♂️

[@screwsnutsandbolts]

Yes it's a lot !