hello, i have 8970 and i have a different problem, when i put front reserve i have the gear 5' when i put it to back automatical going to 2 gear how i can calibrate that?
Hi! Thanks for the video, very useful. Please if you can help me with another video or explenation, how to see the fault codes on the small screen (right down), since I only see the book and I have a problem with the tractor. I know that I need to enter in factory mode and swith from off to on (to see the fault codes), yet I cannot find to way how to enter in this mode. Thanks a lot!
Do you have any videos of cleaning the solenoids on the side of the transmission? Tried to calibrate our 8870 but it wouldn’t work the dealer said try cleaning the solenoids first then calibrate.
just watched this and I found out early on that the lever needs let loose early on or it wont go into flashing CC. There is a difference in adjusting the upshift and downshift between the 16 and 18. I have the 18 in an 8870. bought a Buhler CD which had some extra stuff in it .
hello dear, we have a g210 tractor that doesn't start, normally it changes gears but can't move, what could be the problem.. please tell us because you help us a lot
If it cranks but doesn’t start, then it could be the fuel shut off solenoid. If it will not crank at all, it could be a bad relay, fuse or battery cable.
Hello I have intention to buy a new Holland g 170 But the tractor have a problem, he didn't shift just until the 10 speed What do you think it's electrica problem or something inside the gearbox Thanks for answer
I would be careful. I have heard that it’s $20,000 to rebuild the gearbox. Does the display show it shifting through the gears? What are the error codes? Maybe have a look at the calibrating the transmission on a genesis tractor video I made. That video will show you how to see if the clutches are wore out. If they are wore out I would stay away.
Hi! My G240 in F1 stops to 23 , F2 stops to 29 and R to 99 . When i check the hole calibration holding R to the left it shows F1 23 , F2 29 and R 50... When i drive the tractor shifts normally to 9 gear , when put 10 gear it jumps ? any ideas?
Almost all of these tractors shift hard from 9-10, and 10 to 9. This is especially true if you have the 18 speed Funk transmission. Other than calibration I don’t have any other advise.
To 9 to 10 shift quality improves isn't there advice even shown in the book in this video?? "Calibration of shift constant" In neutral, lever to left, key on, change the digits and so on..
F330- Transmission reverse circuit open. The solenoid is 2nd to the bottom on the right side of the shifting solenoid block F333- Fuel shut off solenoid error. This is the solenoid that shuts off the tractor on the right side of the engine above the injector pump. common problem. F410- Exhaust temp sensor. This is right on top of the engine connected to the exhaust. F16- Left draft pin failure. check the plug for dirt or corrosion on the three point.
Hey Cirtojanu George! Thanks for watching and commenting on the video! I believe that it is the American model of basically the same size of tractor. Thanks for checking the videos of our organic Wisconsin dairy farm!
Thanks for your help very much We from Iraq do not have any way to communicate with you can you send this file(catalog)to me that I need to him so much thank you very much for this help I hope you to success, and the best
Thanks for the help! Made it easy to follow along! Made my 8970 shift way better!
Thanks for commenting! Glad to help A Farmers Life!
Thanks for posting this. Came in handy for me today 👍
I’m glad it was helpful for you.
Thank you just followed the vid in the 8870 and gtg! Again thank you!
Glad you liked our videos and thank you for checking out our channel! We really appreciate your support!
Thanks for the video. 👍
Thank you
Glad we could help
Thanks for the video. Could you tell me what section that is in the operating manual? I have a digital version and I can't find it in there. Thank you
hello, i have 8970 and i have a different problem, when i put front reserve i have the gear 5' when i put it to back automatical going to 2 gear how i can calibrate that?
Hi! Thanks for the video, very useful. Please if you can help me with another video or explenation, how to see the fault codes on the small screen (right down), since I only see the book and I have a problem with the tractor. I know that I need to enter in factory mode and swith from off to on (to see the fault codes), yet I cannot find to way how to enter in this mode.
Thanks a lot!
Do you have any videos of cleaning the solenoids on the side of the transmission? Tried to calibrate our 8870 but it wouldn’t work the dealer said try cleaning the solenoids first then calibrate.
just watched this and I found out early on that the lever needs let loose early on or it wont go into flashing CC. There is a difference in adjusting the upshift and downshift between the 16 and 18. I have the 18 in an 8870. bought a Buhler CD which had some extra stuff in it .
Thanks Tim. I always see your good comments on the Genesis Facebook page as well.
It does not show me the CC when i push the shifter to the left what should i do?
I'll be trying this tomorrow. Hopefully it works
Thanks for watching and commenting Lobbyrobby! We appreciate your comment. Have a great day and hope this works!
Thanks! This video helped me a lot! The translation in the French notice must be faulty! I couldn't enter in the CC mode on my g170!
Glad to help! Thanks for watching and commenting!
what is the title of the book you are using?
Answer, please
New Holland 8670,8770,8870,8970 repair manual.
hello dear, we have a g210 tractor that doesn't start, normally it changes gears but can't move, what could be the problem.. please tell us because you help us a lot
If it cranks but doesn’t start, then it could be the fuel shut off solenoid. If it will not crank at all, it could be a bad relay, fuse or battery cable.
Hello I have intention to buy a new Holland g 170
But the tractor have a problem, he didn't shift just until the 10 speed
What do you think it's electrica problem or something inside the gearbox
Thanks for answer
I would be careful. I have heard that it’s $20,000 to rebuild the gearbox. Does the display show it shifting through the gears? What are the error codes? Maybe have a look at the calibrating the transmission on a genesis tractor video I made. That video will show you how to see if the clutches are wore out. If they are wore out I would stay away.
How repair fail only in forward first speed suddenly, I hope help.thanks
There’s a speed censor under the transmission, that could be your problem
hello ,you can help me ,i have a new holland tm150,and it show p32 fault code,and the ranges not change ,it just in B, please
If someone knows the answer to this question, please respond in the comments. Thank you!
Hi! My G240 in F1 stops to 23 , F2 stops to 29 and R to 99 . When i check the hole calibration holding R to the left it shows F1 23 , F2 29 and R 50... When i drive the tractor shifts normally to 9 gear , when put 10 gear it jumps ? any ideas?
Almost all of these tractors shift hard from 9-10, and 10 to 9. This is especially true if you have the 18 speed Funk transmission. Other than calibration I don’t have any other advise.
To 9 to 10 shift quality improves isn't there advice even shown in the book in this video??
"Calibration of shift constant"
In neutral, lever to left, key on, change the digits and so on..
Is there an online service manual available anywhere?
Not that I know of. I had to buy one.
I have a New Holland G240 tractor code F 418, F018, F024.
gear shifting is not smooth forward all gears and back
Can you send the catalog that you have?
Sorry. I am not able to do that. I was able to find an electronic copy online that I printed off.
I have a New Holland G190 Tractor code F330
F333
F410
F16
F330- Transmission reverse circuit open. The solenoid is 2nd to the bottom on the right side of the shifting solenoid block
F333- Fuel shut off solenoid error. This is the solenoid that shuts off the tractor on the right side of the engine above the injector pump. common problem.
F410- Exhaust temp sensor. This is right on top of the engine connected to the exhaust.
F16- Left draft pin failure. check the plug for dirt or corrosion on the three point.
serie 8?
yes it should work for 8670 8770 8870 and 8970.
8870??
Hey Cirtojanu George! Thanks for watching and commenting on the video! I believe that it is the American model of basically the same size of tractor. Thanks for checking the videos of our organic Wisconsin dairy farm!
Thanks for your help very much
We from Iraq do not have any way to communicate with you can you send this file(catalog)to me that I need to him so much thank you very much for this help I hope you to success, and the best
Glad this video helped! Have a great day!
@@farmcards can you send this catalog to me, please
?
It worked for us.