Wheel bearing replacement on site without dismantling the hub carrier
Вставка
- Опубліковано 14 гру 2017
- How to change a wheel bearing directly on the vehicle, without a press and without dismantling the hub carrier. All stages: hub removal with a slide hammer puller, extraction of the bearing, new bearing refitting, hub refitting with a wheel bearing tool set.
This video does not constitute or replace a real specialized technical manual, and was only made for convenience and educational purposes. "TutoBuild Eng" makes no warranties of any kind and accepts no liability. "TutoBuild Eng" cannot be held responsible for any damage caused to devices or persons using information contained in this video. The use of the information contained in this video is at your own risk. - Авто та транспорт
Thanks a lot, great voice and assembly manner.
Thanks for taking the time to do a useful video. Need to do mine before too long.
Good Video!! Nice work!
Very thorough for the views you have and quite easy to follow...congrats!
i dont mean to be so off topic but does anybody know of a trick to log back into an Instagram account..?
I was dumb lost the password. I would love any tricks you can offer me
@Colt Emory instablaster :)
@Langston Nash Thanks for your reply. I found the site through google and I'm trying it out now.
I see it takes quite some time so I will reply here later when my account password hopefully is recovered.
@Langston Nash it did the trick and I now got access to my account again. Im so happy!
Thanks so much, you saved my ass !
@Colt Emory No problem :D
Easy to follow 👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼
perfect job except the brake rotor should have been cleaned of grease an oil prior to installing the brake pads. nice job and video
Great video, I’m proud of you that everything got torqued with a torque wrench except the lug nuts, hope you just didn’t show it, lug nuts are as important as the the brake bolts, also I’d clean up the brakes and re-lubricate them but either way good job thanks
😂😂😂 never in my life I've used torque wrench for nothing on my cars, and it's was totally fine all these years.
I like it !
Súper Good work 100%👍
Excellent
nice..
I love it
Nice
HOW TO CLEAN CSRPET
Would have spun the new assembly round a couple of times before refitting the wheel. You might have done this but it was not shown on the clip.
Also, you sure about the torque on the shaft nut...?
It does seem overly tight ......
Just do it TIGHT it can never hurt. Ive never crushed a bearing brace ever using a bar. Just be sensible when applying pressure.Like remembering roughly how tight it was or count the turns by making a mark.
Good
Looks like it was a little bit easier than if you take it off the car.
11:41 What if the circlips don't have holes on the end points for gripping?
2 years later oof
Why did you put the bearing ih the freezer?
The OD of the bearing will contract just a fraction by freezing it. Easing installation within the bore of the knuckle.
Thanks.
Anyone who's doing this, remember to save your wrist !!!
Bro... could you please tell me... where this bearing removing set is available...i want to buy one. Or tell me its availability in India... thanks
It's a generic tool set sold under many brand names. You should have no problem finding one in India.
Animal con patas!!!!!!!!!!
who sale wheel bearing tool set
Look like that cheap autozone duralast brand wheel bearing lol
LESSON NO.1 USE a mans jack! Get car higher then in this video. Then you can tighten or loosen with out having to return the rachet or spanner. just go round like a clock hand.
If that mattered, why wouldn't he just use a short wrench after the bolt was loosened?
you don't grease a press in bearing
Way too much work🙄
He's not greasing the bearing. He's greasing the surface that the bearing shell slides into to make the task slightly easier.
A 9:25 you are install one of the clips. If you do that. Then how is the bearing able to go in
He's installing the rear/inside bearing C Clip.... Bearing stops at that clip and you know when u can't push bearing any further. It sort of can be used as a stopper also other than what its for safety
Hmmmm.....Do you really have a air compressor and air tools with you in the car at all times? "On site" is a bit off, isn't it?
Most people don't have any of these tools at hand, and have to go to a garage to get this done. Useful video, but only if you have the tools!
That gps voice is so annoying
lol at that point you are 3 bolts away from removing the hub, and do it by pressing much easier and faster and can do it inside
خیلی کاره اشتباهی کردی,نباید ضربه بزنی,😂😂😂👎👎👎👎