Це відео не доступне.
Перепрошуємо.
Replace polaris 500 ranger camshaft the fastest and easiest way.
- Додати в
- Мій плейлист
- Переглянути пізніше
- Поділитися
Поділитися
Вставка
Розмір відео:
- Опубліковано 21 січ 2024
- Edited by VideoGuru:videoguru.page...
КОМЕНТАРІ • 10
Наступне
Автоматичне відтворення
Polaris Sportsman 500 backfires! How to inspect the camshaft and check for a Lean condition.Titaniumman Garage
Переглядів 4,1 тис.
Polaris Ranger 500 Replacing all fluidsPolarisNuts Garage
Переглядів 38 тис.
Do Longer Camshaft Splits Affect Performance? | Engine MastersMotorTrend Channel
Переглядів 175 тис.
Буданов про плани на Курську область, та Воронеж #shorts #курск #воронежАпостроф TV
Переглядів 2,2 млн
«Путін почав це, надеріть йому зад»: американські сенатори про операцію ЗСУ в Курській областіРадіо Свобода Україна
Переглядів 646 тис.
Яшин - интервью после тюрьмы / вДудьвДудь
Переглядів 7 млн
КУДА ДАЛЬШЕ ДВИНУТСЯ ВСУ? БЕСЕДА С ЮРИЙ ФЕДОРОВФЕЙГИН LIVE
Переглядів 528 тис.
Polaris Ranger 500, How To Rebuild Carburetor, Carb, Will Not Idle, Start, Will Not Run, Acceleratecrankitt
Переглядів 3,9 тис.
Polaris Ranger 500 Top End RebuildJWS Repair Service LLC
Переглядів 16 тис.
903 Cu in Hemi Nightmare! 🤬Steve Morris Engines
Переглядів 211 тис.
Breaking Down How The CP4 Pump is a DISASTER & How To Avoid It With The DCR Upgrade!Dave's Auto Center
Переглядів 103 тис.
How the 2011 Ford Power Stroke Beat GM’s Duramax | Banks Speed SchoolBanks Power
Переглядів 444 тис.
Polaris 500 camshaft removal and replacementTitaniumman Garage
Переглядів 57 тис.
Polaris Ranger 800 - Camshaft Balancer Gear RemovalMid Nebraska Motorsports
Переглядів 2,9 тис.
2008 Polaris Ranger 500 engine assembly and install.Heavy Shoulders
Переглядів 4,6 тис.
1996 Polaris Sportsman 500 Cam & Rockers InstallationOld Jalopy Garage
Переглядів 11 тис.
Советы на всё лето 4 @postworkllcИстория одного вокалиста
Переглядів 5 млн
SCHOOLBOY. Последняя часть🤓⚡️КАН АНДРЕЙ⚡️
Переглядів 10 млн
🔥 Уся правда про українську СУДЖУЗе Інтерв'юер
Переглядів 163 тис.
😭ЛЮДИ ВОВКАМИ СТАЮТЬ....5 канал
Переглядів 2,8 млн
Яшин - интервью после тюрьмы / вДудьвДудь
Переглядів 7 млн
Знищені колони та десятки полонених: останнє про Курський прорив. Донбас, удари, бої | Свобода LiveРадіо Свобода
Переглядів 405 тис.
ПОДІЇ НА КУРЩИНІ: ЕКСКЛЮЗИВНИЙ РЕПОРТАЖ НАТАЛІ НАГОРНОЇ З СУДЖІТСН Тиждень
Переглядів 214 тис.
«Синку, ти не переживай. Сюди вона не впаде, вони всі повз летять»: військовий про перші дні війниСуспільне Запоріжжя
Переглядів 357 тис.
i actually watched this as because i was trying to make sure where the compression release spring was supposed to be. i had also figured the same position as you did, so you confirmed my thinking. The old one had slipped during removal, and the new cam had slipped out too far also. Thanks ford the video.
Great video bud! I don’t even have one of these engines but was thinking of buying a ranger needing an engine rebuild so thought would check out this video. You’re excellent at describing everything that needs doing. Cheers!
In my opinion, from watching many Repair videos, you did a great job explaining and showing the important details. I would encourage you to keep the Videos coming. I will definitely bookmark this for my upcoming camshaft replacement on my 500.
seems like the timeing chain is just stretched a bit that's why the timing sprocket is rotated backwards a degree or two with tension on the chain.
Can the camshaft cause knocking in the engine?
Good job
Hey I have a 99 ranger 6x6. Just replaced the clutch. Noticed it kinda seems like it boggs at a certain speed. The cams look good and shiny but the exhaust rocker has minor pitting, could that be the issue?
@tonyknightstep1927 the way to know if the cam is worn is to measure the lift. Basically the diameter of the cam lobe from 12:00-6:00 (highest measurement) and 3:00-9:00 (lowest measurement) to determine the actual lobe lift.
It's also very possible you have a carburetor issue.
@@paulkelley86 thanks man. Yea with the cams looking good(minus a actual measurement) and the rocker I thought maybe carb issue.
ah, confusing timing marks.. reminds me of the old 2UZ cam sprockets