ATTENTION: 15:30 For our Mech-EVO signals and Quadrix signals, the connection used should be Black to Red and Yellow to Brown. This method should be used on both the base models and the SE models.
When I connect black to red and yellow to brown using the Mech-Evo universal LED turn signals, I lost function of my front turn signals and the dash no longer shows my signals running. the Mech-Evos are flashing dimly as well. Is there a fix to this or did I just mess up somehow? (SE model)
So I’m trying to finish up installing this on the same bike you are using in this video. If i don’t have the SE model, where do I end up connecting the the black connection for the wires?
Love the product, great work guys, look forward to more from ya! ...Small problem I've run into with installation on Ninja 500 SE. (LED Tail light works beautifully). BL6 Sequential; having issues. Using the plug converters for SE, with everything hooked up, when activated, the dash shows no indication of either turn signal flashing, nor does the LEDs flash. If I disconnect a black or yellow wire from either signal on either side, the dash will show a rapid flash of the designated signal, but the signal itself does not flash. I believe the Ninja 500 SE comes with LED turn signal stock, so a LED relay wouldn't be necessary. Any advice would be greatly appreciated!
I got the sequential light for my ninja 500 40th se edition. I tried following the video however my turn signals are not working. Verified the fuses are okay using the old signals, front signals seem to be working. Do I need the relay to be able to make this work? Made sure everything is connected properly
I am having the same exact issue with my zx6r 40th anniversary, The turn signals work when 12v is applied. However they will not work when wired to the bike, and I made sure to check that the bike is supplying adequate power
I ordered the sequential turn signals and the sequential mode only works with the hazards and not for regular left and right turn signals. When I put my left and right turn signal it blinks rapidly with only two bulbs lighting up
@@angelalvarado7739 this sounds like your flash rate is too fast and the sequence does not have enough time to complete in each blink. Please watch carefully the part of the video that talks about signaling relay.
@@dylanpettit8445 email our Support Team and they can run you through some troubleshooting techniques. If all of your fuses are good and you have the signals wired in correctly, and the flasher relay installed, everything should work as intended.
I bought quadrix sequential light smoke for my ninja 500, i installed it, it works great, but only flash, like normal light, not sequential, any idea why？ Also video says connect brown wire to black wire yellow wire to red wire 15:38, the light doesn't work so i connect yellow wire to blue wire, light works. Plz help me
I got the smoked BL6 Universal LED Pod Turn Signals with the converters and when I plugged them in they aren’t working (not lighting up at all) , is there something I’m missing or not doing right?
@@KKchappell No worries at all. When you switch to LED signals from the stock signals you will more than likely experience some signal issues. Whether that be a hyperflash or no flash/constant on. Installing our LED Flasher Relay will correct and control your signal circuit regardless of the signal type and only one relay is needed for your entire bike.
can you guys please do the front led turn signal replacements for the z500? i know the z500 and ninja are the same for almost everything except for the front
@@TSTindustries a lot of people would really love that. even thought theyre essentially the same bike a handful of things definitely differ. also is there an estimated time for the integrated tail light to be out by chance?
What doesn’t work? The methodology should be the same except for the different connectors. If you’re using our Quadrix-D lights, you will need to splice into your tail light circuit to achieve the running and brake light functions and then connect the signal wires (green wires on our lights) normally with the appropriate connectors. If you’re having issues, please reach out to our Support Team and they may be able to provide guidance.
ATTENTION: 15:30 For our Mech-EVO signals and Quadrix signals, the connection used should be Black to Red and Yellow to Brown. This method should be used on both the base models and the SE models.
When I connect black to red and yellow to brown using the Mech-Evo universal LED turn signals, I lost function of my front turn signals and the dash no longer shows my signals running. the Mech-Evos are flashing dimly as well. Is there a fix to this or did I just mess up somehow?
(SE model)
@@Uhlijuh please tell me what other modifications you have done to this bike.
@@Uhlijuh did you install our LED Flasher Relay?
@@TSTindustries ah no flasher relay installed, I’ll install that to hopefully fix the issue
Successful, thank you much 🙏🏽
cant wait for the integrated option to come out
So I’m trying to finish up installing this on the same bike you are using in this video. If i don’t have the SE model, where do I end up connecting the the black connection for the wires?
I'm not entirely sure I understand. If you email our Support Team and include photos, they should be able to help out. Support@TSTIndustries.com
Love the product, great work guys, look forward to more from ya! ...Small problem I've run into with installation on Ninja 500 SE. (LED Tail light works beautifully). BL6 Sequential; having issues. Using the plug converters for SE, with everything hooked up, when activated, the dash shows no indication of either turn signal flashing, nor does the LEDs flash. If I disconnect a black or yellow wire from either signal on either side, the dash will show a rapid flash of the designated signal, but the signal itself does not flash. I believe the Ninja 500 SE comes with LED turn signal stock, so a LED relay wouldn't be necessary. Any advice would be greatly appreciated!
@@TabyKat a relay may still be necessary due to the difference in current draw from the stock LEDs to ours.
I got the sequential light for my ninja 500 40th se edition. I tried following the video however my turn signals are not working. Verified the fuses are okay using the old signals, front signals seem to be working. Do I need the relay to be able to make this work? Made sure everything is connected properly
When you say they aren’t working, do you mean they aren’t flashing at all?
@@TSTindustries yes, the dash was not flashing the arrows either if that helps
I am having the same exact issue with my zx6r 40th anniversary,
The turn signals work when 12v is applied. However they will not work when wired to the bike, and I made sure to check that the bike is supplying adequate power
@@6ohTreez do you have our LED Flasher Relay installed?
@@TSTindustries I just found about about it after further research, just ordered it.
Thank you!
Do we need to disconnect the battery before changing the oem lights for the tst ones?
@@kaimanahana6972 no, but you should work with the bike shut off.
Yall were fast too come out with these! Purchasing now.
I ordered the sequential turn signals and the sequential mode only works with the hazards and not for regular left and right turn signals. When I put my left and right turn signal it blinks rapidly with only two bulbs lighting up
@@angelalvarado7739 this sounds like your flash rate is too fast and the sequence does not have enough time to complete in each blink. Please watch carefully the part of the video that talks about signaling relay.
Can we get a new integrated break light soon? Been wiring to upgrade for my new 500 to get rid of the little turn signals
The soonest we may possibly release an integrated tail light would be next year.
If i get the adjustable option, can I still use the turn signals with a close out?
Absolutely!
i bought the relay flasher , connectors , and everything i needed but my turn signals aren’t even lighting up on the dash. idk what to do
@@dylanpettit8445 it sounds like you may have a blown fuse.
@@TSTindustries where are they at lol
@@TSTindustries i found the fuses , all are good . any other idea as to why it isn’t working ?
@@dylanpettit8445 email our Support Team and they can run you through some troubleshooting techniques. If all of your fuses are good and you have the signals wired in correctly, and the flasher relay installed, everything should work as intended.
When’s the integrated one coming out
@@joshmann5393 hopefully sometime next year.
I bought quadrix sequential light smoke for my ninja 500, i installed it, it works great, but only flash, like normal light, not sequential, any idea why？ Also video says connect brown wire to black wire yellow wire to red wire 15:38, the light doesn't work so i connect yellow wire to blue wire, light works. Plz help me
@@rudytian8554 brown to yellow and red to black should get you going. The breakdown in this video was for our BL6 signals.
I got the smoked BL6 Universal LED Pod Turn Signals with the converters and when I plugged them in they aren’t working (not lighting up at all) , is there something I’m missing or not doing right?
They won’t turn on unless activated when plugged in on the rear. Did you purchase and install our LED Flasher Relay?
@@TSTindustries I didn’t, I must’ve missed that part in the video lol. That’s on me
@@KKchappell No worries at all. When you switch to LED signals from the stock signals you will more than likely experience some signal issues. Whether that be a hyperflash or no flash/constant on. Installing our LED Flasher Relay will correct and control your signal circuit regardless of the signal type and only one relay is needed for your entire bike.
can you guys please do the front led turn signal replacements for the z500? i know the z500 and ninja are the same for almost everything except for the front
If we’re able to get a Z500 in-house, we may be able to knock that out.
@@TSTindustries a lot of people would really love that. even thought theyre essentially the same bike a handful of things definitely differ. also is there an estimated time for the integrated tail light to be out by chance?
@@kaplandg Not at this time. We're in the very early stages of R&D so we would imagine it could be potentially a year before our light is ready.
@@TSTindustries thank you for the insight!
Yippee!!! Thanks so much for uploading this! 🙏🏽 Amazing video brake down
Thanks for the view and the feedback!
Does not work for SE KRT Edition I bought a tail tidy and sequential D lights. Tryna find a video but no updates.
What doesn’t work? The methodology should be the same except for the different connectors. If you’re using our Quadrix-D lights, you will need to splice into your tail light circuit to achieve the running and brake light functions and then connect the signal wires (green wires on our lights) normally with the appropriate connectors. If you’re having issues, please reach out to our Support Team and they may be able to provide guidance.
no option or the ABS version on your website :(
Having ABS or not will have no effect on the install process. The bike used in this video is an ABS model.
@@TSTindustries awesome thanks!!!
DO YOU HAVE SOMETIMES LIKE THIS FOR A Z 1000 SX 2015 MODEL. PLS SHARE
@@GhostRider-ms1ep NOT AT THIS TIME.