in my experience, baking soda corrodes the plates. i suggest using sodium hydroxide. if you can't get your hands on any sodium hydroxide, i put out a video on my Channel on converting baking soda into sodium hydroxide. it's pretty easy to do with electrolysis.
It would last longer if the spade terminals were not exposed to salt water. Salt water will attack all the connections and the exposed copper wire in the spade terminals. Would be best to completely cover all electrical connections inside the container with RTV.
use graphite rods as electrodes. Use high voltage and don't mix anything in water. you are producing toxic gases by adding salt. A single bridge rectifier will work great with graphie electrodes at higher voltages producing HHO.
hey, if you light the gas, will the generator blow up? If so, should I make another hole for the gas output and make another bubbler so H2 and O2 can be separated? bad english sorry
How could you put main leeds + and - in electrolytic liquid, I think that contacts should be outside and inside bottle shoud be only plates on charge, you're loosing voltage unnecessarily ,you are watching on resistance but not on this, also more plates (area) more efficiency less current, but it works somehow, i like DIY, keep doing things.
There are very small energy loss. From the cell connector is firmly fastened bolt, which is quite thick. In addition it is a single cell to 2V instead of 4 cells to 12V. Therefore, my method of joining in no way interferes and does not cause additional loss because the screws also act as small cell :)
I don't think it matters as long as the bolts and wires are made of the same metal. If they were different metals they would work as poles and likely start to charge the electrolyte whilst rapidly degrading . Similar to if you put a copper pcb under water and apply a voltage, the copper migrates within minutes and forms that greeny brown crap. Yes, very technical of me I know XD
Mad-E for me None of the students of Budweiser Pothead teachers even understand your question. Though it almost answered itself when you mentioned "resistance" and "more plates" almost meaning closer plates of increased contact. Having little to no electronics instruction myself, it is generally accepted current travels path of least resistance of whatever materials, not always shortest path. So current, conducted through a medium pool of identical fluid, does not travel the first potential circuit terminals separated longer distance apart being more insulated in comparison, until greater potential circuit beyond of plates closer together wear into corrosion, tarnish, etcetera become comparably greater insulated by increased resistance of impedance. That is why & how answering your question. Your question does holds foresight concerning longer equipment product warranty.
that's how you make stingers to heat up water if you don't have a stove or microwave, and that's all this is doing is boiling the water. I built stingers back in the early 90's. it's cool that you are learning this stuff.
+Louis Fischer yeah, well, you can clearly see the water is heating up, or I should say generating electricity "current", but that's basically exact same way you make stingers, but you don't put it inside of a container and seal it off, I'm talking about the way you take 2 pieces of steel and put a spacer in between the 2 pieces of steel, which we used popsicle sticks as spacers and then we used dental floss to tie it together, and that's how we used to heat up water, or you could make donuts out of toilet paper and use an empty milk carton container, then hang it from dental floss and light the donuts on fire. Then you just make sure that the carton is full of some kind of liquid, that way the carton won't burn, you could even use an empty plastic peanut butter jar, which won't melt as long as it has liquid in it.
Again, there is no heat involved in this process! the electric current passing through the H2O solution, from one set of metal plates to the other, causes the h2o molecules to break down into hydrogen and oxygen. what you see bubbling isnt from the solution "boiling". Its the hydrogen and oxygen moleules sepparating and rising. There is no heat in this process lol! You can stick your fingers into the jar of water without injury from heat. You should read up a bit on your chem/physics ;)
I have a couple questions. I saw the balloon fill presumably with hydrogen. where was the oxygen displaced to? what clearance between the pates did you use?I have a 13.6vdc 19 amp power supply. would that voltage be too strong? do you have any recommendations as to how to store the gases for later use? since salt can be used as a dielectric this could possibly be used as an underwater self contained breathing apparatus.
the oxygen and hydrogen were mixed in the balloon because both the anode and cathode plates were together. Its generally safer to keep the hydrogen separate when storing (its less combustible). Honestly you could store it in 2 liter soda bottles if you are careful enough (do at your own risk) although that would be very difficult for something to go wrong. The optimal voltage gap between each plate is about 2 volts. Your 13,6vdc would produce a lot of excess heat because of the high voltage. Use neutral plates to lower the voltage and increase efficiency (Im sure you can find a plethora of things on the internet on how to use them. Although you should use about 5 between positive and negative plates). It could be used as a breathing apparatus if enough energy were present. Submarines sometimes use this tactic to continually have a safe supply of oxygen. Then again these subs usually have nuclear reactors on board and have huge amounts of energy at their disposal.
It is better to spend your money on a tune up. On a well tuned engine, adding a mixture of hydrogen, oxygen and water to the intake does nothing useful.
Great! But what about adding a bubbler(to be safe because hydrogen is flammable) and sanding the plates b4 putting them together? (sanding=more surface area= more surface area where reaction can happen :p)
Very nice and clear video, im just wondering where does the oxygen go? how can it be improved so that the oxygen can be extracted separately? Thanks for the video
The oxygen leaves the electrolyzer mixed with hydrogen, making brown’s gas. This is called a single output cell, whereas a split output would have two separate electrodes that have an isolated output, but still have electricity flowing through them.
Salt only allows current to flow . HHO is the end product, no matter what you use the electrolyte . The only difference is the efficiency of the generator , the electrodes wear and the minimum voltage of the water splitting
But the clorine in salt will get relised with the hydrogen while the sodium and oxygen bind and stay in the water. But either way atleast the hydrogen will still get relised.
You're right :) I had to check it , actually part of the oxygen will react and will be in the water. But the most important gas generator (hydrogen) will be evolved without a problem :)
+M.N. Projects Please do not use pure salt as electrolyte, since the chlorine gases that are produced with it are highly toxicy. Youre better off using regular baking soda.
how did you build the core tho? video?? or guide anywhere? and wont the plastic melt after it heats up? why not use mason jars and why salt and not pure baking soda?
This is cool.. but what is it used for? I'm trying to find ways to make a home generator for in case of power outage. I guess I'd like to start with the strength of something that can power my grow lights if the weather outside is unreliable and cold, but have no power indoors like nuclear winter.. but if I can make something that could also run fridge etc that wouldn't hurt. Any suggestions? Thanks either way and God bless !!
first of all, i like your work very much cause you concern for the little details,, but as i learned years ago, this operation produces oxygen and hydrogen, which are mixed in your balloon am i right?
nice attempt, and except salt as electrolyte, that gives chlorine, it is cool. you used 2V and 10A surprising as most use 12V dc supply. I am surprised to see Earth kind of thing, that connection I did not understand though (yellow wire), All the Best for more such experiments.
Is the Output Energy stored in gas about the same as the input, or is it more because a lot of energy comes from the hydrogen in the water or something like that
The generator is powered by voltage of 2V , little more than the minimum voltage distribution of water. Neutral electrodes are used when you want to power the generator a higher voltage. Then we obtain as if several generators connected in series. Between the two electrodes voltage should be about 2V :)
7 plates total, 5 neutrals. For 12/14v systems : 2 volts per cell, no heat is made, your energy makes MORE GAS! Seal them to, from each other. No high voltage leakage.
If you are in a warm climate you can generate hho by simply filling your gen. & putting it in the sun,there is enough electricity in the air for modest production for free,no joke Phil
No there's not. Every chemical reaction CAN happen spontaneously on a small scale given enough potential occurrences to overcome the statistical unlikeness, but H2O is by FAR the more chemically stable state compared to H2 + O2, and in a mixed environment of H20 + H2 + O2, the spontaneous reactions will trend towards more water. The trivial amount (I'm talking single digit count of molecules,) of H2 + O2 that form off of water would be imperceptible to anything but the most technologically advanced testing devices, IF even then. Why do you think we don't have H2 in the atmosphere even though 70% of the surface of earth is water?
Cool :) How about using aluminum foil? Does it work? and clothes pins holding wires onto them and plastic bottle caps cut like washers And how much amperage can 2 volts carry? (voltage is a path to current)
was gud. could u post some video to show how efficiently u can harness the gas produced. and by this exp what could be the output by harnessing the gas produced
I would just like to know where one gets a 2V 10A battery. Speaking of, 10A is HUGE!!! In the range of a gulf cart battery, and they go for about $200 USD. Great video until he tossed in a wrench. Make a video using AA, AAA, C, D, 9V, or 12V. That is what we have in America. Then again, maybe I should do one using off the shelf American parts. Look for a relavent video on this subject on my chanel in the near future. As much as car makers dance around electric technology, Hydrogen is where we are going because 250 unit apartment building in NYC can't charge batteries with solar panels.
just have your two separate electrodes far apart. You can do this in an open tub of water, the hydrogen will form at the cathode (positive terminal) and the oxygen at the anode (negative terminal) if you put an upside-down container above the bubbling cathode you should start collecting hydrogen because it is less dense than air.
+SupremeStigma it shouldn't matter as long as the resistance of the water isn't too much. You pretty much just want them far enough apart that the containers you are collecting the gases in don't collect a bit of the other gas. If you don't want the gas collected to be contaminated by air, fill the container you're collecting in with the water, turn it upside-down while submerged, and lift it slightly above the water above the electrode, so that the closed end of your container is above water, but still full of water because of suction. You can then keep it in place with a clamp or something like that.
is 19.5V, 3.3A and 65W (Laptop charger Output)enough for electrolysis? If yes how much HHO production can i expect? Pls answer it'll MEAN and HELP a LOT.
je réponds je suis français de souches et je peux te dire que ce que ses personnes disent est faut et je t expliques pourquoi ce sont les frères mongolfier qui ont inventé les premier au monde l utilisation de l air chaud par l invention de la mongolfiére il y à de cela plus de deux cent ans dans le passé et ils ont fait voler la première mongolfiére au monde devant louis 16 bien avant la révolution française et oui les français sont les premier au monde à avoir voler dans les airs qui dit mieux d après toi ?
john pages, Ils parlaient des zeppelins (ballons dirigeables allemands), pas de la montgolfière. Et tu dis être français de souche, certes, mais l'anglais faudrait le travailler un peu, tu comprendrais mieux "ce que ses personnes disent"...
You should replace salt with sodium hidroxide (NaOH) or anithing else, because if you use salt (NaCl) in electrolisis, you obtain chlorine (Cl2) wich is very flammable and toxic instead of hidrogen (H2)
Lets look at the cost as you used a soldering gun, drill, drill press, screw driver, pliers,heat gun,silicone,and somehow I think the total cost is above 5 bucks. Having copper wire immersed with your Stainless steel means your wire will disintegrate far faster than the stainless. Proof of concept yes , cheap no.
Run a generator on this and fuel vapour so not to overheat the head. Easily done, but then Governments could not blame us for global warming and tax us for it!
Hi, using salt (NaCl) isn't the best idea. You would create hydrogen yes, but clore gas too. Just as little info clore gas was used as chemical weapon in WW1 and it could hardly demage your engine, also NaOH the new salt formedin the bottle must be trated carefully. Hight concentrations can you make blind.
hi it's me Mr creature i'm really sorry for your dissapointed.. and i'm here for retract and it will not be repeated ? i'm waiting for you good response thanks...
I dont think so. Hydrogen Tourches need much more gas than this generator can produce :) You would have to do several of these generators and connect them
Ich konnte nicht genau erkennen, was das Ziel sein sollte. Aber jene Anordnung ist nicht zu empfehlen, denn die zersetzt Wasser und Salz (NaCl ?) in gefährliche Komponenten: Chlor, Wasserstoff und Sauerstoff. Der Luftballon ist am Ende also keinefalls nur mit Wasserstoff gefüllt !! Wenn man da eine Flamme dranhält, kann es heftig knallen! Und auch schon bei der Elektrolyse kann das Ding explodieren. Hier sollte also noch mal nachgebessert werden.
now what are you going to run this to? your car? how about a lawnmower with a small generator on it to power the cell once its running and recharge a small battery?? ;)
+M.N. Projects It's a great video. you should add an annotation telling people to use one of those if they can, or otherwise be careful with normal table salt as it produces chlorine gas instead of oxygen.
not for long due to the high corrosion rate of aluminum, hence the need for stainless or better instead of copper which also corrodes super fast in electrolosis. gold, silver or platinum are all ideal with platinum showing the most corrosion resistance.
I never knew that about salt creating a toxic gas good thing to remember to use baking soda.
eastkyphotos
eastkyphotos it produces chlorine gad
eastkyphotos no, Use NaOH or KOHn no CO2 gas then
J Stuyfzand whats this? links??
in my experience, baking soda corrodes the plates. i suggest using sodium hydroxide. if you can't get your hands on any sodium hydroxide, i put out a video on my Channel on converting baking soda into sodium hydroxide. it's pretty easy to do with electrolysis.
You little genius. You truly have a gift. Run with it. God Bless You Always.
It would last longer if the spade terminals were not exposed to salt water. Salt water will attack all the connections and the exposed copper wire in the spade terminals. Would be best to completely cover all electrical connections inside the container with RTV.
use graphite rods as electrodes. Use high voltage and don't mix anything in water. you are producing toxic gases by adding salt.
A single bridge rectifier will work great with graphie electrodes at higher voltages producing HHO.
You need to mix something in the water or it won't work. You do need baking soda instead of salt.
graphite will be a good electrode
hey, if you light the gas, will the generator blow up? If so, should I make another hole for the gas output and make another bubbler so H2 and O2 can be separated? bad english sorry
One question: Why drill holes in the corners you will cut off? I thought you might use those drilled, cut-off corners for something, but you didn’t.
How could you put main leeds + and - in electrolytic liquid, I think that contacts should be outside and inside bottle shoud be only plates on charge, you're loosing voltage unnecessarily ,you are watching on resistance but not on this, also more plates (area) more efficiency less current, but it works somehow, i like DIY, keep doing things.
There are very small energy loss. From the cell connector is firmly fastened bolt, which is quite thick. In addition it is a single cell to 2V instead of 4 cells to 12V. Therefore, my method of joining in no way interferes and does not cause additional loss because the screws also act as small cell :)
I don't think it matters as long as the bolts and wires are made of the same metal. If they were different metals they would work as poles and likely start to charge the electrolyte whilst rapidly degrading . Similar to if you put a copper pcb under water and apply a voltage, the copper migrates within minutes and forms that greeny brown crap. Yes, very technical of me I know XD
Mad-E for me
Mad-E for me None of the students of Budweiser Pothead teachers even understand your question. Though it almost answered itself when you mentioned "resistance" and "more plates" almost meaning closer plates of increased contact.
Having little to no electronics instruction myself, it is generally accepted current travels path of least resistance of whatever materials, not always shortest path.
So current, conducted through a medium pool of identical fluid, does not travel the first potential circuit terminals separated longer distance apart being more insulated in comparison, until greater potential circuit beyond of plates closer together wear into corrosion, tarnish, etcetera become comparably greater insulated by increased resistance of impedance. That is why & how answering your question.
Your question does holds foresight concerning longer equipment product warranty.
2:09 is that copper i need help plz
that's how you make stingers to heat up water if you don't have a stove or microwave, and that's all this is doing is boiling the water. I built stingers back in the early 90's. it's cool that you are learning this stuff.
Nothing is boiling there. Water is split into hydrogen and Oxygen. Close to no heat at all.
+Louis Fischer yeah, well, you can clearly see the water is heating up, or I should say generating electricity "current", but that's basically exact same way you make stingers, but you don't put it inside of a container and seal it off, I'm talking about the way you take 2 pieces of steel and put a spacer in between the 2 pieces of steel, which we used popsicle sticks as spacers and then we used dental floss to tie it together, and that's how we used to heat up water, or you could make donuts out of toilet paper and use an empty milk carton container, then hang it from dental floss and light the donuts on fire. Then you just make sure that the carton is full of some kind of liquid, that way the carton won't burn, you could even use an empty plastic peanut butter jar, which won't melt as long as it has liquid in it.
Again, there is no heat involved in this process! the electric current passing through the H2O solution, from one set of metal plates to the other, causes the h2o molecules to break down into hydrogen and oxygen. what you see bubbling isnt from the solution "boiling". Its the hydrogen and oxygen moleules sepparating and rising. There is no heat in this process lol! You can stick your fingers into the jar of water without injury from heat. You should read up a bit on your chem/physics ;)
stingers use a completely different principle - theyre basically a radiator. this is completely different
so you are trying to tell me that these things you are making don't generate no heat whatsoever?
How long do the electrodes last? (I think that's what they would be called)
I have a couple questions. I saw the balloon fill presumably with hydrogen. where was the oxygen displaced to? what clearance between the pates did you use?I have a 13.6vdc 19 amp power supply. would that voltage be too strong? do you have any recommendations as to how to store the gases for later use? since salt can be used as a dielectric this could possibly be used as an underwater self contained breathing apparatus.
the oxygen and hydrogen were mixed in the balloon because both the anode and cathode plates were together. Its generally safer to keep the hydrogen separate when storing (its less combustible). Honestly you could store it in 2 liter soda bottles if you are careful enough (do at your own risk) although that would be very difficult for something to go wrong. The optimal voltage gap between each plate is about 2 volts. Your 13,6vdc would produce a lot of excess heat because of the high voltage. Use neutral plates to lower the voltage and increase efficiency (Im sure you can find a plethora of things on the internet on how to use them. Although you should use about 5 between positive and negative plates). It could be used as a breathing apparatus if enough energy were present. Submarines sometimes use this tactic to continually have a safe supply of oxygen. Then again these subs usually have nuclear reactors on board and have huge amounts of energy at their disposal.
no because the process produces chlorine gas which will kill you. unless you use sodium bicarbonate in lieu of salt which everyone should be using!
@@Rand_al_Thor372 or Potassium Hydroxide, which is significantly more effective than baking soda.
Nice Video! can i use soda ash as an electrolyte for the hho generator?
What a great little system. clean build. so I can build this and suppliment my vehicles fuel with a couple devices like this?
It is better to spend your money on a tune up. On a well tuned engine, adding a mixture of hydrogen, oxygen and water to the intake does nothing useful.
Great! But what about adding a bubbler(to be safe because hydrogen is flammable) and sanding the plates b4 putting them together? (sanding=more surface area= more surface area where reaction can happen :p)
Very nice and clear video, im just wondering where does the oxygen go? how can it be improved so that the oxygen can be extracted separately? Thanks for the video
The oxygen leaves the electrolyzer mixed with hydrogen, making brown’s gas. This is called a single output cell, whereas a split output would have two separate electrodes that have an isolated output, but still have electricity flowing through them.
Great design but u should have a bubbler to prevent any flash backs
If you use salt then it's not hho its hhc, hydrogen and clorine
Salt only allows current to flow . HHO is the end product, no matter what you use the electrolyte . The only difference is the efficiency of the generator , the electrodes wear and the minimum voltage of the water splitting
But the clorine in salt will get relised with the hydrogen while the sodium and oxygen bind and stay in the water.
But either way atleast the hydrogen will still get relised.
You're right :) I had to check it , actually part of the oxygen will react and will be in the water. But the most important gas generator (hydrogen) will be evolved without a problem :)
+M.N. Projects Please do not use pure salt as electrolyte, since the chlorine gases that are produced with it are highly toxicy. Youre better off using regular baking soda.
i agree with you. that's why i didn't like this video
how did you build the core tho? video?? or guide anywhere? and wont the plastic melt after it heats up? why not use mason jars and why salt and not pure baking soda?
This is cool.. but what is it used for? I'm trying to find ways to make a home generator for in case of power outage. I guess I'd like to start with the strength of something that can power my grow lights if the weather outside is unreliable and cold, but have no power indoors like nuclear winter.. but if I can make something that could also run fridge etc that wouldn't hurt. Any suggestions? Thanks either way and God bless !!
i made mine with random parts i found around the house
You could sell a lot of these on eBay I would buy one
nice vid. have u tryed to use the left over water to do ur laundry?
first of all, i like your work very much cause you concern for the little details,,
but as i learned years ago, this operation produces oxygen and hydrogen, which are mixed in your balloon
am i right?
THE MOST OF PEOPLE THINK THAT " WHO TO STORE THE HYDROGEN GAS" BUT HE DO SIMPLE THING AS USE BALLOON....
$5 after or before buying all those tools needed for the project? Smh
nice attempt, and except salt as electrolyte, that gives chlorine, it is cool. you used 2V and 10A surprising as most use 12V dc supply. I am surprised to see Earth kind of thing, that connection I did not understand though (yellow wire), All the Best for more such experiments.
Heilium and hyrogen are lighter than air, remember the Hindenburg zepplin?
Sorry if it's a dumb question but where does the oxygen go? Does it only produce hydrogen?
Is the Output Energy stored in gas about the same as the input, or is it more because a lot of energy comes from the hydrogen in the water or something like that
The output energy is lower because perfect energy transfer is near impossible. It can’t be higher because of the laws of thermodynamics.
Add 7 neutral plates between positive and negative and you won't get the water heating up. Otherwise your losing a fair amount energy to heat loss.
The generator is powered by voltage of 2V , little more than the minimum voltage distribution of water. Neutral electrodes are used when you want to power the generator a higher voltage. Then we obtain as if several generators connected in series. Between the two electrodes voltage should be about 2V :)
Ddroyd1 A
7 plates total, 5 neutrals. For 12/14v systems : 2 volts per cell, no heat is made, your energy makes MORE GAS! Seal them to, from each other. No high voltage leakage.
Yes from Bob's 1981 Gag Ordered Patent, Sealed, series H2O cell design. - hydrogengarage do calm / store
very nicely presented and very helpful, next video make an industrial large one
If you want, you can sand the alluminum plates for more contact surface.
Aluminum plates does not rust , but quickly covered with oxides. Then the efficiency drops significantly
I like the work so much, is there anything like positive and negative in it?.
Nice video and good job
Motorbike runs on water | HHO | hydrogen gas generator | without petrol | with proof
#Raselhomemadecreator
I wonder, could this be done on a larger scale say... About the size of a 55 gal drum? If so how much amps could it produce??
If you are in a warm climate you can generate hho by simply filling your gen. & putting it in the sun,there is enough electricity in the air for modest production for free,no joke Phil
No there's not. Every chemical reaction CAN happen spontaneously on a small scale given enough potential occurrences to overcome the statistical unlikeness, but H2O is by FAR the more chemically stable state compared to H2 + O2, and in a mixed environment of H20 + H2 + O2, the spontaneous reactions will trend towards more water. The trivial amount (I'm talking single digit count of molecules,) of H2 + O2 that form off of water would be imperceptible to anything but the most technologically advanced testing devices, IF even then.
Why do you think we don't have H2 in the atmosphere even though 70% of the surface of earth is water?
dont use Salt !! instead take baking Soda/powder
for the plates Copper
Copper will corode.
Sondre Dammen Søgård you have to replace any Material from time to time
OK but i have experienced that stainless steel lasts much longer than cobber. But you might be right. Im not a scientist. 😃
Produced more using those correct ? Soumds correct
@ We aren't drink electrode water.
Baking soda works a lot better and a cap full of White vinegar keep corrosion down on the copper wires and steel
how fast youll have to box the ballon to get it explode?
or isnt it know as "knallgas" ;) be cautious
Cool :)
How about using aluminum foil? Does it work?
and clothes pins holding wires onto them
and plastic bottle caps cut like washers
And how much amperage can 2 volts carry? (voltage is a path to current)
Why did you use salt and not baking sofa?
I'm one of your Subscriber as well bro
It's nice very good idea
would this work for my van's engine?
Exelente video gracias por enseñar sin ningún egoísmo gracias
was gud. could u post some video to show how efficiently u can harness the gas produced. and by this exp what could be the output by harnessing the gas produced
what type of jar which you are use ? glass / or plastic?
WHO THE HELL WOULD NEED THIS??!!
BUT ITS STILL F**KIN AWESOME
People want to breath the gas. Says it cures diseases. Sure will if it blows up or burns your lungs out.
why u put terminals to side of bottle, use the (force) cover for this.
With constant operation, how long does the generator last before parts start to corrode?
about everyweek to 2 weeks youll need to change the conductor
I would just like to know where one gets a 2V 10A battery. Speaking of, 10A is HUGE!!! In the range of a gulf cart battery, and they go for about $200 USD. Great video until he tossed in a wrench. Make a video using AA, AAA, C, D, 9V, or 12V. That is what we have in America. Then again, maybe I should do one using off the shelf American parts. Look for a relavent video on this subject on my chanel in the near future. As much as car makers dance around electric technology, Hydrogen is where we are going because 250 unit apartment building in NYC can't charge batteries with solar panels.
How about showing how to make one that separates they hydrogen from the oxygen?
just have your two separate electrodes far apart. You can do this in an open tub of water, the hydrogen will form at the cathode (positive terminal) and the oxygen at the anode (negative terminal) if you put an upside-down container above the bubbling cathode you should start collecting hydrogen because it is less dense than air.
cool. But a bathtub would be a little hard to carry around in your car to use for fuel production LOL
Justin Bank about how far apart and I placing the electrodes?
+Larry Burks by tub, I don't mean bathtub, it could just be a bowl.
+SupremeStigma it shouldn't matter as long as the resistance of the water isn't too much. You pretty much just want them far enough apart that the containers you are collecting the gases in don't collect a bit of the other gas. If you don't want the gas collected to be contaminated by air, fill the container you're collecting in with the water, turn it upside-down while submerged, and lift it slightly above the water above the electrode, so that the closed end of your container is above water, but still full of water because of suction. You can then keep it in place with a clamp or something like that.
What type of torch were you using?
Excelent!!! Bv, bv, bv...,❤️👏❤️
nice job mister
M.N. Projects
ماشاءالله عليك👍👍👍👍👍👍👍👍👍🌹🌹🌹
I think it was first demonstrated in Philippines when a filipino inventor used water as fuel to run an engine...
is 19.5V, 3.3A and 65W (Laptop charger Output)enough for electrolysis?
If yes how much HHO production can i expect?
Pls answer it'll MEAN and HELP a LOT.
How many volts and ampers did you use here?
This guy knows what's up
Hydogen is not a heavy gas - It's lighter than air. It was used in zeppelins until the Hindenburg tragedy. Just sayin'...
He said heavily flammable, not heavy in the sense of mass.
first engine ever built, ran on hydrogen. gas/diesel came 100 years later, cause its cheap.
Thanks dude, that's really interesting
je réponds je suis français de souches et je peux te dire que ce que ses personnes disent est faut et je t expliques pourquoi ce sont les frères mongolfier qui ont inventé les premier au monde l utilisation de l air chaud par l invention de la mongolfiére il y à de cela plus de deux cent ans dans le passé et ils ont fait voler la première mongolfiére au monde devant louis 16 bien avant la révolution française et oui les français sont les premier au monde à avoir voler dans les airs qui dit mieux d après toi ?
john pages, Ils parlaient des zeppelins (ballons dirigeables allemands), pas de la montgolfière. Et tu dis être français de souche, certes, mais l'anglais faudrait le travailler un peu, tu comprendrais mieux "ce que ses personnes disent"...
what glue are you using?
what about the matel sheet please define the metal name like a brass, steel, silver or iron sheet used for preparation of cell please bro. Thanks
nice one ;) mabye you will make a other vers. with copper plates ;) Namaste
Get more surface area with honeycomb plates and have them Crome plated
Can I fix this on my vehicle ?
stay safe stay connceted 🤝
What is the first music track?
Can you add all mesurments and elements this generator was made of?
Where can you find stainless steel sheet metal cheap?
In your kitchen cabinet--think turkey.
You mentioned this being a generator does this mean i could derive electricity from this?
This generates hydrogen gas not electricity. Although you could burn the hydrogen gas to make electricity, it wouldn't be efficient.
can you put baking soda instead of salt?
Yes
what was the first song?
Heavily Flammable...
And highly explosive, oxygen supplying Hydrogen's burn reaction.
2 VOLT 10 AMP ??????? MAKES NO SENSE,, THINK YOU MEANT 12 VOLT
if more than 2v it shall burn.
no you are wrong it can produce Hydrogen at 500KV
mw10259
A single cell on a battery produces 2 volts, your car battery has 6 cells producing 12 volts.
2 means 2 volt not 12 vol.
is that a plastic jar??
great video... You should sell them
YOU ARE SUPPOSED TO USE BAKING SODA AS ELECTROLYTE UNLESS YOU HAVE AN AFFINITY FOR CHLORINE GAS, OR JUST ENJOY THE WAY IT SMELLS.. lol
yaa afcause
Nice work. How long did you do this?
I dont remember, I did it in my free time. But if you want, you can do it in one day :)
Whicg part did you get stain less steal pls said
whether the plates can touch each other
M.N. Projects what do you do when the ballon cant take anymore
Ive seen people have their cars run off this and make welding machines out of it.
You should replace salt with sodium hidroxide (NaOH) or anithing else, because if you use salt (NaCl) in electrolisis, you obtain chlorine (Cl2) wich is very flammable and toxic instead of hidrogen (H2)
Frank Gutowski You´ve right but toxic!
its exactly toxic, it just binds with water in your skin to form HCl and HClO
Baking soda is good idea?
you forgot the bubbler
That is just for safety reasons incase you want to light a fire on the other end
its not a bong, bro...
so what, Jason?
good job.
heavilly flammable?
Lets look at the cost as you used a soldering gun, drill, drill press, screw driver, pliers,heat gun,silicone,and somehow I think the total cost is above 5 bucks. Having copper wire immersed with your Stainless steel means your wire will disintegrate far faster than the stainless. Proof of concept yes , cheap no.
No only hydrogen is made oxygen is also made does it work on a motor vehicle without problems
No flashback arrester?
cool idea man! i will try it! thnx
Wow
Run a generator on this and fuel vapour so not to overheat the head. Easily done, but then Governments could not blame us for global warming and tax us for it!
Hi, using salt (NaCl) isn't the best idea. You would create hydrogen yes, but clore gas too. Just as little info clore gas was used as chemical weapon in WW1 and it could hardly demage your engine, also NaOH the new salt formedin the bottle must be trated carefully. Hight concentrations can you make blind.
3:17... i saw that finger going off... xD
Salt water makes chlorine gas. What are you going to do with that.
choke.
hi it's me Mr creature i'm really sorry for your dissapointed..
and i'm here for retract and it will not be repeated ?
i'm waiting for you good response thanks...
How much voltage it can be made?
Does this generate enough gas to supply one of the small jewellery Hydrogen Torches? Looks like it just mite.
I dont think so. Hydrogen Tourches need much more gas than this generator can produce :)
You would have to do several of these generators and connect them
well if you loose 70% of your air its pretty bad
you can buy a full setup for about 200 dollars
A setup doesnt need that tight seals to store hydrogen. Hydrogen storage only becomes a big problem once its pressureised
what is the name of the first song?
pack the powder what ko inserted into the water please immediately reply
Ich konnte nicht genau erkennen, was das Ziel sein sollte. Aber jene Anordnung ist nicht zu empfehlen, denn die zersetzt Wasser und Salz (NaCl ?) in gefährliche Komponenten: Chlor, Wasserstoff und Sauerstoff. Der Luftballon ist am Ende also keinefalls nur mit Wasserstoff gefüllt !! Wenn man da eine Flamme dranhält, kann es heftig knallen! Und auch schon bei der Elektrolyse kann das Ding explodieren. Hier sollte also noch mal nachgebessert werden.
now what are you going to run this to? your car? how about a lawnmower with a small generator on it to power the cell once its running and recharge a small battery?? ;)
Are you using table salt for this?
Yes. Much better is NaOH or KOH, but if you want do it in the simplest way you can use table salt
+M.N. Projects It's a great video. you should add an annotation telling people to use one of those if they can, or otherwise be careful with normal table salt as it produces chlorine gas instead of oxygen.
+Natabu Azamari 👍👍👍
can i use sheets which made from aliminium?
not for long due to the high corrosion rate of aluminum, hence the need for stainless or better instead of copper which also corrodes super fast in electrolosis.
gold, silver or platinum are all ideal with platinum showing the most corrosion resistance.