1 A nice touch to overlay the crucial parts with big letters to clarify. 👍 2 Increase DPI, and picture will be less blurred. But don't stop doing no 1!
DigiCDC has become a hassle to compile, and hard to use (I hear) in Windows. Have used it quite a bit though. With a protective resistor, it is possible manage TX+RX on a single line. Add a CH340N to your dev board with this rig, and it may be possible to serial-print and and run a bootloader with with just the Reset and one data line, freeing 4 pins for GPIO.
What about the different Attiny support boards? I use the SpenceKonde ATTinyCore. Do you recommend the dmellis Attiny or are practically the same? Thank you very much. I love these Attiny85 videos 😃🤟🏽🤟🏽🤟🏽.
Thanks Marshall100w6 🙂 The SpenceKonde is the most compete one if you know what you are doing, it also includes versions without bootloader etc. and does not use up much flash memory, I really recommend this one because it enables you to play with other types as well (Atiiny 25,45, Attiny 13)... In this video I used the dmellis one, because it is easy to use for beginners (...after you flashed the bootloader), and it is reliable using a FTDI. The Digistump looks great but does not always work because the USB is not a standard USB.
Hello Mr. T does this work with any type of UART adapter? Cause I am getting this error: avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x20 avrdude: ser_drain(): read error: Device not configured thank you so much
Hi Hirotosiken-san, yes I think it is possible, though I did not do that myself. Please try this link: www.studiopieters.nl/attiny85-oled-i2c/ . The information looks reliable.
would love to see some videos on new attiny series
1 A nice touch to overlay the crucial parts with big letters to clarify. 👍
2 Increase DPI, and picture will be less blurred. But don't stop doing no 1!
DigiCDC has become a hassle to compile, and hard to use (I hear) in Windows. Have used it quite a bit though.
With a protective resistor, it is possible manage TX+RX on a single line. Add a CH340N to your dev board with this rig, and it may be possible to serial-print and and run a bootloader with with just the Reset and one data line, freeing 4 pins for GPIO.
Super helpful. Thanks!
Happy to hear that!
Great video! Thanks for sharing. Subbed..
Great to hear txflier!
What about the different Attiny support boards? I use the SpenceKonde ATTinyCore. Do you recommend the dmellis Attiny or are practically the same? Thank you very much. I love these Attiny85 videos 😃🤟🏽🤟🏽🤟🏽.
Thanks Marshall100w6 🙂
The SpenceKonde is the most compete one if you know what you are doing, it also includes versions without bootloader etc. and does not use up much flash memory, I really recommend this one because it enables you to play with other types as well (Atiiny 25,45, Attiny 13)...
In this video I used the dmellis one, because it is easy to use for beginners (...after you flashed the bootloader), and it is reliable using a FTDI.
The Digistump looks great but does not always work because the USB is not a standard USB.
@@smartpowerelectronics8779 Thanks again 😉.
Hello Mr. T
does this work with any type of UART adapter? Cause I am getting this error: avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x20
avrdude: ser_drain(): read error: Device not configured
thank you so much
Were you able to program it as described in the previous video? (ua-cam.com/video/5__0aKdqlDQ/v-deo.html)?
hello from France, in this diagram pin 7 of the attiny85 is not connected? is this normal?
Hello regisrobart! I connected an LED with a 330Ω resistor to PIN 7, for the Serial Print function it is not needed.
Thanks, but why such a low resolution 480? Ok, I understand you replaced your PC with a ATTiny85 ;-)
ehm yep, for this video something went wrong with the video processing and I did not keep the raw video.....
ありがとうございます。OLED LCDに表示することが出来ませんか
Hi Hirotosiken-san, yes I think it is possible, though I did not do that myself. Please try this link: www.studiopieters.nl/attiny85-oled-i2c/ . The information looks reliable.
FTDIだけで完結できる点が素晴らしい
また、ブログなどありましたらご連絡お願いします。ありがとうございました。
Thank you @hirotosiken! ...No I do not have any blogs, only this UA-cam channel.
if you try again, fix your audio BYE
Super helpful. Thanks!