Awesome! The battery barely wants to run out, for me it jumps down to 3.9 almost immediately! I'll be curious to see the lava 300mah batteries now (they're on their way) :) Are the motors soldered?
@@TargetFPV Hi! Yes, the motor wires are soldered. There where no other option because the BetaFPV Air 5in1 AiO (not Matrix) doesen't have plugs. I think this flight was on GNB 380mAh, which where almost new. Do not go below 3.3V in Lavas, they bleed out voltage very quick below this level.
@@drony3miasto I also had it soldered ,but after the vtx ufl broke off (same aio), I replaced it with a matrix ,but it's still good! Thanks for the lava tip, I have 550mah for a while now and they are pretty good ,but now I will watch out not to over drain ;)
@drony3miasto it doesn't matter which cable of the 3 that goes to your camera. I've had something like that a lot and the interference in the picture was the same. 😅
@@YouFPVtube The interference you see in this video is from shitty cobra x v2 goggles default receiver. It turnes out, is is common and kown issue. I already replacet it with better version. Too bad, I did not know i ealier, before I bought the googles...😕
@drony3miasto ok. As long as you can solve the problem everything is fine again 😀. In my case it was the cables that were hanging on the contact with the last thread
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Build inspired by Grox. Please check his video: ua-cam.com/video/To3iky9ET88/v-deo.html
to już całkiem niezły czas lotu :)
Dzięki :) I jeszcze był potencjał na lekko dłużej - na baterii można by było do 3,1V zjechać... hehe no ale ale ile można.
Awesome! The battery barely wants to run out, for me it jumps down to 3.9 almost immediately! I'll be curious to see the lava 300mah batteries now (they're on their way) :) Are the motors soldered?
@@TargetFPV Hi! Yes, the motor wires are soldered. There where no other option because the BetaFPV Air 5in1 AiO (not Matrix) doesen't have plugs. I think this flight was on GNB 380mAh, which where almost new. Do not go below 3.3V in Lavas, they bleed out voltage very quick below this level.
@@drony3miasto I also had it soldered ,but after the vtx ufl broke off (same aio), I replaced it with a matrix ,but it's still good! Thanks for the lava tip, I have 550mah for a while now and they are pretty good ,but now I will watch out not to over drain ;)
@TargetFPV Lavas have much shorter lifespan than standard blues from BetaFPV. Even when are not overdrained. Happy whooping!
Your camera cables have loose contact
The red wire? It is ELRS anthenna:) But already I have better cable management.
@drony3miasto it doesn't matter which cable of the 3 that goes to your camera. I've had something like that a lot and the interference in the picture was the same. 😅
@@YouFPVtube The interference you see in this video is from shitty cobra x v2 goggles default receiver. It turnes out, is is common and kown issue. I already replacet it with better version. Too bad, I did not know i ealier, before I bought the googles...😕
@drony3miasto ok. As long as you can solve the problem everything is fine again 😀. In my case it was the cables that were hanging on the contact with the last thread
@@YouFPVtube yeah... tough fpv life :) there is always some issues, but we never give up! stay strong💪