How to calibrate ESC / Throttle of your Drone. How to make drone Part - 2
Вставка
- Опубліковано 28 лют 2020
- #esccalibration #throttle_calibration
Learn how to calibrate your drone.
Is your drone is not flying ?
Is your drone is not getting stability ?
Is your drone is crashing ?
Follow our video tutorials for it.
Roboguru UA-cam channel
/ @robogurums
All at once calibration
Turn on your transmitter and put the throttle stick at maximum.
Connect the Lipo battery. The autopilot’s red, blue and yellow LEDs will light up in a cyclical pattern. This means the it’s ready to go into ESC calibration mode the next time you plug it in.
With the transmitter throttle stick still high, disconnect and reconnect the battery.
For PX4 or Pixhawk, press and hold the safety button until it displays solid red.
The autopilot is now in ESC calibration mode. (On an APM you may notice the red and blue LEDs blinking alternatively on and off like a police car).
Wait for your ESCs to emit the musical tone, the regular number of beeps indicating your battery’s cell count (i.e. 3 for 3S, 4 for 4S) and then an additional two beeps to indicate that the maximum throttle has been captured.
Pull the transmitter’s throttle stick down to its minimum position.
The ESCs should then emit a long tone indicating that the minimum throttle has been captured and the calibration is complete.
If the long tone indicating successful calibration was heard, the ESCs are “live” now and if you raise the throttle a bit they should spin. Test that the motors spin by raising the throttle a bit and then lowering it again.
Set the throttle to minimum and disconnect the battery to exit ESC-calibration mode.
Donate to.
Roboguru@uboi
APM 2.8 based drone
• APM फ्लाइट कण्ट्रोलर स... - Наука та технологія
Very very very very very very thanks sir I have not word for you 🥳🥳🥳🥳🥳
Mostly welcome keep visiting and don't forget to Share and subscribe
@@MSExperiments sir why do we need Esc calibration after restart
Not need to calibrate ESC every time
@@MSExperiments but drone motor continuing beeping why after restart
Flight controller problem maybe
Bro but when we will open the esc from the pin board and again attach to the kk flight controller will it work fine ?
Yes
Thank you
Keep visiting
Bro then if we detach the wire from PCB and again attach to the same pins in flight controller and reciever then will it be OK?
Yes
My ESC calibration is done, KK2.1 shows throttle pass through. But when I use the throttle key motors not running.
can you help ??
Check kk flight controller settings. If calibration is ok.
After esc calibration we should attach the wire to flight controller or we should keep in the pcb
please help me fast
Of course brother after calibration connect it to flight controller
will it work in the APM 2.8 flight controller and my drone motors are not spinning would it be fixed by making this device ?
Yes
My naza m lite after computer calibration and settings contunuesly blinking on red color mode, can you help me
Change mode
👌👌
🙏🏻
Ab calibration ke baad isko disconnect karke dobara wese hi laga dena hai ??
Ha
can you give me the link of esc calibration board online please!! so I can purchase it online
because I don't have the pcb available in my area
Do you have bread board ?
If you have calibration it by using it.
Connect all ESC in parallel by using jumper wire.
Great content. Keep it up! Would you like to be UA-cam friends? :]
Thanks for your valuable comment.
Yes i love to be friends
Having an issue that when my drone got armed motors are not getting rotated at a tym only one or two are rotating and when i am moving throttle up slowly up rotating got stops and then its cmng from first displays as SAFE, if again when i arm same problem repeats
Help me with this bro please
ESC calibration error follow my video to calibrate ESC properly.
With out propeller all motor spin good but when i set the propeller then motor try to spin but couldn't. Can you tell me where is the problem.
ESC power wire was not connected properly
Bro can I calibrate it without making this hub by connecting it on the NASA itself
No brother
Bro esc calibrate karte waqt jaise hi throttle ko down karta hun to drone ke esc continues beep dene lagte hai kya problem hai please reply bro 🥵🥵
Loose connection maybe
4200mah, 35C battery
920kv motor
Ke sath ready to sky ki 40A ESC laga sakte hai kya??
Kyuki mujhe 30A ESC mil nahi rahi kahi bhi
Or flower dropping drone ke liye use karna hai to kuon see sahi rahyegi jo available bhi mil jaye
30 amp ki esc nhi mil rhi to usse upar ka koi use kr ligiye jo available ho
@@MSExperiments achha
Bhai mere drone me pixhawk flight controller me jo reomte hai usme jab thortel ko full bada te hai tho sir 2 hi motor rotate hoti aur agar right side ki joystick ko motor ke direction me move kia tho jo motor nahi chal rahi thi wo chal jati hai aur jo motor chal rahi thi wo band ho jati hai plz mere problem solve kardo
Esc calibration error h
Bro when ever I try to connect with receiver I was unable to connect ,
First I connect with my receive then unplug the power to drone then up my speed key then on reconnection to power to drone , it was unable to pair the receiver with drone, I have the same receiver and transmitter , help me bro please
First bind your transmitter with receiver
Or contact me on Instagram
Bro mera sat ek problem aa gayi hai mera jo transmittar ka 3 mode switch jo hota hai na woo work nahi kar rahi hai matlab switch jam ho gayi hai kay ham usa change kar sakta hai plz bhi bata doo bhot problem mai hoo
Ha toggle switch se
does it wok for pixhawk 2.4.8 ?
Yes it will work ☺️
Bro my drone motors forget esc calibration everytime i turn on it any idea? Please reply 🙏
That's due to loose connection
What is battery aize your using
It's 5200Mah battery
How will u control it forward backward turn etc cause whatever the command u give all the four motor will have the same rpm and so the drone will just go up and down......hope u understand my point
By controlling each motor speed through controller we can move it forward, backward,side wise even circular motion on fix axis....
@@MSExperiments but how each motor will get the same input current as the other as u have joined all the motors to only one channel so the current going to all the motor will be the same....
All motors are connected to ESCs and trough ESC we are controlling the speed of motor and each ESC DATA pin is connected to flight controller for controlling the speed of motor.
And in ESC calibration video all ESC data pins connected together..
@@tanaymehta4188 that is done only while calibrating the escs. after they are calibrated we connect them back to the flight controller
Good
hey bro can you help fix my drone, it won’t go up while the throttle stick is up pls reply I need you
Share detailed information about your problem
Hi i had face the same problem, but now got resolve 👍
Great 👌🏻.
Keep visiting
Same problem
Help me anna
Please share your problem
@@MSExperiments drone is not flying
Massage me on instagram
Bhai DJI naza m lite me x2 port se kya hota hai ? Ager connect nhi kre to kya hota he pls reply
X2 telimetry me use krte h generally aapko nhi connect bhi rhega to koi dikkat nhi
Bhai mai jab apna drone gps mode me fly ker rha hu to fly krne ke 1se2 min ke bad dron alttitude hold mode me aaja rha hai aur gps show nhi ho rha , aur dji naza m lite assistant me bhi gps ka option hi nhi aa rha please reply 😢
@AKHIL_SINGH2007 GPS disconnect ho ja rha h.
Ek bar firmware update krk dekhiye aap
Bro mere dji naza v2 mei problm ho raha hai mei jab power de raha hu led red or green blink ho raha hai kase solution karu?
Aap mode ki setting kigiye. Software se
ager kk2.1.5 flight controler hai to
Aap directly kk se bhi calibrate kr sakte h.
Aur jaisa maine bataya waise bhi
naza flight controler se ppm mein conection kaise hoon ge
Aap video follow kigiye aur bhi video bana rakhi h maine
My motors are not spinning properly after Esc calibrate..
Great 👍 keep going..
Good luck
Please show me how to trim/subtrim drone..
It's easy to do. Just follow the settings and there is option for that if needed i will upload a video on it
Sir aapne Arduino Uno se agar drone banaya ho to video ka link send kre
Ji maine aisa koi video nhi banaya h
Sir will it work for kk2.1.5
Yes work for all drones ESC calibration..
Sir my drone isn't flying
On full throttle it gets disarmed
ESC calibration or remote calibration issue
Bro my drone is not arming and led light blinks red and green I installed DJI naza m lite flight controller so what can I do please help me😭
Follow my DJI based drone programing video
Ok thanks bro☺️
Mostly welcome keep visiting. Please share
Sir jee main ne ek twin motor plane banaya hai par esc calibrate nahi ho raha....dono motors same rpm par nahi ghum rahi...kya aap meri help karenge plz?
Of course
Instagram pr contact kigiye
Sir je please give your whatsapp number ...instagram par account nahi hai
chat.whatsapp.com/I5lxSGuDk9UJutSaEBtqnX
Bhai mere me same problem aa rhi hai, aapke jaise karne par, sirf 2 motor beep kar rha hai fir chal rha hai, इसके बाद फिर बचे दो मोटर बीप हो जाने के बाद same पहले जैसे ही हो जा rha है
Bhai mera madad kar do
Sare ESC ko same time pr calibration kigiye
Bhi mera apm2.8 esc calibration ho jaegi
Bhai flight controller se calibration ka connection nhi h... ESC ko aap alg se calibration kigiye.
Aur baki flight controller ka calibration uske software se
My drone going to one side and I have done ESC calibration
Drone calibrate remote
Aap doran ki video banaaiye please.
Kiski video ???
Agar throttle upar karne pe speed kam ho motor kinto kya wo bhi esc calibration ka issue hai?
Nhi battery ka
@@MSExperiments battery me exactly kya problem?
Low current flow or voltage drop
@@MSExperiments 3 cell lithium ion battery hai new ,lipo battery nai hai to bhi chalna chaiyena? Mah same hai
Acha aap ek baar Instagram pr clip bhejiye
One motor is spinning Continuesly please help
Change esc
Bro when ever I try to fly my drone on of its motor is not rotating, can you Help me??
Of course i will help you 😊
Please share more details.
You may contact me on Instagram 🙂
@@MSExperiments bro can you please share your instagram id
Check out channel about section.
Or @ms_experiments
After Calibration, facing same problem ,please help
flight control ?
And software version ?
@@MSExperiments Apm 2.8 flight controller
Software version ?
I did the same. But when I connect it to flight controller, Motors keep beeping
Loss connection or low battery
@@MSExperiments no I cheaked... Battery was full, connection was ok...
Kya Bhai esc calibration se drone stable pe udega
Ha bhai esc calibration se stability pr bahut fark padta h.
ESC calibration kiye bina maine dikhaya h ki kya issue aata h
Bus transmitter and flysky receiver se kam chalgayga ya flight controller Jaise kk2.1.5 controller jarruraat hai ?
Sir iska staring ka video to apke channel m ni h
Video dala to h aap check karo ek baar
मोटर स्लो रिस्पाँस क्यों देती होगी
सिंगल मोटर RC airplane
Kya matlab aapka ?
Hii mere esc calibration hone ke bad bhe motors armed hone ke bad beep karte he , DJI nasa m lite me
Software version change krk try kigiye ek baar calibration software se
@@MSExperiments version update he
@@MSExperiments aur yek yek esc ko seperately calibration Kiya toh bhi beep ho rahi he
Old version
hey I’m facing this odd problem that when i connect the motor to the receiver and try to calibrate it using the controller the wrong joystick is activating the motor i have tried changing the mode but that doesn't work. when i do motor test on the naza m AS only motor 4 spins and nothing else.
link to the video
ua-cam.com/video/eAdWXPjt1uw/v-deo.html
Contact me on instagram
Bhai maine drone banaya hai , pehle chalu hua tga but software installation ke waqt kuch hua pata nahi , abhi battery connect karne ke baad bhi motir beep sound nahi araaha hai aur , throttle ko up karne se kuch nahi ho raha hai
Flight controller reset kigiye
@@MSExperiments bahut bast kiya , i think battery got discharged let me charge and then i will try thank u for the response sir
Keep going.
Feel free to contact
@@MSExperiments thanks bro
Mostly welcome keep visiting
Bai my drone is not flying cc3d flight controller
Not used yes cc3d flight controller.
Send me pictures and other details on Instagram possibly i can help
Bro your I'd bro instagram
@@JACK_CLIPS_01 instagram.com/ms_experiments
How to identify cw and ccw propeller
Already explained in Assembling video in detailed.
Please watch that for better understanding.
Thank you ☺️.
Fill free to ask.
@@MSExperiments just now watched thank you and i've made a drone tx is ct6b to arm i drone i have to move throttle left instead of right. what could be the reason?
My flight CONTROLLER is kk 2.1.5 which has black buttons on it
And also explain about self level
Change remote channel to reverse.
ppm to naza wiring kaise hogi
Contact me on Instagram
@@MSExperiments instagram link send me
Please search @ms_experiments
Quuen me puede alludar?
What it means ?
Sir jo kit use kre h uska name lga dijiy plz🙏
Flight controller DJI NAZA M LITE.
Remote fs i6
Aap KK flight controller use kr sakte h . Sasta aata h.
DJI NAJA M-LITE aap muzhse kharid sakte h km daam me.
Sir ,drone camra ka video chaiye
Ji Drone camera ki video jald aarhi h.
Video shooting hogyi h bs editing baki h
Sir edit hua ki nhi
Drone camra ka
Hello sir I need help I use apm2.8 in Quadcopter and my drone is automatically rotate left side on its axis try everything like yaw trim but nothing is working please help me
Brother 3rd part?
There is no 3d part
bro meri two motor rotate hi nahi ho rahi he to me kya karu?
Esc calibration sahi se kigiye.
Aur motor ki wires ko exchange kr ke dekhiye
@@MSExperiments bro meri 4ro motor rotate ho rahi thi phir mene jab tumhare jesa hi calibration kiya to do esc bigad gaye or motor rotate honi bandh ho gayi.
Mene ye 2 or 3 time sahi se kiya tha
@@dineshpatel-gm8ji possibly connection ka issue ya fir ESC kharab rha ho .
Aap Instagram pr contact kigiye waha connection share kigiye
@@MSExperiments lecit bro mere connection kara ne ke bad 2 esc bigad gaye
That's manufacturing fault.
Bro calibration kar lia par . Flight controller me set karneke bad pahele jesai ho gaya 🙄
Kya mtlb aapka ??
@@MSExperiments matlab koi faida nahi hua ...
Acha instagram pr clips bhejiye aap dekhte h maybe i can help
Contact karna hai aapse
Instagram please
@fundoopilgrim or @ms_experiments
Mera problem hai fly sky me
Kya problem h ??
Ok but something is wrong ,🧐
What's wrong ?
@@MSExperiments
कुछ नहीं बस यह ऊगली कर रहा है😂😂
@@JKROBOTICSshorts acha ji
अरे चचा टोटल खर्च कितने का होगा 🤔
9000 me bhi ban jayega aur usse jyada me bhi .
Sirf Ek Motor Beep kar rahi
ESC change krk dekhiye
@@MSExperiments saare ESCs ki jo beep kar rahi hai
Sara jo beep nhi kr rha