Want a 182 of your own? Consider purchasing one via our affiliate link: www.fmshobby.com/products/fms-1500mm-cessna-182-pnp?_pos=1&_sid=c80c621f5&_ss=r&ref=Hm97_0xLEWLYuu
@@AbdullahNajib-b9zsadly there aren’t many trainers on the market for that price. Family makes a pa18 cub for 200$ usd. They also sell the ranger for 229$ But what I would reccomend is the Hobbyzone Aeroscout, ready to fly is 199$ and Without a battery and transmitter is 179$
I'm pretty sure Jon would advise that you set all of the servo travels to 150% and shove the battery into the tail for perfect high alpha setup. Assuming you've already split the flaps, ailerons and elevators out, installed a 10+ channel Rx and use half a dozen mixes for gains, throttle and various wing configurations. Easy peezy! 👍 Jk, Jon! Brian made me do it 😊
Theres something called a wedge washer that will 100% fix your slanted wheel issue. Just add the washer to the side of the axle that doesnt sit flush and it will then be flush!! Nice project!!!
Hold up I’ve just had a light bulb moment. Put Uma Grip on the tail to slow down even faster. Also probably less likely to nose over. Also you guys r obsessed with uma grip so the more the better right?
We didn't have issues with it nosing over for normal takeoff and landings. Trying to purposely fly the tail while holding down elevator is what did it in.
@@TailHeavyProductions ye it looked pretty good for this one I was just thinking about it in general for other aircraft like the viper bush conversion. Also mainly just because it would make the plane slow down faster (more friction)
Love it, you make me feel better about my repair ability. I'm better at flying into fences. Love the creativity. I would like to try PCBway for parts, but I don't have the ability to design them myself. Do they help with that?
That was funny, but why so long between videos? I get that new england is freezezing, its 30 degrees in texas, but you said to just get hand warmers and transmitter muffs and go fly anyway.
Check out our community post from a month or two back. Life is busy for us these days - but we're doing our best to fit in what we can for uploads! Thanks for watching.
The idea was to mount it to an existing hard point on the fuselage. The location of the tires is where they should be on any tailwheel airplane: just ahead of the leading edge of the wing.
You guys are lunatics. I have a similar 182, but it's got a one-piece wing, so don't have to suffer through watching your mum through the damn ancient EGA connectors.
Want a 182 of your own? Consider purchasing one via our affiliate link: www.fmshobby.com/products/fms-1500mm-cessna-182-pnp?_pos=1&_sid=c80c621f5&_ss=r&ref=Hm97_0xLEWLYuu
i looked at the link
thats so expensive
are there any rc trainers you can get for under £140?
@@AbdullahNajib-b9zsadly there aren’t many trainers on the market for that price. Family makes a pa18 cub for 200$ usd. They also sell the ranger for 229$ But what I would reccomend is the Hobbyzone Aeroscout, ready to fly is 199$ and Without a battery and transmitter is 179$
I can’t believe you plugged it into a TV 😂😂😂 The best RC entertainment on the Tube. Thank you!
I'm pretty sure Jon would advise that you set all of the servo travels to 150% and shove the battery into the tail for perfect high alpha setup.
Assuming you've already split the flaps, ailerons and elevators out, installed a 10+ channel Rx and use half a dozen mixes for gains, throttle and various wing configurations. Easy peezy! 👍
Jk, Jon! Brian made me do it 😊
Sounds like a lot of work.
Theres something called a wedge washer that will 100% fix your slanted wheel issue. Just add the washer to the side of the axle that doesnt sit flush and it will then be flush!! Nice project!!!
There's something more entertaining about just letting the wheel wiggle, though. 😂
The CGi is incredible I can't tell if it's crayon or colored pencil
i think my rc plane scratch build may be too expensive to build.
for now,i am just watching you.
Nice experiment doing a tail dragger out of this plane. On the other hand a Bigfoot is already a tail dragger in a better size and flys great.
Been watching utube all day and found your channel, bloody marvellous and very funny cheers
Hold up I’ve just had a light bulb moment.
Put Uma Grip on the tail to slow down even faster.
Also probably less likely to nose over.
Also you guys r obsessed with uma grip so the more the better right?
We didn't have issues with it nosing over for normal takeoff and landings. Trying to purposely fly the tail while holding down elevator is what did it in.
@@TailHeavyProductions ye it looked pretty good for this one I was just thinking about it in general for other aircraft like the viper bush conversion.
Also mainly just because it would make the plane slow down faster (more friction)
Love it, you make me feel better about my repair ability. I'm better at flying into fences. Love the creativity. I would like to try PCBway for parts, but I don't have the ability to design them myself. Do they help with that?
How many timbers will carry my surron???😅❤
That was funny, but why so long between videos? I get that new england is freezezing, its 30 degrees in texas, but you said to just get hand warmers and transmitter muffs and go fly anyway.
Check out our community post from a month or two back. Life is busy for us these days - but we're doing our best to fit in what we can for uploads! Thanks for watching.
@TailHeavyProductions why was this video late?
Life is busy for us these days - but we're doing our best to fit in what we can for uploads! Thanks for watching.
@@TailHeavyProductions OK! Try letting us know if a vid is late next time please
Tasty
Also the gear looks like it should've been moutned further back and flipped around
The idea was to mount it to an existing hard point on the fuselage. The location of the tires is where they should be on any tailwheel airplane: just ahead of the leading edge of the wing.
You guys are lunatics. I have a similar 182, but it's got a one-piece wing, so don't have to suffer through watching your mum through the damn ancient EGA connectors.
This vid is mid.
GET O-
Your life is mid
The middle is mid
Bryan Philipps your daddy? or RC Saylors your daddy?
Your mom is mid.