Думаю вся разница будет в функционале прошивки и немного в схемотехнике. KSGER более известная марка и возможно будет получше в схемотехнике или в возможностях прошивки особенно версии с дисплеем, там по крайней мере есть память и можно прокалибровать станцию под несколько жал и создать для них отдельные профили. Это более бюджетный вариант, настроек меньше, но и цена была дешевле.
Не греется, нагреватель очень небольшой и расположен прямо рядом с кончиком жала, если сильно захотеть то можно жало на горячую заменить разве что обернуть его тряпкой, не путается. По поводу удобства тут зависит от ваших предпочтений, кто-то любит потолще, кто-то тоньше аля ручка. Тут по толщине примерно с маркер, мне удобно, но это индивидуально и именно поэтому подобные станции есть в продаже с несколькими вариантами ручки, различие чаще всего это толщина и материал.
Basic operation press and hold the encoder button and turn it on again to enter the paramter set mode. there are 9 menus for setting p00,p01,p02,p03,p04,p05,p06,p07,p08,p09,p10,p11,p12. P00 P00-restore default prameters(0 or 1,default value 0,0 is not restored, 1 is recovery) P01 p01-op amp gain(200-350 times, step 1,default value 270,) P02 p02-op amp offset voltage(0-250mv, step 2, default value 100,which means that the soldering iron head maintains the output voltage inherent to the room temperature op amp, if you do not measure, please keep the default value p03-increase the ttemperature, adjust the temperature ,30-50 ℃ ) P03 if you do not measure, please keep the default value p03-increase the ttemperature, adjust the temperature ,30-50 ℃ ) P04 p04-temperature adjustment step(0,1,2,5,10 degrees optional, 0 can lock the soldering iron temperature) P05 p05-sleep time(0-60 minutes,step 1 is 0, the sleep function is disabled) P06 p06-shutdown time(0-180 minutes, step 1 at 0-30,step 10at 30-180, disable function when 0) P07 p07-temperature correction(-30+ 30 degrees,step 1)(because the ntc resistor is in the chassis, the soldering station will cause the detacted ntc temperature to be higher than the room temperature, resulting in high compensation of the cold junction of the thermocouple, and the temperature of the soldering iron is not accureate. it can be corrected with this parameter. fro example ,if the detected soldering iron temperature is 20 degrees higher than the actual value,set this paramter to 20) P08 po8-wake-up mode (0,1,0 means that the encoder can be rotated in the shutdown mdoe and the handle can be awakened by the vibration handle. fro 1, only the rotary encoder can wake up ) P09 p09-temperatue plus strength(llight click on the encoder to error to enter the temperature for the shdden need to weld the solder joint) P-10 p-10 temperature enhancement time (enhanced time...) P-11 p-11 buzzer switch(o means off 1 means on) NOTE: Iron tip do not work continuously high temperature, high temperature work is easy to damage the tip! Ordinary solder melting point is 183°C, lead-free solder melting point is 227°C, usually the welding temperature is 300-380°C, 380°C is the temperature of the dividing line, higher than 380°C, iron head oxidation and loss is extremely fast, seriously affect the heating core life The Higher than 380°C temperature display will be beating, the higher the temperature, the greater the beating!Recommended in the 300-380°C for welding work, most of the work can be carried out, the temperature beating is normal, does not affect the use! The soldering iron used in this soldering station is a brand new soldering iron tip. Due to the unstable resistance of the new soldering iron tip, the temperature will jump or ERROR, which is normal. After several times of use, the stability will gradually stabilize. If you mind, please do not buy.
Спасибо за обзор. Вопрос, если вынуть вилку из розетки настройки сбиваются?
Нет настройки не сбиваются если она успела их сохранить. Сохранение происходит когда станция из меню выходит назад на отображение температуры
@@Константин-м6д Благодарю за полезную информацию.
@@John_Lancaster_Peck Вам спасибо за интерес. Пишите с удовльствием отвечу на вопросы.
@@Константин-м6д Подскажите, пожалуйста, чем отличается от KSGER на тех же жалах? Кто чей клон?
Думаю вся разница будет в функционале прошивки и немного в схемотехнике. KSGER более известная марка и возможно будет получше в схемотехнике или в возможностях прошивки особенно версии с дисплеем, там по крайней мере есть память и можно прокалибровать станцию под несколько жал и создать для них отдельные профили. Это более бюджетный вариант, настроек меньше, но и цена была дешевле.
а какой процессор установлен внутри станции STM32 ?
Плата управления на контроллере STC15F204EA
Главный вопрос, как ручка? Удобная, не греется, не путается в проводе?
Не греется, нагреватель очень небольшой и расположен прямо рядом с кончиком жала, если сильно захотеть то можно жало на горячую заменить разве что обернуть его тряпкой, не путается. По поводу удобства тут зависит от ваших предпочтений, кто-то любит потолще, кто-то тоньше аля ручка. Тут по толщине примерно с маркер, мне удобно, но это индивидуально и именно поэтому подобные станции есть в продаже с несколькими вариантами ручки, различие чаще всего это толщина и материал.
Hello, do you have a manual?
Basic operation
press and hold the encoder button and turn it on again to enter the paramter set mode. there are 9 menus for setting p00,p01,p02,p03,p04,p05,p06,p07,p08,p09,p10,p11,p12.
P00
P00-restore default prameters(0 or 1,default value 0,0 is not restored, 1 is recovery)
P01
p01-op amp gain(200-350 times, step 1,default value 270,)
P02
p02-op amp offset voltage(0-250mv, step 2, default value 100,which means that the soldering iron head maintains the output voltage inherent to the room temperature op amp, if you do not measure, please keep the default value p03-increase the ttemperature, adjust the temperature ,30-50 ℃ )
P03
if you do not measure, please keep the default value p03-increase the ttemperature, adjust the temperature ,30-50 ℃ )
P04
p04-temperature adjustment step(0,1,2,5,10 degrees optional, 0 can lock the soldering iron temperature)
P05
p05-sleep time(0-60 minutes,step 1 is 0, the sleep function is disabled)
P06
p06-shutdown time(0-180 minutes, step 1 at 0-30,step 10at 30-180, disable function when 0)
P07
p07-temperature correction(-30+ 30 degrees,step 1)(because the ntc resistor is in the chassis, the soldering station will cause the detacted ntc temperature to be higher than the room temperature, resulting in high compensation of the cold junction of the thermocouple, and the temperature of the soldering iron is not accureate. it can be corrected with this parameter. fro example ,if the detected soldering iron temperature is 20 degrees higher than the actual value,set this paramter to 20)
P08
po8-wake-up mode (0,1,0 means that the encoder can be rotated in the shutdown mdoe and the handle can be awakened by the vibration handle. fro 1, only the rotary encoder can wake up )
P09
p09-temperatue plus strength(llight click on the encoder to error to enter the temperature for the shdden need to weld the solder joint)
P-10
p-10 temperature enhancement time (enhanced time...)
P-11
p-11 buzzer switch(o means off 1 means on)
NOTE:
Iron tip do not work continuously high temperature, high temperature work is easy to damage the tip! Ordinary solder melting point is 183°C, lead-free solder melting point is 227°C, usually the welding temperature is 300-380°C, 380°C is the temperature of the dividing line, higher than 380°C, iron head oxidation and loss is extremely fast, seriously affect the heating core life The Higher than 380°C temperature display will be beating, the higher the temperature, the greater the beating!Recommended in the 300-380°C for welding work, most of the work can be carried out, the temperature beating is normal, does not affect the use! The soldering iron used in this soldering station is a brand new soldering iron tip. Due to the unstable resistance of the new soldering iron tip, the temperature will jump or ERROR, which is normal. After several times of use, the stability will gradually stabilize. If you mind, please do not buy.
В обзоре абсолютно непонятно как настроить станцию