3D Printed Headlight Ducts from EFB Motorsports - EF Honda Civic
Вставка
- Опубліковано 23 лип 2021
- Find product here - www.efbmotorsports.com/
Cameras used in this video
My GoPro - amzn.to/2YQ3OGZ
My Mirrorless Camera - amzn.to/2HzzFFT
Send me stuff here!
Jon Widmer
PO Box 13594
El Paso, TX 79913
/ garagebuilthondas
Thanks for watching!
Disclaimer
"Due to factors beyond the control of Garage Built Hondas, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Garage Built Hondas assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair videos. Due to factors beyond the control of Garage Built Hondas, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again, any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Garage Built Hondas."
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll potentially receive a small commission at no cost to you. This will help support the channel and allows us to continue to make videos like this. Thank you for you support! - Авто та транспорт
Thanks Jon for taking the time to make a video on our first batch of products! If you guys have any questions, come join the discussion over at our IG page. We're doing a 1,000 follower giveaway! instagram.com/efb_motorsports
Any plans for other chassis?
@@TheXXXskater1 we do plan to make parts for other vehicles in the future, but no specific plans yet. The more feedback we get from what the community would like to see the better!
@@TheXXXskater1 We also offer custom part development, dm us your idea. Depending on the scope of the project, we may be able to help.
Can you make the headlight inlet block off plate? just in case it happens to rain while we're driving. we can just stop and put a block off plate where the intake filter is?
@@olderrol1968 We've got a prototype that slips over the beaded outlet adapter. Been so busy stocking up inventory lately we haven't had a chance to make one final revision necessary before we test it and make it available.
Love how the whole thing lights up. I can't imagine if those existed back in the 90s. It's awesome seeing so much love for older chassis still!
Were a big fan of the translucent material as well!
I am in love with that fiber optic effect for the housings! So cool!
Thank you! So are we!
Bruuuuh! Those came out sick!
You should cop the black ones homie!!
Wish they had these back in the day
Same.
Those headlights are so sick…👍🏽👍🏽
Agree!!
Just the headlights alone make me want to buy an ef. Looks so damn good!
Headlights look badass!
I might be getting a set for my rex!
Right on!
Those do look badass.
Oh HOT DAMN!!! Looks legit AF💯👌👌👌
Thanks for the kind words!
Definitely buying a pair for my car , I wish they sold them as a bundle deal I’d you bought both headlights! So cool!
They do. It's less expensive to buy the pair.
How do you find that option I have a pair in my cart ready for checkout and i calculated it, it’s not cheaper for a pair, atleast on my screen
I thought it showed automatically. If not contact the seller.
Sick parts! Looks really good
I'm sold, take my money🤑. These are great!!
Thank you for the kind words!
Those headlights are nice, good light output
Wow just wow
👍
This is so innovative. I wish stuff like this was made for my chassis!
Looks good Jon.👍🏻
Beautiful i love them, definitely getting these in the near future.
What's up Jon🤛🏾Might have to look into those plastic pieces for my CRX 👍🏾
👍
Very nice. Headlights look excellent. I'll be picking up a set of the cowl hardware.
Thanks for the kind words James. We look forward to your business!
Really cool pieces for the EF!!
👍
Hella cool headlights!!
We need some 3D printed door moldings and side-moldings, now! That would be awesome! I realize they are probably too long to print but it is good to dream.
That'd be sweet
The lower door trim molding? Or the belt molding along the window?
Both!
What up fam!!! Bro you at 72k subs! Congrats man omg. I've been so busy I missed out on a lot of videos. Lol
Man, I saw the headlights on Instagram, but you're really making me want a set for my hatch. lol Now he just needs to come out with a matching set of taillights!
He should make some corner lights, I don't have any Civics anymore but those wagon corners are hard to find.
Cool stuff!
They look sickAF!
Glad you like them!
Oh boy these are fire 🤦🏻♂️🔥
👍
That's looks so awesome bro frfr I'm just dreaming on what my k24 ek going to look like when I get it done
Okay. This is amazing 🤩
👍
Very cool!
Cool stuff. I wish I knew how to do that kinda 3d modeling stuff. I have plenty of ideas for the cars i am into
Wow those are awesome
Fit mint is spot on from what I can tell on video
Yup! On our car when we measured the panel gaps they were the same as the oem headlight!
He put a lot of details into these products
Thanks Corey! We wouldn't want to offer anything we wouldn't rock on our personal cars!
nice product
Would love to rip that ef on some back rds would be so much fun! Looking good brotha 🤙
Thanks!
I want these headlights but they are so expensive I wouldn't mind paying 250$ for 2 but for one idk.
Something different but its cool 👍👍
Glad you like it!
I gotta get me a set ASAP
🙏
We need an update video to see how these held up
They're doing great, they've actually been painted black and transplanted to my friends crx.
Man I love to style of the headlights, I wish he would take it a step further and make one piece headlights with the corners.
We like the look of the stock corner lights. Plus there isn't really going to be a functional benefit to doing so.
I like the setup but you need to feed that air somewhere. Simply letting the air under hood can hurt radiator performance. You need low pressure behind the radiator/inter-cooler for best cooling performance.
He's aware, you'll see what he did in an upcoming video
That’s all badass I started following him I will be looking into those headlights that would be great for my built civic and I like the air vent gage pods I would rather have that also
those arent even available on the website tho
@@TheShangralaaaa17 It will be soon! We wanted to let Jon test them out and see if there were any issues. He seems to be happy with them so we will start building up inventory this week!
Always a good video. I wish you my neighbor lol
Please tell me he makes them for quad light integras!!! Super dope!
Thanks for sharing…now I have to decide white or black for my blue CRX…it’s the same color as your door. Possibly paint match option for aesthetics…hmmmm.
Painting them would look great! We've been wanting to try clear coating the translucent duct on our personal car, think that would look awesome!
Beasty!
Ok i'm quite the cynic with most things, but those lamps are seriously impressive. =]
Thank you!
Next should be hood louvers or vents, you can even put hood risers. Air enters the front of the car, the problems cars face with excessive heat is heat extraction.. you’ll want to pull the heat out now.
Im still waiting for my naca duct to come in, thinking of installing it on the hood of the dc5, it works by guiding air in, and if you run it backwards it works like a venturi effect by sucking air out with vacuum. Actually you should look into NACA ducts 🤔🤔
Used some hood vents today. Kind of a funny outcome, you'll have to see the video in a few weeks.
Hood risers actually hurt the effectiveness of the radiator. Plenty of articles on it. Plus I don't like how hood risers look at all. Unless I had an engine that required some risers I wouldn't personally put them on my car.
@@GarageBuiltHondas nice man, can’t wait to see! I’ve seen mixed results on hood risers, I’ve seen people get lower temps in the engine bay with them, but I don’t know if it effected radiator flow, I don’t know if it’s much of a negative effect it could be since the radiator is all the way up front and seems a large amount of air..
Where are you placing the vents? I think it’ll be best for a large vent front and centered over the exhaust manifold, the heat behind the radiator will exit from there, and also in the rear corners of the hood by the hood hinges, it’ll get rid of the pressure in those areas and allow a stream of air for the intake too
Yes, I added 2 small vents which vented the area between the radiator and engine. That's where it's most effective as the air that comes through the radiator hits the engine and normally hits the undersides of the hood. Venting in that area allows that air to travel through the radiator, up against the motor and directly out the top of the hood not only increasing the radiators effectiveness but also removing the hot air as well.
I used some cheap ebay hood vents. Although they worked well, the end result is pretty funny.
I been looking at these i fallow him. I'm just waiting for final product to order them into canada
👍
They are finalized, shipping to canada is available ;)
Reproduces the rear speaker pods. O.e.m. are hard to find.
Sickkkkkk
👍
I was excited for these to come out but they are waaay out my price range! Good luck efb
Says the guy who spent $3400 on a b16 swap. 😂
@@GarageBuiltHondas that was money well spent 😂😂 these engine swaps are getting impossible to find low mileage
@@crxdrew4974 it's true, and yours hauls ass. I'm working on the video now. It should be out in 2 Saturdays.
@@GarageBuiltHondas I’m gonna buy a b20 for that same price!
@@GarageBuiltHondas heck ya can’t wait!
Would love something like this for an Integra
Damn I need those cowl panel clips for my DA.
Pretty sure they will fit, but its not confirmed yet. Message us if you are interested in a set for your DA, we can offer a discount if you confirm fitment for us.
@@efbmotorsports2047 will they fit EGs?
Pretty sure there are ones on thingiverse that work.
@@nobodynoone2500 those are just oem replica caps. Completely different than our product :p
Those headlights look fokin bitchin!! 👌pardon my french
Thank you!
Will cutting vents on the hood over the exhaust manifold help disperse heat quicker and help areo letting trapped engine air vent helping eliminate lift
Definitely
Nice crx. I live in el paso and I can't find a crx. I had one for 10 years and regret selling it
I've seen maybe 2-4 for sale over the last year on different places. Are you ready with cash in hand? They usually don't stay for sale long.
👍🏻
Man I wish I could paint that little ef for you
I wish! You're probably far from me?
@@GarageBuiltHondas I’m guessing so I’m in Cali, not sure where you are at
Yeah, just a bit. I'm in Texas.
@@GarageBuiltHondas darn if it was Arizona or Nevada I would have made the trip out there
I need this for my b13
We got you!
I like the translucent effect, is it the same way with the black color?
Same design in black, more pics are on our IG and website linked in the description!
Hey Jon whatever happened to the other track car with the B20? And I have another EF question. My d series is misfiring under load. It idles fine, sounds smooth, fires right up but when I take it around the block it misfires as soon as I give it some gas. Everything in the ignition system is brand new, even swapped the other distributor off my 89 5speed and no change. I'm assuming it could be timing is off, is there anything else that could cause that problem?
👀🔥🔥
Could you do a light range comparison to stock lights?
That's a great idea, well try and post on our IG in the upcoming days! Im currently running a single bulb ZC headlight on the driver side and the duct on the passenger side. I'm not sure most people would notice much difference while driving until pulling up right behind another car at a stoplight.
@@efbmotorsports2047 You could drive up to a wall and see a comparison on the light beam range and width.
Great video ! Any suggestions where I can purchase headlights side lamp clips for my 1990 Honda crx he , also looking for the front bumper I see one on eBay but not sure if it’s direct fit ?
Cheers from California
Thanks 🙏
Look at OEM Honda parts websites online. I believe they sell the clips still. All 2nd gen crx bumpers are interchangeable.
@@GarageBuiltHondas All USDM crx bumpers that is. ;)
Headlamp model crx & ex 88 same or different?? Please share guys..tQ..From malaysia
Yes
Did you need to do new wiring to be able to use projectors with those headlights.
If you buy the assembled headlight, it is completely plug and play. If you opt for the kit, it has all the components necessary for a plug and play headlight, but you wire it yourself. No modification to your stock headlight harness is necessary.
@@efbmotorsports2047 thnx
Where can i order those headlights i love them
Our website! Link is in the description of the video!
Do you have a video about putting a rear sway bar on an ef? I swear i saw one and i lost it.
What brand bar?
Garage Built Hondas it might have been ASR
ua-cam.com/video/PYMhoqVVUys/v-deo.html
👍👍👍🌵🌵🌵
Whens the EF Kswap step by step how to releasing Jon?😏
At my rate, probably never. 😥
When i see other CRX’s it makes me realize how unmolested mine is
I got one of those too..👍
Keep it that way. Mine is cool, but (mostly) stock was better.
doo these fit the wagon?
Yes
Think it fits crx 88
Yes
gotta be careful pressurizing behind your radiator. your intake might be getting cooler air, but it might be lowering the efficiency of your radiator.
👍
Can the headlights fit on 89 honda civic sedan too just asking
4th gen USDM civics and 2nd gen USDM CRX headlights are all interchangeable, so yes.
@@efbmotorsports2047 alright thanks
Would these fit a crx??? I need some for my track car
Yes
Yes, all USDM 88-91 Civic/CRX headlights are interchangeable
Would those headlight fit the wagon?
Yes
@@GarageBuiltHondas amazing thanks im gonna put my order in.
both of these lights cost as much as my whole engine tho
Ask him too make 1 pice headlights for 1990 Acura integras
Hoe much are they?
www.efbmotorsports.com/product/usdm-88-91-civic-headlight-intake-duct-kit
If they had those for an EG though😉
Can someone make me a rear HFP rear lip with a 3D printer lol
DM us on instagram or email us if you're interested in custom work! Depending on the scope and budget of the project, we might be able to help.
Do you eat ice cream sandwiches ?
Only if its coach gregs anabolic ice cream!
@@efbmotorsports2047 I haven't had those I'm unfortunately not an American yet I live in chinada up north from you guys lol
They look ill.
I need help any way you can contact me
What do you need?