Hello, the Canon 5235 copier indicates that there is a paper jam. The heater has been replaced and the same problem. The outer door has also been replaced and the same problem. Is it possible that the problem is in the power supply?
Sir I have canon printer. Output voltage on power supply is mentioned as 24V. But when checked with multimeter, it is showing 28.1V. Is power supply ok or damaged? Although printer is turning on. Printer's scanner motor is rotating fast in both forward and backward direction and then stopping suddenly. And also cis light is not turning on. Is high voltage a problem for both above issues?
Supply me 2.5 v aa rahe h but card lgane pr b 24 volt nahi h rahe logic card change kr ke dekh liya supply change krne pr printer ready ho rh h ab purani supply ko kese thik kare
Resp Sir! Same Canon Board Was K4005 FET Changed Sir and near 22G Ohms Resistor and near the Big Capacitor Resistor was Burned Sir. That Bellow 100Ohms Resistors 50Ohms 22Ohms was Installed but not Suported Sir. Same placed Jumper Suitable or not Sir. Please Advise Sir. -- ChinnaRao Paderu Visakhapatnam Andhrapradesh
Resp Sir! Thank U Sir and not short the Primary Section Any Component Not Beep Sound Sir and Secondary Section also Same Sir. -- ChinnaRao Paderu Visakhapatnam Dist Andhrapradesh
Resp Sir! Canon MF244DW Printer Power Supply DC 2.5V Ok But not Turned On Sir. Where the Problem Sir. Please Advise Sir. -- ChinnaRao Paderu Andhrapradesh
Resp Sir! Same PCB output 3.7V Suitable Sir or Not Suitable Sir. 10 Ohm Resistor Replaced at Near the Big Capacitor and 1 Ohm Resistor was Replaced the FET Sir. Please Advise Sir. -- ChinnaRao, Paderu, Visakhapatnam Dist, Andhrapradesh.
Resp Sir! Canon MF244wd Printer Power Supply Series Lamp was On Sir all are LDRs, Capacitors, Bridge Rectify Diode, 3Pin Diode all are No Beep and No Values OK Sir. New FET was Changed Sir. 22G Ohm Resistor and 24G Ohm Resistor was Burned Sir (this Resistors 0.3 Values and Beep Sir) Where the Propblem Sir. Please Sir. I am Waiting Sir. -- ChinnaRao, Paderu, Visakhapatnam Dist, Andhrapradesh.
Thanks please. That mosfet on the heat sink near a big capacitor heated up and I can't understand it to get its replacement. Could you please help
Hello, the Canon 5235 copier indicates that there is a paper jam. The heater has been replaced and the same problem. The outer door has also been replaced and the same problem. Is it possible that the problem is in the power supply?
Sir......nice information thank you
Sir I have canon printer. Output voltage on power supply is mentioned as 24V. But when checked with multimeter, it is showing 28.1V. Is power supply ok or damaged?
Although printer is turning on.
Printer's scanner motor is rotating fast in both forward and backward direction and then stopping suddenly. And also cis light is not turning on. Is high voltage a problem for both above issues?
Sir if current is not showing in the printer. When I have opened this priter. What type of problems can be happened.
Most of the cases fuse MOSFET both are faulty
sir , White page ki problem aarahi hai kay solution hoga pls batayeye
Cartege new dalne ke baad bhi print black aata hai... supply repir karne se phle ....earthing plate ko chrak jarur karle...
Depends upon the fault
Hai..sir ..Canon mf4820d printer board automatic restarting problem & relay continuously making tik tik sound ..please help me with the solution
Supply me 2.5 v aa rahe h but card lgane pr b 24 volt nahi h rahe logic card change kr ke dekh liya supply change krne pr printer ready ho rh h ab purani supply ko kese thik kare
Model number?
@@trcteck canon mf3010
Resp Sir! Same Canon Board Was K4005 FET Changed Sir and near 22G Ohms Resistor and near the Big Capacitor Resistor was Burned Sir. That Bellow 100Ohms Resistors 50Ohms 22Ohms was Installed but not Suported Sir. Same placed Jumper Suitable or not Sir. Please Advise Sir. -- ChinnaRao Paderu Visakhapatnam Andhrapradesh
Check primary section short component also check secondary section diode
Resp Sir! Thank U Sir and not short the Primary Section Any Component Not Beep Sound Sir and Secondary Section also Same Sir. -- ChinnaRao Paderu Visakhapatnam Dist Andhrapradesh
Kindly share your ps card video on my Instagram id trctech
@@trcteck Resp Sir! Thank Ur. OK
Most welcome
Good
Resp Sir! Canon MF244DW Printer Power Supply DC 2.5V Ok But not Turned On Sir. Where the Problem Sir. Please Advise Sir. -- ChinnaRao Paderu Andhrapradesh
Make sure it is ok or not then try
😊
❤
Sir printer on nehi hu raha he😢problem kaise solve kare
Resp Sir! Same PCB output 3.7V Suitable Sir or Not Suitable Sir. 10 Ohm Resistor Replaced at Near the Big Capacitor and 1 Ohm Resistor was Replaced the FET Sir. Please Advise Sir. -- ChinnaRao, Paderu, Visakhapatnam Dist, Andhrapradesh.
Explain your problem with printer model no
Sir Canon MF244WD Printer Scaner Sir. -- ChinnaRao
Replace logic card
Resp Sir! Thak U Sir.
Welcome
Resp Sir! Canon MF244wd Printer Power Supply Series Lamp was On Sir all are LDRs, Capacitors, Bridge Rectify Diode, 3Pin Diode all are No Beep and No Values OK Sir. New FET was Changed Sir. 22G Ohm Resistor and 24G Ohm Resistor was Burned Sir (this Resistors 0.3 Values and Beep Sir) Where the Propblem Sir. Please Sir. I am Waiting Sir. -- ChinnaRao, Paderu, Visakhapatnam Dist, Andhrapradesh.
printer display probmel
Sir Printer on ho kar band ho jata 3-4 second ke baad kya reason ho sakta hai
Check fuser wala jha connector lga hota 8pm ki 3 leg ka MOSFET lga hota hai check kro
@@trcteck fuse check karna hai power supply card mai ya mosfet??
Both
Badavala Capasitor voltage is DC or Ac?
Dc
@@trcteck kithna volt ayega sir?
Power supply er r216 resistance colour code or value kaya hua
Pls help me sir
Test according to colour code
Pls help me sir ...r216 resistence burning and printer have no power
Sir u not help me..pls r216 resistance ka value or color bolie....cause my power supply board me r216 resistance burning
Bhai mere Instagram par resistance ka photo bhej do
instagram.com/trctech
Sir board ka schematic diagram kaha se milega?
Part no?
LBP 2900B
Sir Thanks u
Solution kya he
Always burn fuse.....pls help
MOSFET and bridge change kro
Sir tray continuosly chll.rhi hai solution plz
Laser scanner change kro
Canon mf 4820 me blank print aa raha he
Replace power supply
❤