DIY DC Mini Grinder With Speed Controller

Make your own DC mini grinder with speed Controller
parts:
1. 775 DC motor
2. JTO Mini Drill Chuck + 5mm Arbor shaft connector
3. 20A PWM DC Speed Controller
4. 1.5 Inch PVC Pipe
5. Pipe Connection 0.5 Inch to 1.25 Inch
6. PVC Cover 1.25 Inch
7. 6 Pin On-Off-On Switch
8. 2 Pin CB Socket
Visit the Creatividea Channel
See other videos here:
/ @creatividea
Don't forget to LIKE, SUBSCRIBE, and provide suggestions and comments
Thank you

[@ОлегКоробкин-у7е]

с таким биением шпинделя, просто выкиньте этот девайс!

[@ВлаСт-и6д]

И вся стружка летит в движок. :-)))

[@narpat007]

nice but this motor on load draws as much as 20-30Ams at 12V, I had used that motor in 2 mt. wing span RC Plane, long long back and it was drawing 26Amp at 3S (11.1V) LiPo battery on takeoff on 7x5 prop
It appears that your wiring can not take more than 5Amp, so it will eventually burn on load. You are very creative, I appreciate that a lot but also focus on enhancing your skills in electronics / electricals

[@handle5557]

Is it true up to 20Amps? What is the speed. Has the motorbike been modified? Because here the motor without load is only around less than 1.5Amps

[@suthinsorakul2137]

ที่ประเทศไทยมีขายหรือเปล่าครับจะสั่งซื้อได้ที่ไหนครับ

[@SC.243k]

Very very beautiful, thanks for sharing my friend 👍

[@creatividea]

Thanks my friend 🙏🙏🙏

[@ЖеняМаланчук-г5о]

Мне нравится ваши работы.😃👍👍👍

[@user-vv8ec1en8i]

Нихера себе там биение башки в начале видео.

[@Seniman-45]

Bang buat amplifier dari transistor tip41 ya bang tapi transistornya 4

[@ф5ф5ф5ф5ф5ффф]

в руки тебе насрать за такую балансировку она тебе руки по отрывает

[@rubadi2777]

bang , untuk mengatur kecepatan dinamo enakan pake speed controller / power suplai ajustable? 🙏

[@creatividea]

speed controller

[@sldineshbro]

Excellent 🏵️ thanks you 👌

[@CreativeExtra]

I make videos like this please watch

[@ZenicHo-tf6ch]

Di jual kah mas?

[@MrBobash]

You have to wear motircycle helmet to be protected from such wobling chuck.

[@rianharis5924]

Info link pembelian alatnya mas barang kali dijual😅

[@fayyazbahrami296]

your chuck wobbles too much , motor without bushing has less power and efficient

[@tonyfirdausbuanajaya]

Coba batre cordless ka 🙏🙏, pengen coba bikin

[@hasantamer9199]

elinize sağlık hocam

[@creatividea]

Teşekkürler 🙏🙏🙏

[@valtersouzaribeiro761]

Bom dia parabens muito bom

[@angelandcrafts]

keren mas....bisa di coba juga ni

[@creatividea]

Silahkan 👍

[@gunawangunawan2867]

Karena GK punya adaptor variabel 😅

[@phantomphantom2006]

центровка у патрона моё почтение)пол дня поработаеш и руки будут как у алканавта,думаю автор немало с алика заказывает...но что не сделаеш для контента,вот и получилось изделие сиё для пыток и удовольствий(нужное подчеркнуть)

[@tranthaibao7932]

cho em hỏi anh có làm bán không ạ

[@SamsulBahri-fe3ky]

Suplay berapa volt mas?

[@creatividea]

12 sampai 24 volt

[@adypoernama5127]

Mas sock depan mksdnya ½ inch x 1¼ inch kah???

[@riensilaban1760]

kira-kira lebih kuat mana ya dari mini die grinder..?

[@Glenn_ID]

Bang jual yang udah jadi ga?

[@creatividea]

belum, mungkin kedepannya

[@MakKimak-r8d]

Chuck nya goyang gimna ya cara ngatasi nya,udah di getok2 sampe blance pas pasang mata bor malah goyang lagi😢

[@Y.U.Y_1575]

Seperti nya konektor JT0 yg ke as 5mm kendala sama, konektor nya yg geol alias tidak center.

[@WalArtTech]

Mantap bos..alat nya terima kasih sharing nya..semoga berkah ilmunya ..izin yah..minta ilmunya nih mau cobain bikin sendiri..kebtulan sy lagi butuh alat bor mini dan gerinda mini..seperti ini...

[@creatividea]

silahkan, selamat mencoba

[@if_coolteknolob3423]

Bang, mata bor untuk bolongin kotak di pvc itu type apa ?

[@Hayantoo]

kalau pakaii adaptor Ac 110-240V kemudian sambung kan ke Dimmer Regulator Adjustable PWM DC 12-40V 10A 400W dan pakaii dinamo 775 ,,,Apa bisaa bangg?

[@creatividea]

disarankan maksimal sampai 24V PWMnya, kalau sampai 40V bisa rusak dinamonya

[@Hayantoo]

@@creatividea tapii soallnya adaptor nya kecill bang bulan yang besarr ,cuma kecill ces²an Hp bang.

[@creatividea]

dinamo 775 bekerja normal pada rating tegangan 12V sampai 24V. untuk PSU/adaptornya harus yang bisa supply arus sampe 10A. ga bisa pake casan HP.@@Hayantoo

[@gunawangunawan2867]

Bang pengatur kecepatan nya pake yg Gerinda buatan itu bisa kah

[@creatividea]

Bisa, pakai saklar bor cordless

[@vitthalnikam4917]

What kind of paper you used for decorating the drill machine.

[@creatividea]

scotlite sticker

[@EnigmaX_ID]

Bang ada tutorial membuat variable power supply yang di vidio

[@creatividea]

ada di cek aja ide kreatif dari bekas power supply komputer

[@sufiyankhan-ts5hm]

1,, number bro

[@Seniman-45]

Mantap bang 👍👍👍👍👍👍

[@creatividea]

Makasih...🙏🙏🙏

[@CreativeExtra]

I make videos like this please watch

[@Y.U.Y_1575]

Bang chuck nya geol banget ya, itu bisa cepat merusak bearing dinamonya. Aku juga beli konektor chuck jto sama geol parah.

[@creatividea]

iya geol kalo di RPM rendah, kalo RPM tinggi dia stabil

[@sahadarizal347]

@sepsopandi8575 itu karna lu nggetok konektor ke chuck jto nya asal2 an,, gua nggetok konektor ke jto nya gua presisi kan rpm rendah gak geol tuh aman² aja udah 3 tahun ini cuma ganti dinamo nya aja😎

[@Y.U.Y_1575]

​@@sahadarizal347iyakah ? Punya gua mah konektornya juga udah geol bang, mau di presisi kan kek ginana juga tetep ga bisa.

[@ВалерийБеликов-щ1н]

The Cool Cool Cool...

[@Keizzn]

Ada skema nya om?

[@sardjonomudio8688]

saya pemula kira2 bisa tidak ya membuatnya?

[@creatividea]

Tidak ada kata tidak bisa, pasti bisa kalo mau.

[@bhaskarpatil4976]

Nice osam educational etc.

[@CreativeExtra]

I have uploaded a new video please watch

[@elecktrosedehana6290]

👍👍👍👍👍

[@minhthienle4458]

Dream ! Ok!

[@CreativeExtra]

I have uploaded a new video please watch

[@enrikcarlos6248]

Wahhh mantap polll mas👍

[@CreativeExtra]

New video is coming please watch

[@Techno0070]

Very INOVATIVE and creative🔥🔥🔥

[@CreativeExtra]

New video is coming please watch

[@Pata-h5t]

Respect!Super!