Yes! But then he couldn't make this video showing off his unnecessary, overly complicated, 6 cuts too many, long way round, special "trick" that we dont know about. 🙄 Guaranteed this guy tacks all the way around his joints 👍
@@tepidbudgiehe didn't create a stronger joint you are referring to load bearing wood structures completely different than some non load bearing welded tubing. A fully welded 45° would be just as strong and much faster then what he just did he thought he was pulling a big brain move but he actually just worked harder not smarter.
@@chadklaren9537 He did create a stronger joint, the work is load bearing to a degree since it being a handrail. Yes your method is faster, but not stronger.
Cutting the vertical post to the angle would have easier, faster, and not left a weld on top of the rail, while still not needing to weld an end cap…so NOT excellent.
he just needs a combination square, but he has to wait for us to throw a working one out then the trash to get shipped to whatever country he is in.. so maybe in a future video lol
Я тут видео видел, там мужик делал примерно то же самое, но через базон Хиггса, с использованием теории вероятности и потом рассчитал угол через уравнения вископулярности Гейенмахера.
@@АлексейТурковский-в9хтогда под тем углом под которым подходят. В данном конкретном случае 45. А если умственно отсталый человек то можно и этим способом воспользоваться конечно. Без обид. Я против вас ничего не имею, просто ты таким родился
No se puede hacer ese corte a 45º en el tubo vertical por una cuestión de geometría. Analice la situación y verá que lo que se hizo en el video es correcto
@@marcelopose😂😂 bro, please see the vertical pipe's bottom line and after fixing the tube see the scale putting upon the pipe in the last of video. If u cut the vertical in 45°, work is simple & u can avoid two welded joints.
Essa é a lógica, fica menos trabalhoso e com um acabamento mais limpo... Mas, talvez esse tipo de emenda seja útil em uma continuação ou simplesmente é uma ideia pra gerar engajamento e obter visualizações kkkk
@@brianbeach9472 lol, no? If the railing was just a cap, it would be much weaker than this. It sounds like you've never actually done much railing installation if you think a railing attacked to ends of posts are secure.
@@JgHaverty no dude, the top rail becomes the cover that you weld on. Everything is contained and nothing needs to be notched or ground back down. Economy of action AND better end result.
Most people commenting are talking about being efficient and not wasting their own time and energy. It looks good in an art project or some really specific design intentions maybe but in every other circumstances it's just wrong
@@yofedstyhrega4594it's not wrong, it's just that there are better and faster ways to get the same result. Now if you are experienced you don't need a ruler.
No se puede hacer ese corte de 45º en el hierro vertical por una cuestión de geometría. Analice la situación y verá que lo que se hizo en el video es correcto.
Yes you are. You realize they are going to be welded after that? This man is a welder/fabricator. Those little pen marks aren't going to be there for long.
Person preference. Most of us are the boss so there's no "right" way as long as you get the desired result at the end. I stopped doing checks when I moved to finish carpentry, can't mark the final product
My man I have used a lot of squares in my day of 50 years I have never seen one used with that kind of precision then I watched your video like 10 times and I still am not sure if I understand but I think I got it .that's some good stuff
Observation is necessary for new and different ways of doing things, a lot of people including myself think about an idea after seeing others mistakes and and challenges ... i can appreciate different ways expressed of doing this cut or joint....not sure if this was a mistake, but this helps if you've made a mistake and or short on material or have reached too far in a project to just change a piece... i can appreciate the value of different routes of fixing a mistake made ... thanks
Well that depends, because if the stairs continue then yes, you can use that method, but if the step were the post is on has like this weird distance from the next step, you may want to use the first method to like give continuation to the way the steps go up.
This is not a quiker type of application its about skill and joinery . I am a carpenter. Finish and trim is my specialty. I can appreciate the precision and the stability with the finger on the edge it stabilizes the joint . A generic person like sone of the commentators would not nitice or appreciate that lol
Можно было центральный элемент под нужным углом отрезать. А если нужно было крепости конструкции добавить, то следует более сложный замок делать - для левого элемента тоже
Easier to hold the higher rail in line as it will eventually be set at, and then trace the post onto it. Same effect but without so much water time and extra steps. Simplicity is best.
Wouldn't have been simpler to cut the post at an angle?
Yes! But then he couldn't make this video showing off his unnecessary, overly complicated, 6 cuts too many, long way round, special "trick" that we dont know about. 🙄 Guaranteed this guy tacks all the way around his joints 👍
@@Unforgettable_Name😂
Simpler... Yes, but his way produced a stronger joint. Akin to a birdsmouth on a rafter. More able to support vertical and horizontal load.
@@tepidbudgiehe didn't create a stronger joint you are referring to load bearing wood structures completely different than some non load bearing welded tubing. A fully welded 45° would be just as strong and much faster then what he just did he thought he was pulling a big brain move but he actually just worked harder not smarter.
@@chadklaren9537 He did create a stronger joint, the work is load bearing to a degree since it being a handrail. Yes your method is faster, but not stronger.
Bevel the post, single continuous hand rail. K.I.S.S.
Was going to say this exact thing. Only logical application for this would be a splice.
Too easy. Must be a government job...
Love it. Especially w this person's angle grinder skills, would have been a since.
Yeah, I thought they could be a not simple way to achieve this result. 😂
Genius!
Not many people would use this "trick" even if they knew about it. Waaay more complicated than it needs to be
I wouldn't use that "trick" if I was trying to terminate a railing at that post..... just too time consuming in a production environment.
A 2×1/2 ×3/16 SQ TUBING
IMAGINE IF IT WAS A 9×4×3/8.
AND DROPPED THE MEASUREMENT AND CAME SHORT DANG !
@@CICWSfirearmsYop slap it cut it and weld it , field welders , no b.s .ing around ,
It would be faster to cut the lower column at 45 degrees
45 plus 45 is 90 the angle of this is unknown, normally I'm the first to rip on these videos, but for something done outside this works well
❤
I was just going to say that!
👍
Sí, pero entonces ya no es tan complicado
The column is hollow.
Can’t you just cut the vertical at an angle and use a long section for the rail? It would be a LOT less work.
This channel is all about giving the most time wasting advice
А где он тогда будет так многозначительно махать пальчиком???!! 🤔🤔😜😜😜🤟
Shhh, that would require common sense. Which is rare
Но мы же не ищем лёгких путей! ☝️🧐
А как тогда подписоту с лайками собирать?
А впрочем, автор молодец, работает как фильтр для тупых.
Excellent. Fully covered without having to weld end covers. I like the style, too.
Cutting the vertical post to the angle would have easier, faster, and not left a weld on top of the rail, while still not needing to weld an end cap…so NOT excellent.
Is this man really out here sharpie'ing his square for every cut?
It comes off easy
he just needs a combination square, but he has to wait for us to throw a working one out then the trash to get shipped to whatever country he is in.. so maybe in a future video lol
It's to show beginners how to do it...hope you learned something today.
@@pythonpeteto show beginners the hardest nonsensical way to do something?
@KZ-yy9pm
....yeh, I'm mad I didn't think of this hack also when you're winging it for a home project, and you just don't have the length.
Great. Now it’s too short.
weld the piece you cut off back onto the other end lol
@@bmxscapechocolate bar math 😂
It was pre-calculated into the cut budd
@@Diogo7442 Wow dude! Ever heard of a joke?
@ckane510 where's the joke. I don't see anyone laughing
Автор всё-таки нашёл, этот самый сложный способ
Человеку просто нехуй делать заниматься такой ебаниной :)
Я тут видео видел, там мужик делал примерно то же самое, но через базон Хиггса, с использованием теории вероятности и потом рассчитал угол через уравнения вископулярности Гейенмахера.
Надо стойку обрезать под 45 градусов и приварь к ней
*Yes, that was my first thinking 😅*
*He build first the House, after the Basement 😁*
С языка снял.
Вы что, тогда видосика не будет
А если профиля к стойке не под 45 подходят, как тогда ?
@@АлексейТурковский-в9хтогда под тем углом под которым подходят. В данном конкретном случае 45. А если умственно отсталый человек то можно и этим способом воспользоваться конечно. Без обид. Я против вас ничего не имею, просто ты таким родился
Cut the vertical tube, & fix the single tube above it, simple.
True
No se puede hacer ese corte a 45º en el tubo vertical por una cuestión de geometría. Analice la situación y verá que lo que se hizo en el video es correcto
@@marcelopose😂😂 bro, please see the vertical pipe's bottom line and after fixing the tube see the scale putting upon the pipe in the last of video. If u cut the vertical in 45°, work is simple & u can avoid two welded joints.
Стойку отреж под углом нужным, а сверху цельную трубу😊
Технически так шов может и будет крепче, но много лишних измерений, достаточно одного
Legal!!!
Mas porque não cortar o pé direito no ângulo necessário assim deixando o corrimão contínuo, o que geraria economia de tempo e material?
Essa é a lógica, fica menos trabalhoso e com um acabamento mais limpo... Mas, talvez esse tipo de emenda seja útil em uma continuação ou simplesmente é uma ideia pra gerar engajamento e obter visualizações kkkk
Не понял только,почему сам столб наискосок не отрезать🤔
Цифры запомнить не может, маркиром метит, а тут аж на искосох трубу отрезать надо...
Соскользнёт 😂
И о чем тогда видосик снимать? 😏
мы легких путей не ищем!
Could also keep the rail as one piece and cut the post to the angle and skip all that nonsense.
Obviamente así es pasar el pasamanos en una sola pieza y hacerle el corte al parante y no hacer tantos cálculos de geometría 😂
Amen. And the structural integrity would have been much greater done in that way. The majority of these videos are so ridiculous
@@brianbeach9472 lol, no?
If the railing was just a cap, it would be much weaker than this. It sounds like you've never actually done much railing installation if you think a railing attacked to ends of posts are secure.
Não faz nenhum corte na peça inclinada e corte em 45º a peça peça vertical 👍🏽
Pero queda el hueco arriba
Why not just cut the bottom sq tubing at an angle and leave top sq tubing intact.
Paid by the hour, not the footage.
That would feel the best to the hands sliding over the rail.
So NO. 😂
Because youd have to then go back and weld a cover for the open tube you left... this cut literally took seconds to do, why complain?
@@JgHaverty no dude, the top rail becomes the cover that you weld on. Everything is contained and nothing needs to be notched or ground back down. Economy of action AND better end result.
@@thelasttimeitried I'm gonna let you think this through, reevaluate your statement and figure out why you're... Wrong lol. This isn't rocket science
I don't care what all of the others have written about how you should do the job,as for me I think you did a nice job.
Ur probably haveing No clue of it
Most people commenting are talking about being efficient and not wasting their own time and energy.
It looks good in an art project or some really specific design intentions maybe but in every other circumstances it's just wrong
@@yofedstyhrega4594it's not wrong, it's just that there are better and faster ways to get the same result. Now if you are experienced you don't need a ruler.
Nice but useless
This is a terrible job, it adds more failure points and requires a lot more welding.
Não seria mais fácil cortar a chapa de baixo chanfrado e soldar a chapa de cima inteirissa, sem precisar desses recortes?
That would be the right way bud 😂 some people seem to over think simple tasks
No se puede hacer ese corte de 45º en el hierro vertical por una cuestión de geometría. Analice la situación y verá que lo que se hizo en el video es correcto.
Who would have guessed? That's good and strong and it looks great too! Thanks for sharing this with us and have a great day
У меня уже весь уголок закрашен маркером,что делать?
Оближи. Потри пальцем. Не поможет, оставь на видном месте стройки. Украдут - значит нет проблем!
O dik olanı 45 derece kesseydin daha kolay olacaktı
La otra opción es cortar el vertical a 22.5 grados y el perfil que forma la diagonal a 22.5 grados. Si es que es a 45grados .
그냥 아래기둥을 대각선으로 자르면 되잖아
REALMENTE, ERES DE LOS QUE SE LLAMAN, UN MAESTRO.
You know you don't have to draw a line on the ruler... you can just simply remember the number for the 3 seconds it took you to move the ruler.
This is city worker edition. He's doing that for the other 5 guys on the assembly line.
Or you could draw the line and not have to remember
@@pauls4704 but then you have to remember what all the other lines on your ruler are for.
You could start by not telling trained professionals how to do their jobs
@@lizzardjedi Spoken like someone with a bunch of lines on their ruler.
Love it man!!! Tips and tricks. If you don’t share the art is lost.
Just gonna say your not meant to put a mark on the stuff your keeping, even a check mark, to help avoid confusion
Yes you are. You realize they are going to be welded after that? This man is a welder/fabricator. Those little pen marks aren't going to be there for long.
Person preference. Most of us are the boss so there's no "right" way as long as you get the desired result at the end. I stopped doing checks when I moved to finish carpentry, can't mark the final product
@@joonashannila8751he's a sharpie salesman
@@joonashannila8751 oh snap, and i thought he was going to join it with ticky-tacky and bubble gum. Thank you for clearing that up for me...
Very cool video, making it look easy.
Had to turn my headphones down when the grinder came on.
Lots of lessons in under 60 Seconds
🤣🤣🤣🤣..potong yang bawah itu lebih mudah..yang atas biarkan lurus..🤣🤣🤣
Klo ada yg sulit kenapa dipermudah 😂😂😂😂
こういうちゃんと手順を教えてくれる系の動画大好き
👍 Wonderful trick of cutting shown here. Thank you.
Thank you for being very kind and generous Mr the Good Samaritan 😎
Не😢проще ли стойку срезать по углом 45 гр. А верхнею трубу целиком оставить? Сварки меньше сил потраченных тоже
Sei l'unico che ha capito
手摺りを一本で通し、柱を斜めカットした方が加工が楽で、いくつか存在するであろう柱の歪みも一本物の手摺りによって矯正される。
Nice Fabrication Thanks 👍
Thats brilliant, 100% beautifully done.
Need to learn the difference between square and rectangle.
Simplicity resulting in strength & a flush aesthetic❤
Solo habia que cortar el tubo que esta vertical en 45 grados y listo. No hacer semejante trabajo
My man I have used a lot of squares in my day of 50 years I have never seen one used with that kind of precision then I watched your video like 10 times and I still am not sure if I understand but I think I got it .that's some good stuff
Super profissional parabéns
Galing po... 👍👍
The art of making a mountain our of a mole hill.
I’m not a welder… or a fabricator. However it seems like it’d be a hell of a lot easier to just gut the vertical rail
You write on your instruments?
I think he did it so that people have a better understanding of the use of the measures.
@@abelsilvaGermanyEs muy cierto .los q no lw gustaron ese metodo es xq les gusta hacer xhambonadas
But also very cool video. Nice job on the geometry
😂😂😂😂were is Khaby Lame 😂😂😂
We need you here brother😂😂😂
Love your videos man
It's a good thing he MARKED with an "X" where to cut and marked with a "✓" so that he would NOT GET THEN MIXED UP!😮
Glad to see someone with the guard on their grinder they are a very dangerous tool
Why the fuck do you mark the ruler if it has the measurement lines?
Forgetful people will understand
Because he's making things harder than they are
Читать не умеет!
So the viewers can see what he is marking exactly?
And for the views ofcourse, because people like you get triggerd and start posting. So the videos get recommended.
The finger shakes say it all!!!
☝️👉👇🤏🤌🫰🤞✌️
Workin harder and not smarter..... as most can see
I particularly enjoyed the correct use of the tools. I teach kids in school, and it annoys me SO much when they don't use the tools available.
شكرا
Ive been welding for the last 7631 years and you've got good instincts, kid
I got lost
The way people can figure this shit out is so impressive to me. My brain cannot comprehend
아우 개 답답해 속터지겠다.
사각파이프 두개를 반듯이 놓고
가운데 들어갈거를 위에 대고 마킹하고 고대로 자르면 쉽자나 왜 저리 개 답답하게 하냐
보는사람 속터져 죽으라고 하는거야?
Thanks for pointing at the pieces. would have never guessed.
Crap
Was gonna make a joke about how I know you're hourly but if you quoted for the job good for you for pricing it in and going all the way. Looks great.
Observation is necessary for new and different ways of doing things, a lot of people including myself think about an idea after seeing others mistakes and and challenges ... i can appreciate different ways expressed of doing this cut or joint....not sure if this was a mistake, but this helps if you've made a mistake and or short on material or have reached too far in a project to just change a piece... i can appreciate the value of different routes of fixing a mistake made ... thanks
Ai comments are 🤨
@@wiggy8912 ?
Esse cara é phoda! Eu mesmo teria cortado o poste em diagonal e pronto.😮😅
Do you think it would be better to cut the lower pipe diagonally?
Надо по 22,5 градуса отрезать каждый и всё
Nice job dude! Well done!
I still don't. But I'm glad you do! Nice work.
Take a single angle piece and cut out the vertical silhouette. Less seams and even stronger.
Good work you inspire me to do better with my craft
That was clean af
very well done i,m going to mock up an example to o keep for future reference , thank you love your work
*TEKHNIK ILMU UKUR RUANG DAN ILMU SUDUT = STERIO METRIK DAN GONEO METRIK YANG DIAJARKAN SAAT SMA THN.1970'AN.*
Đặt chồng 2 hộp lên nhau. lấy dấu và cắt theo giao điểm của hai hộp ta được 2 miệng cắt bằng nhau. Khi này, đường hàn là ngắn nhất
What type of welding would you use for this metal?
Nice work😊
Well that depends, because if the stairs continue then yes, you can use that method, but if the step were the post is on has like this weird distance from the next step, you may want to use the first method to like give continuation to the way the steps go up.
Is galvanised square tube steel that where the environmentally friendly wood veneer panels are attached to?
Pretty damn nice. 🔥🔥🔥🔥🔥🔥
This is not a quiker type of application its about skill and joinery . I am a carpenter. Finish and trim is my specialty. I can appreciate the precision and the stability with the finger on the edge it stabilizes the joint . A generic person like sone of the commentators would not nitice or appreciate that lol
Cut the vertical bar diagonally and you're done
😊😊😊😊😊😊😊😊😅😊😅😅😅😊😅😅😅😊😅😅😅😅😊😊😊😊😅😅😅😅😊😊😊😊😅😅😅😅😅😅😅😊😅😊😅😅😅😊😅😊😅😅😊😅😅😅😅😅😅😅😊😅😊😅😅😅😅😅😅😊😊😅😅😊😅😅😊😊😅😊😊😊😊😊😅😅😊😊😊😊😊😊😊😊😅😅😊😅😊😊😅😅😊😊😅😊😊😅😅😅😊😊😊😊😅😅😊😅😅😊😅😅😊😅😊😊😊😊😊😊😅😊😊😊😊😊😊😊😊😅😅😅😅😅😊😊😅
Outstanding, thank you
Можно было центральный элемент под нужным углом отрезать. А если нужно было крепости конструкции добавить, то следует более сложный замок делать - для левого элемента тоже
Stronger and better to bevel the post and split the difference, so both rail ends are on top of the post.
Very nicely done many different ways to do the same job. You did a very good job with the tools you have… K-9 0Ut…
oh thats what those magnets are for. thank you! nice fit too!
درود بر شما خیلی حرفه ای اندازه میگیری من متوجه نشدم چکار کردی کارت درسته دوست عزیز❤❤❤❤❤❤❤👏👏👏👏👏👍🙌🇮🇷🇮🇷🇮🇷🇮🇷🇮🇷
Easier to hold the higher rail in line as it will eventually be set at, and then trace the post onto it. Same effect but without so much water time and extra steps.
Simplicity is best.
Is this galvanized square steel?
With the question mark, I thought this was going to be something related to Nintendo Mario World.
Cut the pillar diagonally
But that would make less work, and too much sense
Entonces no es complicado, así también lo puedo hacer yo 😃
Mas estão em posições diferentes.
Qual era o objetivo ?
É so passar o corrimão inteiro sem emendas.
People wondered why I kept a small square without any numbers on it in my toolbox.
Simple solution:
1. calculate height of angle
2. find cube that height
3. cube
I am not a welder, but this looks like a good idea.
Можно было бы нижнию стойку на искасок срезать и все.😂
Заберите у него маркер,,все поизрисовал..скажу по секрету есть способ проще с одним резом..
Awesome 👌 😊
cut the end of the post at an age and join the diagonal post in a butt weld, on top of the post. 80 % quicker and less complex.