Very helpful, am building my own floor standing speakers, with 4 (6 1/2) bas/midle tone speakers. Thank you for showing how to connect them in the right way, to get 8 ohm in total.
Those drivers look very very similar to Visaton FRS8 drivers. For better off axis response I'd recommend a horizontally curved front baffle and putting the tweeter up higher then the mid drivers. This should reduce the beaming effect you get from the current design.
Or should i just put 2 midbass in series and let the added cone area add + 3 db? And -3db from the increased impendance ? Or are my calculations wrong?
Dang fine piece of functional furniture ya built there! I don't need to know how to use power tools or build a box. I need to know how to wire up a diy bass guitar cabinet with a horn and crossover to push air at 4Ω Imma go out on a limb here and assume that the size and power and impedance is somewhat irrelevant as long as your target impedance can be met by the wiring. This is basically the same as if I were to build a 4x10 with horn and crossover for a bass guitar cabinet 4Ω at the point of power. Right? Dang! That you drumming? That's my gig but I wanna slap de bass also!
@@chrclmnky seriously. since daddy peavey retired they don't hardly answer the phone anymore. imma do this on my cab. drivers on the way. i'd jam with you any day homie. I ran this vid thru my PA and it's the shit!
Is it on a center channel on the receiver or a left/right? I know it a center sound bar I built on similar but have it 2on left and 2on right no center tweeter just 4- 6 1/2" coaxial speakers on a L/R 2 channel amp great job though 👍
Thanks Jonathan. This speaker can be re-wired for a left and right configuration but the tweeter can be only on left or right. You can build something similar and install two tweeters for a more flexible speaker feature.
Nice sound sir, I hv a doubt, what is the software u r using for box design and what is that 4400 HZ frequency ur using...and also u didn't show the back side connections of cross-over ckt..
In diagram you have in video. Green line (wire) connect with speaker's +terminal on left side but on the right side same wire is connected with - terminal of speakers. I dont get understand? Kindly guide Thanks
It probably sounds just fine, but I never liked those plastic tweeters. I like metallic domes the most, but they can be a bit expensive. These are okay if you are on a budget. The mid-woofers actually look good.
Get drok speakers, they are better... put the bass port where the Tweeter is... put the Tweeter on top or below it, if that makes sense. But either way have the bass port facing with it ( gives a little extra thump). and use MDF next time. Other than that I have to say it looks good!
4400hz has a wavelenght of 7.8cm or roughly 3.1". Considering your drivers are 3" in diameter and also spaced out a bit there is no way they are within 1 wavelenght center to center at the crossover frequency. This will cause intermodulation isseus with peaks and nulls as you move around. You need to cross overa lot lower for this and most likely second order unless your tweeter has a very low self resonant frequency (like below 1k at minimum). I also doubt bass reflex does much good with 4 drivers in that box. What frequency did you tune for? Might be better of closed, and braced. Also 4 horizontal drivers create a line array which will cause beaming and a narrow sweetspot with your tweeter beaming in the middle. You can improve this with a series lowpass over the 2 outside driver (I'd suggest first order at 300hz,all you need is 2 caps) Whenever possible install the tweeter above the center of the other speakers in a center channel. This will give you a much better high frequency dispersion. Good luck 😉
Very nice presentation sir, Need your advice ano sir magandang subwoofer for my drums and bass? my top ako na power HH 500 watts hindi ko pa makuha yung magandang tunog ng drums. Sana po sir may pwede ka isuggest sa akin. Thanks for the video dagdag kaalaman.
Brother Coaxial speaker me apni choice ke hisab se 12-15 wattage wale tweeter lgwna chahta hu too worth rhega car me music system ke liye yafir koi fayda nhi Lagwane ka
What types of speaker are best for diy boombox ? I allready have 4pis 4inc 40w(aes) woofer and i use those all 4 and now what's i need like subwoofer tweeters and quantity.?
Sir ano po ang total wattage at total impedance ng dalawang 300 watts at dalawang 150 watts tweeter Isang midrange 150 watts 8 ohms po lahat at may dividing network na 600 watts..
Yes I believe you are in a country that has aplenty of available electronic goods. Here in the Philippines so rare to find such, so I ended up DIY'ingn them.
Hello Surendra, you need to purchase a Bluetooth/digital module and connect it to your amplifier. There are many of amplifiers that already has Bluetooth and digital input/output. I hope you can find them.
Outstanding! Thank you for showing this. I am just about to finish up my truck and I was thinking about a center speaker somewhere in the dash. BTY, how did your plywood box turn out?
Your calculation for the low pass (woofer) is wrong as you have connected four 8 ohms woofers in parallel. So the effective impedance will be 2 ohms for the inductor calculation.
@@dotmunch7570 Hello, all speakers are on Shopee, but currently on queue for payment on some joy buyers. Will let you know if product will become available again due to non payment of those joy buyers.
Sir i want to make 5.1 home theater with good base.please can u tell me all spare part which are required like woofer ,speakers,tweeters,board.i want to use like home theater.directly connect to plug board in home.if u tell me i will go to electrician to connect them.please tell me sir
Hello Jordi, try the following links goodcalculators.com/crossover-calculator/ www.apicsllc.com/apics/Misc/filter2.html goodcalculators.com/resonant-frequency-calculator/
Hello Aritra, how you doin. This is a center speaker and only has single channel for CENTER channel to be hooked to your 5.1 amplifier or receiver. Home theater or PC. There is a cheap Chinese made Class D 5.1 amplifier you can buy from Aliexpress.
@@chrclmnky Daghang salamat Sir. Miski gagmay ang diameter diay sa cone kung ma cover tanang frequencies accurate gihapon. Sige mag research na sad ko sa resonance. Na duplicate ning akong comment sa vid katong usa na a sad ko comment didto.
Sounds great Sir :) i just saw the video that you've been here in Iloilo City, 2 weeks ago Sir 😅 nandito ka pa rin po ba sa Iloilo? o bumalik kna po sa Butuan City?
@@sawmill6358 Bhai Delhi ka to ni pata q ki Mai UP se hu but Han Maine Intex 2.1 ka jb subwoofer change karaya that tb vo mujhe 110 rs ka pada that Jo ki 4" ka subwoofer that
Very helpful, am building my own floor standing speakers, with 4 (6 1/2) bas/midle tone speakers.
Thank you for showing how to connect them in the right way, to get 8 ohm in total.
Those drivers look very very similar to Visaton FRS8 drivers. For better off axis response I'd recommend a horizontally curved front baffle and putting the tweeter up higher then the mid drivers. This should reduce the beaming effect you get from the current design.
Nice build Sir. Planning to do this later. Keep it up
Cool, thanks
Anup Sastry \../
I was thinking what you gonna play as a demo, perfect choice
This guy rocks!
omg thank you for showing that 4 midbass desing :D i was just thinking how to make center speaker with the same impedance as my front speakers :D
for some reason i was only thinking 2 midbass desing :D
Or should i just put 2 midbass in series and let the added cone area add + 3 db? And -3db from the increased impendance ? Or are my calculations wrong?
very awesome im trying to make a speaker for my engineering class this is a good resource!
Next level sound clarity..❤️❤️
😎🥳
Dang fine piece of functional furniture ya built there!
I don't need to know how to use power tools or build a box. I need to know how to wire up a diy bass guitar cabinet with a horn and crossover to push air at 4Ω
Imma go out on a limb here and assume that the size and power and impedance is somewhat irrelevant as long as your target impedance can be met by the wiring. This is basically the same as if I were to build a 4x10 with horn and crossover for a bass guitar cabinet 4Ω at the point of power. Right?
Dang! That you drumming? That's my gig but I wanna slap de bass also!
😎
@@chrclmnky seriously. since daddy peavey retired they don't hardly answer the phone anymore. imma do this on my cab. drivers on the way. i'd jam with you any day homie. I ran this vid thru my PA and it's the shit!
Is it on a center channel on the receiver or a left/right? I know it a center sound bar I built on similar but have it 2on left and 2on right no center tweeter just 4- 6 1/2" coaxial speakers on a L/R 2 channel amp great job though 👍
Thanks Jonathan. This speaker can be re-wired for a left and right configuration but the tweeter can be only on left or right. You can build something similar and install two tweeters for a more flexible speaker feature.
Nice sound sir, I hv a doubt, what is the software u r using for box design and what is that 4400 HZ frequency ur using...and also u didn't show the back side connections of cross-over ckt..
Hello Nandu. Sorry for the limited information about this project. Just use crossover calculators when you build your projects.
In diagram you have in video. Green line (wire) connect with speaker's +terminal on left side but on the right side same wire is connected with - terminal of speakers. I dont get understand?
Kindly guide
Thanks
Eu também construo minhas próprias caixas para meu Receiver 7.2 ... excelente trabalho de restauração parabéns !
ganda ng tunog solid na solid kahit maliit lng buong buo
It probably sounds just fine, but I never liked those plastic tweeters. I like metallic domes the most, but they can be a bit expensive. These are okay if you are on a budget. The mid-woofers actually look good.
Yes sir thanks very much for the feedback. Newbies like me still have a lot to learn. 🤓
Sir i need some guide... I have an 8inch 200w sub woofer... What components do i need to build?
A fresh sheet of MDF or plywood, some basic tools and that's it.
Get drok speakers, they are better... put the bass port where the Tweeter is... put the Tweeter on top or below it, if that makes sense. But either way have the bass port facing with it ( gives a little extra thump). and use MDF next time.
Other than that I have to say it looks good!
Yes sir thank you.
4400hz has a wavelenght of 7.8cm or roughly 3.1". Considering your drivers are 3" in diameter and also spaced out a bit there is no way they are within 1 wavelenght center to center at the crossover frequency. This will cause intermodulation isseus with peaks and nulls as you move around. You need to cross overa lot lower for this and most likely second order unless your tweeter has a very low self resonant frequency (like below 1k at minimum). I also doubt bass reflex does much good with 4 drivers in that box. What frequency did you tune for? Might be better of closed, and braced. Also 4 horizontal drivers create a line array which will cause beaming and a narrow sweetspot with your tweeter beaming in the middle. You can improve this with a series lowpass over the 2 outside driver (I'd suggest first order at 300hz,all you need is 2 caps) Whenever possible install the tweeter above the center of the other speakers in a center channel. This will give you a much better high frequency dispersion. Good luck 😉
Nice. I appreciate the feedback. Will do. Thanks.
Very nice presentation sir, Need your advice ano sir magandang subwoofer for my drums and bass? my top ako na power HH 500 watts hindi ko pa makuha yung magandang tunog ng drums. Sana po sir may pwede ka isuggest sa akin. Thanks for the video dagdag kaalaman.
Another great job CM👍
Thanks Andy
Brother Coaxial speaker me apni choice ke hisab se 12-15 wattage wale tweeter lgwna chahta hu too worth rhega car me music system ke liye yafir koi fayda nhi Lagwane ka
Nice build man. Sounds great.
Thanks Chris.
Will you show those speakers wiring diagram, plz?
3:49
Do you have any DIY Satellite Speaker? and how about the Amp for Center and Satellite? Thanks in Advance
Hello Monzur, I hook all my speakers to a mini 5.1 class D amp shown in the beginning of the video on my desktop.
te quedo maravilloso, por como diseñaste el cajón se ha de escuchar muy nítido el audio... felicidades te quedaron increíbles
Thanks. 😊
What types of speaker are best for diy boombox ? I allready have 4pis 4inc 40w(aes) woofer and i use those all 4 and now what's i need like subwoofer tweeters and quantity.?
Yes you need subwoofer to add bass.
ganda neto boss sana madali lng gawin yang crossover
Sir ano po ang total wattage at total impedance ng dalawang 300 watts at dalawang 150 watts tweeter
Isang midrange 150 watts
8 ohms po lahat at may dividing network na 600 watts..
New SUBSCRIBER here🎉🎊
Great DIY Sir💯✨
Tanong ko lang Sir ano dimensions ng speaker box?😊
Thanks. There is a better center channel speaker project, go to this video - ua-cam.com/video/66dKLHq3wi0/v-deo.html
Salamat Sir 😃👍
Bisaya diay ko Sir 😁
Ganahan kaayo ko sa imoha DIY Sir💯👏
Pila pud pabuhat ana Sir?😄
Nice video, can i use a same wireing for the 2nd order Linkwitz Riley?
This wiring will reverse the polarity on 2nd orders.
Thank you for answer, i'm still learning about this so i will use a 1order like you in the video. Keep up with a good work!
нормальная система , а кто был Ваш помощник на четырёх ногах ? ))
what plywood is that by looking it not a birch?
Hi you used mid range speaker,can I buy the cross over some where?, thank you
Yes I believe you are in a country that has aplenty of available electronic goods. Here in the Philippines so rare to find such, so I ended up DIY'ingn them.
and how we add small Bluetooth amplifier to connect the usb mic and memory card etc nd amplifier is may be 250 watt support
Hello Surendra, you need to purchase a Bluetooth/digital module and connect it to your amplifier. There are many of amplifiers that already has Bluetooth and digital input/output. I hope you can find them.
Here's you was use MDF so sounds is awesome after all
Solid naman po idolo .. how much po kaya magpa build sa inyo ng ganyan??
Thanks. Meron ako gawa yung white automotive finish, for sale ko. Check nyo video sa channel.
Outstanding! Thank you for showing this. I am just about to finish up my truck and I was thinking about a center speaker somewhere in the dash. BTY, how did your plywood box turn out?
Hello Robert, that project was a fail. Watch this recently done center speaker. - ua-cam.com/video/66dKLHq3wi0/v-deo.html
You can use any song here for better your speakers
hey bro thanks for sharing your video nice and cool, so you can set up a speaker?
No problem, anytime. Let me know anything I can be of any help.
Where did you buy the speakers?
Hello Raynedson, bought them from a local audio-electronics store here in my city.
Your calculation for the low pass (woofer) is wrong as you have connected four 8 ohms woofers in parallel.
So the effective impedance will be 2 ohms for the inductor calculation.
Parallel - series. Look closely .
Where do you get the square Tweeter at or what's the name of it so I can get four pair
Hello Horace. It is just a common 3" woofer. Mostly available in that shape. The circle ones are bit expensive.
Hello,
how do you calculate wire size ?
Hello there is an online tool in winding coils - www.pronine.ca/multind.htm
Kuya paturo nman ako pano gawin ung cross over mo?gusto ko din gawin tong center speaker mo eh.thanks
Madali lang. Watch my other video about crossover building.
which frequency did u use for calculating inductance?
Sorry I forgot the specific frequencies but I used these calculators:
www.apicsllc.com/apics/Misc/filter2.html
@@chrclmnky must be 1khz normal LCR meter thanks for the site 👍
Boss pwede rag katong mga amplifier kasagaran sa mga motorcab nga 12v gamiton ana? Tnx
O pwede ra man sir.
@@chrclmnky bisaya diay ka kol. asa dpit inyuha?
@@iangleamergegare6330 diri sa Butuan City sir. 😎
How do you connect 4 or more speaker on a stereo Bluetooth module?
Iluminati 0:50
Any reason why you inserted the cotton foam inside?
Hello Justin, they are polyester fiber fill. Stuff them inside to eliminate speaker vibration from resonance.
CHRCLMNKY oh okay
(full range speaker) series parallel combination, similar from bose 901
what is RMS wattage of your amplifier
Just 200 i think
@@chrclmnky ohh means u can add 4 more same speakers? by d way thanx for ur reply
All speaker connection in parallel?
Series - parallel
Sir what is the length and the width of box???
sna yung sunod mong build is 2 way tower speaker nmn with 3pcs 8 inch driver and a tweeter.. heheh.. looking forward for your nxt project sir
Yes sir. Medyo mahal din puhunan gumawa ng tower speakers. :) But will try to save up for those. :) Thank you for dropping by.
Ano gamit no para makapag UA-cam SA led TV NA kits KO ksi may box NA connectado SA TV pls loss pa reply
Android TV Box. I suggest Xiaomi TV Box
how much sir and sana online pwede omorder? Thank you
@@dotmunch7570 Hello, all speakers are on Shopee, but currently on queue for payment on some joy buyers. Will let you know if product will become available again due to non payment of those joy buyers.
Please give me link from you buy this speakers
Sir i want to make 5.1 home theater with good base.please can u tell me all spare part which are required like woofer ,speakers,tweeters,board.i want to use like home theater.directly connect to plug board in home.if u tell me i will go to electrician to connect them.please tell me sir
Let me guess, you are indian?
@@nikolapoljak9260 yes sir
@@nikolapoljak9260 wt is the problem if we are Indians..can't u tell us the Speakers specifications..
Read the description. He use a generic speaker w/c can be bought online. Idk if thats available in your country.
Felicitaciones amigo! Me gusta mucho el diseño. Saludos.
Thank you Jairo.
box size?
may i get the solo drum video you played on the demo?
Hello Teguh, yes sure, here's the link to Anup Sastry's drum video ua-cam.com/video/yrkVX8KFPQA/v-deo.html
I have 3 different speakers so how do I help it in 1 cabin at the same time
What do you call that coil thingy?
Inductor coil. Use to filter out high frequencies.
Does that crossover website work well or are there better websites for that? Anybody?
Hello how you doin, practically all other crossover calculator web based apps are pretty much the same.
I did not understand the connection of the speakers think that they would all be connected in parallel what is the final impediment grateful
Hello Marcelo, a combination of series and parallel as shown in 3:51
Use cross over
@@lovekush9103 yes it has
o really luv ur work u upload
thank you 😁
what is this page for calculate the condensador and capacitor? for the crossover
Hello Jordi, try the following links
goodcalculators.com/crossover-calculator/
www.apicsllc.com/apics/Misc/filter2.html
goodcalculators.com/resonant-frequency-calculator/
Please could you tell me what was the total wattage for this set of speakers?
Can handle up to 300w RMS @ 6 Ohms
Salamat po sir
Which amplifier(watt) is suitable for this sound bar???
Hello Aritra, how you doin. This is a center speaker and only has single channel for CENTER channel to be hooked to your 5.1 amplifier or receiver. Home theater or PC. There is a cheap Chinese made Class D 5.1 amplifier you can buy from Aliexpress.
You can hook up amplifier with 50-200w with this one.
Can i use TPA3118 PBTL Digital Amplifier with usb power run
Yes you can
Sir can u teel me what is the length or breath of this box
The dimensions are 24"x6"x7"
Bai pa advise unsay size sa speaker for vocals. Plano unta naku for videoke gamay ra nga column speaker pero clear ang vocals ug instrumentals.
Wala na sa size sir. Sa resonance and frequency response ra na sukdon.
@@chrclmnky Daghang salamat Sir. Miski gagmay ang diameter diay sa cone kung ma cover tanang frequencies accurate gihapon. Sige mag research na sad ko sa resonance. Na duplicate ning akong comment sa vid katong usa na a sad ko comment didto.
@@chrclmnky New subscriber here Sir. Very informative DIY Channel. (y)
Magnífico trabajo compañero...enhorabuena.....
can you give me the dimension of the box speaker?
Can you make one for deeper bass n only 2 speakers and 2 tweeters
Yes sure
@@chrclmnky CAN YOU SALE IT TO ME I WANT TO UPGRADE MINE
Sir may video po ba kayo kong pano gawin yang crossover at icalculate ? Salamat po..
Yes sir, watch my old videos. Also that 100percent diy crossover on my channel. Thanks!
@@chrclmnky okay thanks
Teh
@@dakshshaurya9817 ate ?
boss capacitor yang nagkalagay sa may tweeter???
Single capacitor to filter 6dB slope.
Boss anu mganda n car stertio pra s trisicle po?
At speker po
Can you tell me the speaker connection diagram?
Hello Shivanish, there is a wiring diagram in the video. It consists of parallel and series to obtain the right DC resistance and impedance.
Thank you 😀
@@chrclmnkycan you please tell me the box dimension ??
Suggest me cross over ?? For it
Sounds great Sir :)
i just saw the video that you've been here in Iloilo City, 2 weeks ago Sir 😅
nandito ka pa rin po ba sa Iloilo? o bumalik kna po sa Butuan City?
Thanks for watching. Just 2 days in Iloilo for the WordCamp. 😆
@@chrclmnky Ahh, hehe 😅You're welcome po Sir 🙂
God Bless po and more vids/DIY projects to come 🙂
Sir how can i contact you i want you to make me an dividing network for 400 watts 2way Treble only?
Sorry. I've stopped building crossovers. They are so tedious to make.
What are your messurments of the box please
i have JBL FLIX1 and can you take video how i can input in + -
Is this an 8ohm speaker?
Yes they all are 8 Ohm speakers.
Hello , how can i get these hifi loudspeakers ?
Hi, build them.
@@chrclmnky i mean only speakers (magnum) , how to get these speakers
Bai pwde ba ug mas taas ang watts ani nga setup like 100 watts per woofer?
Pwede ra man.
nice drum solo
yes, dude's a beast
That configuration has to be a 2 1/2 or 3 way. It can't be a 2 way. It will sound much better!
Next time use a hole saw for the larger speaker holes. Jig Saw for 4 round holes seems counter-intuitive, sloppy, and slow.
I agree.
Nice work keep it up man.....
Wow
Thank you very much. ^_^
your welcome ^_^
can you show me full wiring for this speaker
wait.
www.rockfordfosgate.com/support/wiringwizard.aspx
Sir sa raon mo binili yang speakers na yan?
No, at a local electronics/audio store here in our province.
boss,please give me a video if how tto stoolling the wiring the 4 speaker and twetter tnx
U
What software did you use?
TinkerCad - layout and design
boss ilang watts na amplifier ang pwd sa ganyan?salamat
150-700w
Is the tweeter Dayton?
A generic Chinese-made, square Yamaha tweeter copy.
Sir how much apply volt in this divise
Amigo cual es su esquema del circuito conectado?
What is price of that speaker?
how much
Sir what inches speaker
4" Woofer Speakers
भाई फिर एक स्पीकर कितने रुपए का पड़ेगा चारों सेट कितने का पड़ेगा भाई ओनली स्पीकर
Hello Sachin, speaker is very cheap here in the Philippines.
180x4
Bro in India it will cost you around 150 Rs for each 4" Woofer but go for better one which will cost you around 200 rs and more for each
@@shresthguptaMG Bhai which shop provides it for this low amount? I would definitely like to know... Delhi NCR mein pata ho toh aur bhi badhiya
@@sawmill6358 Bhai Delhi ka to ni pata q ki Mai UP se hu but Han Maine Intex 2.1 ka jb subwoofer change karaya that tb vo mujhe 110 rs ka pada that Jo ki 4" ka subwoofer that
Bhi eska amplefire kitna watt ka ha bhi plz mujko thora bathoui
4.1 का bass कैसे बनाते हैं👍