КОМЕНТАРІ •

  • @maheenvohra1389
    @maheenvohra1389 8 місяців тому +1

    bulb is not switching off what is the reason?

  • @ChinmayDhumal
    @ChinmayDhumal 5 років тому +2

    Thanks for the video, made a nice mini project within an hour at last moment!

    • @RaianShahrear
      @RaianShahrear 4 роки тому

      you are most welcome

    • @bowenpeyton4087
      @bowenpeyton4087 3 роки тому

      A tip: watch movies at flixzone. Been using them for watching a lot of movies during the lockdown.

    • @jadenjasper3471
      @jadenjasper3471 3 роки тому

      @Bowen Peyton Yup, been using flixzone for since december myself :D

  • @archanapurnsingh3646
    @archanapurnsingh3646 Рік тому +1

    Thanks brother this project is working, the only thing you have to do is to flash the mobile torch intesive light on the LDR to get the LED ON !!

  • @kanchankhhj
    @kanchankhhj Рік тому +1

    Light is not turning off so what should I do

  • @sadianaseer7524
    @sadianaseer7524 3 роки тому +2

    It is very useful information for me thnk u sir

  • @Rohgu
    @Rohgu Рік тому +1

    if IC is overheating what to do??

  • @faizanrandhawa607
    @faizanrandhawa607 5 років тому +1

    Why you are using high power ceramic resistor¿

    • @psubond
      @psubond 5 років тому +1

      Most likely because that is what he had on hand in that value

  • @growthgamerzyt.2004
    @growthgamerzyt.2004 Рік тому

    Is there Any chance using doing with jk flip flop

  • @pranavj1066
    @pranavj1066 5 років тому

    Can I use 1/4 watt 330 ohm resistor instead of 5 watt 330 ohm resistor

  • @EEBVamsiVenkatKotala
    @EEBVamsiVenkatKotala 2 роки тому +2

    Hello sir what changes we have to do to this circuit to work this opposite conditions . Like when light is not there it should glow and when light is there it should put off .. could you please tell me ..

    • @islamsafer7101
      @islamsafer7101 2 роки тому

      you can use and gate for that or inverter in the output

    • @anitabolegaon9583
      @anitabolegaon9583 2 роки тому

      Just turn out LDR and connect it reverse

  • @rakibhassan3217
    @rakibhassan3217 2 роки тому

    glow of LED is gotten very low when I have implemented the circuit

  • @asadullahmari245
    @asadullahmari245 6 років тому +1

    Can we use another nand gate just like ttl family

    • @RaianShahrear
      @RaianShahrear 5 років тому

      Yes you can. Then for 2nd Nand gate, have to make one pin '0' and another pin '1'. But in this circuit, using of 2 Logic Gates is costly and usless. To understanding the circuitry: drive.google.com/file/d/0B0WETgsj_cTbX2RyWldpTDFaM00/view

  • @rajunagpal393
    @rajunagpal393 5 років тому

    Can we use photoresistor instead of LDR ?

    • @wajahaat
      @wajahaat 4 роки тому

      can you please tell me how to find photoresistor on multisim

    • @RaianShahrear
      @RaianShahrear 3 роки тому

      Full elaboration of LDR is light dependent resistors which is one kind of photo resistor. This special type of resistor is controlled with intensity of light.
      Read more: eepower.com/resistor-guide/resistor-types/photo-resistor/#

  • @DigitalBangaliz
    @DigitalBangaliz 5 років тому

    Raian Shahrear, where can i get those element in Dhaka?

    • @RaianShahrear
      @RaianShahrear 5 років тому

      Online Shop: www.techshopbd.com and bdspeedytech.com
      or you can find those things at Mirpur-01, Gulistan Stadium Market, Patuatoli in Dhaka city.

  • @aebybabli02
    @aebybabli02 3 роки тому

    What is the use of this project in future ?

    • @RaianShahrear
      @RaianShahrear 3 роки тому

      This can help anyone to understand about constructing a circuit diagram, basic working principle of MOSFET and logic gate. Thank you.

  • @webmovies3312
    @webmovies3312 3 роки тому +2

    Thank you sir

  • @achalasrikaza2994
    @achalasrikaza2994 6 років тому +1

    how to select resistor values

    • @RaianShahrear
      @RaianShahrear 5 років тому

      Here resistor used for protection. For LDR, keep it above 1K ohm and for LED, keep it 100 to 500 ohm.

  • @balrajkoli8694
    @balrajkoli8694 6 років тому

    Konsa LDR use kiya he...

  • @danaodanekamie3910
    @danaodanekamie3910 2 роки тому

    Hello, may I know what are the procedures of your video?

    • @RaianShahrear
      @RaianShahrear 2 роки тому

      Please see the details: drive.google.com/file/d/0B0WETgsj_cTbX2RyWldpTDFaM00/view?usp=sharing&resourcekey=0-yxFH7ufyHXJgElGCm-ChUw

  • @emonsahariar9292
    @emonsahariar9292 Рік тому +4

    And you call it presentation?

  • @emansajid3662
    @emansajid3662 5 років тому

    Sir muja is ki soft form chaya agr ap muja is k soft form ka link baaj da

  • @zeshanali1102
    @zeshanali1102 4 роки тому +1

    so why u don't use not gate instead of nand gate

    • @RaianShahrear
      @RaianShahrear 3 роки тому

      My experiment was to learn about universal logic gate. So I used this instead of NOT gate. Thank you.

    • @pratyushlandekar9560
      @pratyushlandekar9560 Рік тому

      @@RaianShahrear so can we use not gate instead?

  • @imthiasshamsudeen5938
    @imthiasshamsudeen5938 5 років тому

    It is not working.... Tried many time... But still no change

  • @Lmjgm
    @Lmjgm 5 років тому +1

    abe bina IC lagaye drct bttry resistr LDR aur LED series me laga deta to bhi yhi kaam krta.....

    • @RaianShahrear
      @RaianShahrear 5 років тому

      Yes, there are many ways to run this project, but here the main objective was to understand the operation of Logic Gate.

    • @kumarrishabh1216
      @kumarrishabh1216 5 років тому

      Exactly,, brother...

  • @vivekviv4818
    @vivekviv4818 6 років тому +1

    This project is not working at all

    • @vivekviv4818
      @vivekviv4818 5 років тому

      @@RaianShahrear tried even that but won't work I don't know what was the problem

    • @RaianShahrear
      @RaianShahrear 5 років тому

      I'm apologies for my bad English. Turn on the Subtitle option and watch this again. May be you will understand. and also you can check this out for understanding the circuitry: drive.google.com/file/d/0B0WETgsj_cTbX2RyWldpTDFaM00/view

  • @praveenkundargi6161
    @praveenkundargi6161 7 років тому

    it is very helpful!! thank you soo much
    i just want logic diagram of that ..plz can u send??

    • @RaianShahrear
      @RaianShahrear 7 років тому

      Thanks.
      Check this out drive.google.com/file/d/0B0WETgsj_cTbX2RyWldpTDFaM00/view

  • @sakeefhasan
    @sakeefhasan 4 роки тому +1

    👍

  • @muhammadaqeelyousafzai7665
    @muhammadaqeelyousafzai7665 6 років тому

    is me to ho he ni raha on yare

  • @shaafahmed5984
    @shaafahmed5984 6 років тому

    GREAT VIDEO.........

  • @sanaasghar5204
    @sanaasghar5204 3 роки тому

    Light turn off krne led band nhi horhi hy

    • @RaianShahrear
      @RaianShahrear 2 роки тому

      Please check your circuit connection, and if not worked, please change the LED or NAND Gate IC.
      Thank you.
      Circuit details: drive.google.com/file/d/0B0WETgsj_cTbX2RyWldpTDFaM00/view?usp=sharing&resourcekey=0-yxFH7ufyHXJgElGCm-ChUw

  • @yuvrajsharma2134
    @yuvrajsharma2134 6 років тому

    good😄

  • @akr1686
    @akr1686 6 років тому

    I dint see the video completely. I dint understand anything. Sorry sir for this. I had to comment.

    • @RaianShahrear
      @RaianShahrear 5 років тому

      I'm apologies for my bad English. Turn on the Subtitle option and watch this again. May be you will understand. and also you can check this out for understanding the circuitry: drive.google.com/file/d/0B0WETgsj_cTbX2RyWldpTDFaM00/view

  • @hidajetstrika4278
    @hidajetstrika4278 4 роки тому +1

    I've been researching into circuits and discovered an awesome website at Gregs Electro Blog (google it if you're interested)

  • @ee66subodhchitte4
    @ee66subodhchitte4 5 років тому

    Coding

    • @RaianShahrear
      @RaianShahrear 2 роки тому

      If you want, you can use microcontroller or that kind of staffs. But here the goal of the project was to learn the basic of #Universal_Gate.
      Thank you.

  • @Editlives
    @Editlives 4 роки тому +1

    Bhai tere english ek no ha 😂😂english nolna sikh phele fir bola kar😂😂😂

    • @RaianShahrear
      @RaianShahrear 3 роки тому

      Please excuse my English. Turn on the caption while watching this video. Thank you.
      For more info: drive.google.com/file/d/0B0WETgsj_cTbX2RyWldpTDFaM00/view