Thank you very much for explanation.You said it is advisable to remove the filters and block the hoses before rinsing. Can we use pure gasoline without mixture? Is it necessary to remove the filter in the oil tank and plug the hoses before flushing?
The oil filter does not need such frequent maintenance. The oil filter can be accessed by removing the clutch assembly.I don't know which chainsaw model you have, let's say it's some autotune product, mostly this system is similar to all professional chainsaw models. It will not be possible to remove the oil filter through the oil cap hole, it must be done from the clutch side. If there is no problem with the oil supply, just empty out the oil tank, put some of fluid in it ( fuel) and rinse it out.
@@AutoTuneTM The pipe that goes from the carburetor to the petrol tank, I used a poor amount of oil to make the 2-stroke mixture and I would like to clean the pipes from oil residues in the mixture, and I was wondering how to do it, if it is convenient with a syringe, detaching the pipe from the carburetor and pushing diesel fuel up to the tank
Can u explain what you are putting in the oil container to clean it (gas as well)?? And Is the same bar & oil that is used to mix in part with the gas, what you fill the oil up with?
Bar&chain oil is for lubricating the saw when it is in the wood. 2-stroke oil is for mixing with gasoline. He uses gasoline to wash the oil reservoir because it will dissolve petroleum sludge and gunk. Gasoline also evaporates quickly.
Great video thanks. I would like to know what you were using in the oil tank to help clean it tho.... i found a chainsaw in a river bank and am trying to bring it back to life. The chain oil has definitely been contaminated with water. Haha we shall see how it goes....
Impeccable and precise instructions and communication. Had he said any more it would have been lost in translation.
Informative video. For me, everything is clear after watching it.
Thank you very much for sharing the procedure. 🙂👍
How long do you need to let it sit before you can put more bar oil in it.
Thank You very precise and clear......
Thank you very much for explanation.You said it is advisable to remove the filters and block the hoses before rinsing.
Can we use pure gasoline without mixture?
Is it necessary to remove the filter in the oil tank and plug the hoses before flushing?
The oil filter does not need such frequent maintenance. The oil filter can be accessed by removing the clutch assembly.I don't know which chainsaw model you have, let's say it's some autotune product, mostly this system is similar to all professional chainsaw models. It will not be possible to remove the oil filter through the oil cap hole, it must be done from the clutch side. If there is no problem with the oil supply, just empty out the oil tank, put some of fluid in it ( fuel) and rinse it out.
How do I clean the tubes that go from the two fuel tanks to the carburettor?? To eliminate old oil and mixture?
What tubes are you talking about? The normal action is to buy a new hoses and replace it.
@@AutoTuneTM The pipe that goes from the carburetor to the petrol tank, I used a poor amount of oil to make the 2-stroke mixture and I would like to clean the pipes from oil residues in the mixture, and I was wondering how to do it, if it is convenient with a syringe, detaching the pipe from the carburetor and pushing diesel fuel up to the tank
Can u explain what you are putting in the oil container to clean it (gas as well)?? And Is the same bar & oil that is used to mix in part with the gas, what you fill the oil up with?
Bar&chain oil is for lubricating the saw when it is in the wood.
2-stroke oil is for mixing with gasoline.
He uses gasoline to wash the oil reservoir because it will dissolve petroleum sludge and gunk. Gasoline also evaporates quickly.
Good job ;)
What was the new part that got used at 12.51 please?
Fuel Filter 5034432-01
What did you use to close the fuel line off?
I don't understand why there's no commentary explaining what and why.
Can you let me know how much hasqvara 2t oil should mix with 1 letter of fuel oil?
20ml of quality two stroke oil per 1liter of fuel.
@@AutoTuneTM thank you so much🙏🙏👍
Great video thanks.
I would like to know what you were using in the oil tank to help clean it tho.... i found a chainsaw in a river bank and am trying to bring it back to life. The chain oil has definitely been contaminated with water. Haha we shall see how it goes....
All visual debris from both tanks is flushed with gasoline. It is advisable to remove the filters and block the hoses before rinsing.
@@AutoTuneTM thanks !!