SBI - Stove Builder International
SBI - Stove Builder International
  • 59
  • 194 423
How to replace the door gasket of a wood stove?
Here's a simple tutorial on how to replace the door gasket of your wood-burning appliance - stove, insert, furnace or fireplace!
Required:
- High temperature tape
- Sheet of paper
- Scissors
- Nitrile gloves and towel
- Gasket and high temperature silicone
- Hammer, flathead screwdriver and locking pliers
Steps:
1. Remove the door and place it on a flat surface protected by a towel or rug.
2. Remove the latch stop pin so as to have more room to work.
3. Before proceeding with the following steps, be sure to remove the old seal from the door and clean the groove thoroughly by scraping and vacuuming it. Prior to installing the door gasket, put on protective gloves. Then put high temperature tape on one end of the gasket and cut through its center.
4. Apply a 3/16" bead of high temperature silicone into the door groove. If necessary, wipe off any excess silicone before it hardens.
5. Starting 2/3 of the way across the bottom of the door, apply the gasket into the groove. The gasket should not be stretched during this procedure all the while making sure to compress it every inch.
6. Leave about 1/2'' of cord protruding. Apply tape, then cut in the center of it with the scissors. Compress the gasket again and push the end into the groove. Leave to dry for 24 hours.
7. Install the door. To check the seal, place a sheet of paper in the door opening, close the door and try to remove the sheet. If it is easy to remove, tighten the handle.
8. Make any necessary adjustments until the sheet remains set. Reinstall the pin using a hammer.
Переглядів: 2 883

Відео

Comment remplacer le cordon de porte de mon poêle à bois?
Переглядів 8 тис.Рік тому
Voici un tutoriel simple pour changer le cordon de porte de votre appareil de chauffage au bois - poêle, encastrable, fournaise ou foyer! Requis : - Ruban autocollant et feuille de papier - Ciseaux - Serviette et gants de nitrile - Cordon et silicone haute température - Marteau, tournevis plat et pince de serrage Étapes : 1. Retirez la porte et placez-la à plat sur une surface douce telle qu'un...
How to Adjust the Door Hinges of a Wood Stove?
Переглядів 3 тис.Рік тому
Here's a simple tutorial on how to adjust the door hinges of your wood-burning appliance - stove, insert, furnace or fireplace! Required: - Flat head screwdriver - 3/32'' Allen key Steps: 1. Open the appliance door. Using a 3/32" Allen key, slightly unscrew the set screws located on the door hinges to release the adjustable hinge pins. 2. Remove the door to make adjustments. Using a flat head s...
Comment ajuster les pentures de porte d'un poêle à bois?
Переглядів 729Рік тому
Voici un tutoriel simple pour ajuster les pentures de porte de votre appareil de chauffage au bois - poêle, encastrable, fournaise ou foyer! Requis : - Tournevis plat - Clé Allen de 3/32'' Étapes : 1. Ouvrez la porte de l’appareil. À l’aide d’une clé Allen de 3/32", dévissez légèrement les vis de pressions situées sur les gonds de porte pour libérer les tiges de pentures ajustables. 2. Enlevez ...
Comment remplacer les tubes d'air secondaire d'un poêle à bois?
Переглядів 785Рік тому
Voici un tutoriel simple pour remplacer les tubes d’air secondaire de votre appareil de chauffage au bois - poêle, encastrable, fournaise ou foyer! Requis : - Pince de serrage - Tube (s) de remplacement Étapes : 1. À l'aide d'une pince de serrage ou de vos mains, retirez les tubes d'air secondaire que vous désirez remplacer. Prenez soin de noter l'emplacement de chaque tube pour les replacer au...
How to Replace the Secondary Air Tubes of a Wood Stove?
Переглядів 2,8 тис.Рік тому
Here's a simple tutorial on how to replace the secondary air tubes of your wood-burning appliance - stove, insert, furnace or fireplace! Required: - Locking pliers - Secondary air tubes Steps: 1. Using locking pliers or your hands, remove all secondary air tubes. The number of tubes may vary depending on the model. It is important to identify each tube as they need to be reinstalled in the same...
Comment remplacer le coupe-feu d'un poêle à bois?
Переглядів 1,4 тис.Рік тому
Voici un tutoriel simple pour remplacer le coupe-feu de votre appareil de chauffage au bois - poêle, encastrable, fournaise ou foyer! Requis : - Pince de serrage - Coupe-feu de remplacement Pour retirer l'ancien coupe-feu : 1. Soulevez le coupe-feu en le poussant du bout des doigts, déplacez le vers le côté et l'arrière, puis déposez le sur les canalisations. 2. Appuyez le coupe-feu sur les tub...
How To Replace the Baffle of Your Wood Stove?
Переглядів 3,6 тис.Рік тому
Here's a simple tutorial on how to replace the baffle of your wood-burning appliance - stove, insert, furnace or fireplace! Required: - Locking pliers - Replacement baffle To remove the old baffle: 1. Slightly lift the baffle and slide it towards the rear and side so it can sit on the air channels welded to the firebox. 2. Using locking pliers or your hands, remove all secondary air tubes. The ...
How does the double combustion of a wood stove work?
Переглядів 19 тис.Рік тому
Here's how the double combustion of a non-catalytic wood stove works (EPA): 1. The pull generated by the chimney allows the intake of fresh air through the openings in the unit. 2. The primary supply of air injects oxygen onto the embers and wood. 3. This causes the fuel to burn, which releases gases and fine particles. 4. Secondary air introduces oxygen into the hot gases released by the first...
Comment fonctionne la double combustion d'un poêle à bois?
Переглядів 28 тис.Рік тому
Voici comment fonctionne la double combustion d'un poêle à bois non-catalytique : 1. Le tirage généré par la cheminée permet l'admission d'air frais par les orifices de l'appareil. 2. L'air primaire injecte de l'oxygène dans les braises et sur le bois. 3. Le combustible brûle, ce qui libère des gaz et de fines particules. 4. L'air secondaire injecte à nouveau de l'oxygène dans les gaz chauds li...
How to choose the right wood stove?
Переглядів 821Рік тому
Are you looking for the best wood stove and need help making an informed choice? Here are our recommendations to understand your needs and choose the right stove for you. 1. What floor will the wood stove be installed on and how many stories are above it? 2. Will the heat flow easily? 3. How effective is your insulation? 4. How will you use your wood stove? 5. How to calculate the area to be he...
Comment choisir le bon poêle à bois?
Переглядів 7 тис.Рік тому
Vous êtes à la recherche du meilleur poêle à bois et vous avez besoin d'aide pour faire un choix éclairé? Voici nos recommandations pour bien cibler vos besoins et choisir le bon appareil pour vous. 1. À quel étage sera installé le poêle à bois et combien d’étages y a-t-il au-dessus? 2. Est-ce que la chaleur circulera facilement? 3. Quelle est la qualité de votre isolation? 4. Quelle utilisatio...
La robotisation chez SBI
Переглядів 1602 роки тому
Pour en savoir plus sur les postes disponibles et la vie chez SBI : www.sbi-international.com/fr/carrieres
Être opérateur de presse chez SBI
Переглядів 4402 роки тому
Chez SBI, les opérateurs de presses travaillent sur des presses plieuses (Trumpf) ! Si tu es débrouillard et manuel, c'est un poste parfait pour toi. Pour en savoir plus sur les postes disponibles et la vie chez SBI : www.sbi-international.com/fr/carrieres
L'ingénierie de produit chez SBI
Переглядів 1592 роки тому
Pour en savoir plus sur les postes disponibles et la vie chez SBI : www.sbi-international.com/fr/carrieres
Être chargé de compte chez SBI
Переглядів 2862 роки тому
Être chargé de compte chez SBI
Deviens Soudeur chez SBI
Переглядів 4924 роки тому
Deviens Soudeur chez SBI
4.0 chez SBI
Переглядів 6104 роки тому
4.0 chez SBI
Travailler dans l'équipe d'ingénierie d'usine chez SBI
Переглядів 3114 роки тому
Travailler dans l'équipe d'ingénierie d'usine chez SBI
Être manoeuvre chez SBI
Переглядів 8584 роки тому
Être manoeuvre chez SBI
Pellet Stove Maintenance (top feed) | 5 cleaning steps
Переглядів 20 тис.4 роки тому
Pellet Stove Maintenance (top feed) | 5 cleaning steps
Entretien poêles à granules (alimentation par le haut) | 5 étapes de nettoyage
Переглядів 1,2 тис.4 роки тому
Entretien poêles à granules (alimentation par le haut) | 5 étapes de nettoyage
Pellet Stove Maintenance (bottom feed) | 5 cleaning steps
Переглядів 1,6 тис.4 роки тому
Pellet Stove Maintenance (bottom feed) | 5 cleaning steps
Entretien poêles à granules (alimentation par le bas) | 5 étapes de nettoyage
Переглядів 7934 роки тому
Entretien poêles à granules (alimentation par le bas) | 5 étapes de nettoyage
EPA 2020: SBI is ready!
Переглядів 2664 роки тому
EPA 2020: SBI is ready!
Comment optimiser la qualité de la combustion?
Переглядів 14 тис.4 роки тому
Comment optimiser la qualité de la combustion?
How to optimize the quality of combustion?
Переглядів 1,8 тис.4 роки тому
How to optimize the quality of combustion?
Comment bien allumer mon foyer ou poêle à bois?
Переглядів 2,7 тис.4 роки тому
Comment bien allumer mon foyer ou poêle à bois?
How to properly light my wood stove or fireplace?
Переглядів 2 тис.4 роки тому
How to properly light my wood stove or fireplace?
Performance des nouveaux poêles à bois
Переглядів 9194 роки тому
Performance des nouveaux poêles à bois

КОМЕНТАРІ

  • @dominicgignac7595
    @dominicgignac7595 8 днів тому

    On a la max caddy 👌

  • @MrTonyHeath
    @MrTonyHeath 21 день тому

    Would have been a better demonstration if the stove had actually been dirty and not straight out of the box.

  • @christophefaujanet2053
    @christophefaujanet2053 2 місяці тому

    Jamais de papier. L encre dedans est nocive pour la santé

  • @jimshaw8634
    @jimshaw8634 4 місяці тому

    Thanks,

  • @coraliesw3626
    @coraliesw3626 5 місяців тому

    Merci beaucoup ❣️

  • @sorrykay3450
    @sorrykay3450 7 місяців тому

    But where is the secondary air coming from. It's all closed at the top

    • @leofortey7561
      @leofortey7561 4 місяці тому

      From the back or sides. It is fresh air that gets heated by the flames, sending hot oxygenated air to the top which helps burn excess wood gases that would otherwise go up the chimney.

  • @slavoie1027
    @slavoie1027 8 місяців тому

    j'ai entendu parler de "TRIPLE COMBUSTION". Ai-je rêvé ?

  • @John-viheavyequipment
    @John-viheavyequipment 11 місяців тому

    I still dont understand this at all the top of the door near the hinge is further way fromthe stove then the bottom of the door by the hingehow do i adjust the door to be tighter against the stove at the top?

  • @zero-tc9vr
    @zero-tc9vr 11 місяців тому

    ça aurait été bien mieux de nous montrer un vrai feu.

  • @JP-bb3jn
    @JP-bb3jn 11 місяців тому

    Merci votre vidéo est courte et pédagogique. Cela permet de comprendre, ce que je ne parvenait pas. 1 question svp L air secondaire arrive naturellement (sans ventilateur ?) comme l air primaire ???? Merci à vous

  • @michel9877
    @michel9877 11 місяців тому

    Idiot, ça chauffe ou pas?

  • @chrisE815
    @chrisE815 11 місяців тому

    I have an Osburn 2000. Should the baffle be resting on top of the secondary air tubes?

  • @victoryfirst2878
    @victoryfirst2878 11 місяців тому

    Nice explanation of the process. Please do another one on a catalytic stove.

  • @glennlopez6772
    @glennlopez6772 Рік тому

    Having watched parts 1 & 2, it seems that its just a text explanation on the subject. It would be nice, if a cross section of the stove was shown, specially for the secondary air. Additional views woud also be required! Thanks anyway! So we could see the path the air takes!

  • @olivierisidro2696
    @olivierisidro2696 Рік тому

    Pourquoi le bois Nord américain ? Il a quelque chose en plus que le bois européen ou chinois ou péruvien ? 😊😊

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 Рік тому

      On vous invite à écouter la vidéo à nouveau, on ne fait pas mention de ''bois nord américain''. Peut-être que vous faites référence à la phrase ''cette combustion secondaire est typiquement associée aux poêles Nord-Américains et permet à l'appareil de brûler plus lentement''?

  • @wte4603
    @wte4603 Рік тому

    Thanks! Music kind of overpowering and hides the clicks of placement.

  • @jacquesthomassin3079
    @jacquesthomassin3079 Рік тому

    Peut on transformer le modèle mécanique en modèle électronique ? Merci

  • @Savage_420
    @Savage_420 Рік тому

    Nice. Thanks for this. Doing my Caddy door now. Best wood furnace ever.👍👍 🪵

  • @DidTheyEvenTestIt
    @DidTheyEvenTestIt Рік тому

    You depict cleaning out an empty hopper with a vacuum cleaner, however during the winter season a hopper is likely to never be empty. Is this an annual process or do you suggest that the pellets are burned completely through until it's empty before performing that cleaning?

  • @bigmichael21
    @bigmichael21 2 роки тому

    How many BTU can this loop provide?

  • @johnnyplourde1035
    @johnnyplourde1035 2 роки тому

    Bonjour ! j'ai remarqué que ma fournaise Max Caddy ne s'arrête pas a la température par défault, toujours 13 DEGRÉ environs sous l'indicateur par défault! si programmée a 115f le fan s'arrête a 102f! pouvez-vous m'aider s.v.p! merci!

  • @mikebishop5740
    @mikebishop5740 2 роки тому

    Does this require a circulation pump to circulate the water through the tank of the water heater?

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 2 роки тому

      It doesn't require a pump, but a second water tank is necessary and water circulates with a valve system.

  • @shantayprueeissen8914
    @shantayprueeissen8914 3 роки тому

    This time I will do it manually with the help of Stodoys designs.

  • @jfinnigan7106
    @jfinnigan7106 4 роки тому

    J'ai l'impression que mon contrôle d'air primaire ne s'ouvre pas assez. Le disque semble "offset" de 1/2h (15 degrés). J'aimerais verifier - En position ouverte, comment grande devrais etre l'ouverture?

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 4 роки тому

      Bonjour! Il nous faudrait le modèle et le numéro de série. Vous pouvez nous envoyer votre question et ces deux informations au tech@sbi-international.com, il nous fera plaisir de vous aider!

    • @jfinnigan7106
      @jfinnigan7106 4 роки тому

      @@sbi-stovebuilderinternatio6238 C'est une Caddy PF01015. Votre aide est très apprecié!

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 4 роки тому

      @@jfinnigan7106 Il manque votre numéro de série aussi :)

  • @JPDoucet-ArtVisualRecognition
    @JPDoucet-ArtVisualRecognition 4 роки тому

    Ma fournaise à bois Caddy a pour # de série 13947, est-ce que votre kit d'entrée d'air montré dans ce vidéo peut y être ajouté? Merci

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 4 роки тому

      Bonjour M. Doucet, malheureusement votre modèle de fournaise n'a pas d'option d'entrée d'air frais.

    • @JPDoucet-ArtVisualRecognition
      @JPDoucet-ArtVisualRecognition 4 роки тому

      @@sbi-stovebuilderinternatio6238 Merci pour votre réponse rapide! Mais pourtant, les entrées de chaque côté du tiroir de cendre sont bien présentes. Dommage!

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 4 роки тому

      @@JPDoucet-ArtVisualRecognition Contactez-nous au 1 877 356-6663, il nous fera plaisir de regarder ça avec vous!

  • @francoiseraynauld8264
    @francoiseraynauld8264 4 роки тому

    Vous ne parlez pas de la plaque c-cast coupe-feu.

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 4 роки тому

      Bonjour Mme Raynauld, le coupe-feu est situé dans la chambre à combustion de la fournaise, et non dans les échangeurs de chaleur!

    • @francoiseraynauld8264
      @francoiseraynauld8264 4 роки тому

      SBI Dans le manuel d'utilisation, il est mentionné qu'il faut faire glisser le coupe-feu vers l'avant pour que les débris des échangeurs de chaleur (des côtés) tombent dans la chambre à combustion. C'est peut-être pour les plus vieux modèles.

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 4 роки тому

      @@francoiseraynauld8264 Si vous avez des questions concernant l'entretien de votre fournaise Caddy, n'hésitez pas à contacter notre service technique au 1-877-356-6663 ou au tech@sbi-international.com!

    • @israelhoule9873
      @israelhoule9873 2 роки тому

      Bonjour effectivement il serait une bonne idée d'indiquer qu'il faut avancer la plaque coupe feu afin de permettre aux particules de créosote de tomber dans la chambre de combustion. J'ai cherché un bon moment ou elles tombaient pour finalement consulter le manuel ou c'est indiqué.

  • @100Javid
    @100Javid 4 роки тому

    Sa serre à quoi un entrée d’air frais ?

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 4 роки тому

      Bonjour! Une entrée d'air frais permet d'utiliser l'air de l'extérieur pour la combustion plutôt que l'air à l'intérieur de la maison.

    • @100Javid
      @100Javid 4 роки тому

      SBI l’efficacité est tu vraiment meilleur ?

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 4 роки тому

      @@100Javid Ce n'est pas une question d'efficacité. C'est surtout utilisé pour les maisons étanches, pour éviter de tirer l'air de l'intérieur et de créer une pression négative.

  • @Masteur043
    @Masteur043 5 років тому

    comment fait-on pour savoir quand les mises a jour sortent? on peut les downloadé sur votre site internet?

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 5 років тому

      Bonjour M. Pelletier, la mise à jour de la programmation n'a pas à être effectuée de manière fréquente et il n'y a pas de nouvelles versions à télécharger. En fait, la mise à jour sera nécessaire seulement s'il y a un problème avec l'appareil.

    • @Hondamaniac84
      @Hondamaniac84 Рік тому

      ​@@sbi-stovebuilderinternatio6238j'ai un problème où télécharger le programme

  • @traines2332
    @traines2332 6 років тому

    Is this the new Apple hq?

  • @tnt666tnt
    @tnt666tnt 6 років тому

    English???

  • @100Javid
    @100Javid 6 років тому

    La question qui tue Pq plus la vôtre que la Lsbilodeau ?

    • @sbi-stovebuilderinternatio6238
      @sbi-stovebuilderinternatio6238 6 років тому

      LS Bilodeau a été longtemps un client de Caddy jusqu'au jour où l'entreprise décida de simplement copier la fournaise Caddy. PSG est une entreprise qui investit énormément en R et D en plus d'offrir une simplicité d'utilisation et une grande flexibilité d'installation. De plus, le support technique après la vente de Caddy est reconnu comme étant supérieure à LS Bilodeau.