Відео

@@abdallahalabed6850 no. It'll be different wiring and data. I think the 10.25 system has a totally different factor amp with more out puts.

That wasn't my jeep but we got him down to road then went back up and ran johnbull. I'm up there almost every Sunday. Shit happens. No need to get upset. Sux when it does but it is what it is.

Took about an hour of towing it down into big bear. Went pretty smooth all things considered. After we got him down my budy and I went back up and ran johnbull.

Pulled it down with another jeep to road and loaded it up on trailer. Me and the other jeep went back up and ran trail. Things happen just have to be prepared.

What up wess

That one was behind the radio itself.

If i remember the drivers side is the same. Have to go from under with extension. I've been doing this kind of work since the 90s and i can't think of another vehicle that was just a pain doing any thing too.

I was adding audio control LC7 or a DSR1. Either or i was taking higher output speaker lines and coverting them to low level RCA output to send signal to after market amplifiers. That was a customers car i did a couple years back so i don't remember the details of all i did.

Yep. The car that had right away looked like older clappped out civic and we thought his accelerator got stuck on impact because his shit took off. I drove down rd to check if he was alright but he was gone then on way back i found the car that was trying to cross. Old drunk man dumping hi shit in parking lot and trying to stumble away.

I worked on that vehicle 2 years ago. Honestly I don't remember. I work on so many different vehicles.

Haven't had one lock up in a while. Not like the old Honda radios. The new ones even if it says code just give it a sec and it clears itself after data communicates.

@@jeremygallegos4502 that’s good to hear. I bought a radio off a eBay, way cheaper than MSRP. Needed to replace just the screen as it has major bubbling under it (apparently common issues with these models).

I'm about to try a 2022/2023 10.25" screen on my 2021 so we will see but I've heard it works.

@@ericthompson4820 How did it go? Was that a swap from an 8 inch to a 10? I want to attempt it but not sure if the dash cutout is the same size.

The dealer on any thing that new.

I went east at big pine Campground down 3n16 then north on 3n56 then north west at the split on 3n17. About 2 miles up. There's a good peak there and a spot to turn around but the rd if you continue will bring you back out at big pine Campground. But the rout i took is the easiest way id say. If it wasn't for the snow you can make it in 2wd vehicle that has proper tires and a little clearance.

Are you asking if i have knowledge of the center console in that car?

@Jeremy Gallegos if yoknow how remove it, there is a piece in the back but I would like to remove it without remove the whole console

That was a customers car i worked on awhile ago. I don't think i removed any thing from center console. Wish i could be more help.

I just looked it up and there's a kit now. Metra makes it. 107-ki2hg

Did you ever find out?

Following! I have this same screen but all the other grand cherokees show it being separated while mine looks like it's attached to the screen.

I use a site called direct techs but it's thru my shops log in. I can screen shot and send you wiring chart in a email. I've tried to post pic in reply comments but i guess you can't

Yep. Are you looking just to add bass or a 4-5 channel amp?

@@jeremygallegos4502 so what I was told was the only way to put subs in a stock unit the easiest way is to tap into my rear + and - speakers so I just ended up buying a skar audio sdr 10 plus the amp it comes with it was a complete set then I also got a 2 channel line out converter it’s call an lc2i or something I bought posi taps I was told to use the lc2i to basically move the audio from the stock head unit then to the lc2 then to amp (hopefully this kinda makes sense I’m not much of a audio head) rn I’m looking for the speakers wiring diagram for the car and I’m having a hard time finding it on the internet they reason I think I’ll be okay because the base SE seems to not have a factory amp I looked all over the place can’t find one I don’t have any special audio in my sonata ether no Bose

A lc2 requires 12v ground and a turn on. It has built in turn on sensing but some times that cause a turn on/off pop or worse a feed back when you shut off car that causes the woofers to hum away at a hi volume. I like to use the 12v acc wire that turns on radio. All the wires you'll neef to power lc2 are behind the radio. Power and audio.

On the 35 pin harness behind radio 12v constant - red wire pin 11 Ground - black/orange pin 12 Ignition - yellow or blue pin22 38 pin harness Front left- +brown - white pin13-14

I was going to send screen shot of wiring diagram but i guess you can't send images in messages. I'd send link or attachment but you have to have log in. If you want to email let me know or if there's another way to send it on here idk about.

@@jeremygallegos4502 email it to idelarosa15@yahoo.com

What are you trying to add on? those new kias come with most the acc. The amps were easy. Kia doesn't used dedicated Tweeter mid sub speaker lines so no need to sum them. A basic hi to low will work. But I'd use a link6 or the audio control piece.