Відео

Hello, Are you interested in testing our products? We would like to invite you to test the Slingshot Cover for your 2017 Slingshot

Why did ford make it soooo complicated to change headlight bulbs and any bulbs for that matter on front end??

Don't forget about the spacers that go in between that tunnel area that the master cylinder bolts bolts go through

Thanks so much for the video very helpful after taking the part off can u shut the back door 🇺🇸🇺🇸

Would this cause it to be stuck on defrost if it was bad?

Never stand under the spare tire,, rust eats the hanger & wheel & break lines & frame rails & rockers.

Never stand under the spare tire,, rust eats the hanger & wheel & break lines & frame rails & rockers.

I came, I saw, I left!

@10:37 yankee spotted. video saved me some time and hassle, thanks man

They didn't make a 302 in 63.

Watch for cracks in the end housing, over the bendix. Could indicate problems with the flywheel gear !!

What is that tool called that spreads the spring? 2:05

you can also run 2 stop light bulbs in parallel in case one fails

You got hyper flash bro you're going to need to put a load equalizer resistor in there. Or if the fast flash doesn't bother you just leave it alone 👍🏻

""Make sure to put plenty of lube on those pins before you put 'em in..... Just sayin" 😅

Take note weekend mechanics.

Because you're a p****

Pag lube?? Never seen a backwards orfice. Always towards firewall. Glad to see you know a few things

Got that done today, yes that orifice filter has an arrow indicating which way to install.

I know its been 3 years but it's 65lbs, check official Toyota FJ cruiser repair manual.

7:47 Thank you for actually describing how you took that connector off. I'm no mechanic by any means and couldnt figure out how to get that off for the life of me. No other video I looked at showed it or described how to remove it. I know you joked about it taking you 5 hours to get it off but that was an accurate time frame for me haha. Then I watched your video and got the connector removed in a few minutes. I appreciate the video and enjoyed the laughs

Do you need a tool or just big nuts to get that hose off the evaporator.

I cracked a rib trying to pull that hose out. Finally got it after about an hour of fighting it

I like the content by your sense of humor is sickening.. maybe stop talking too much and concentrate on the project.

Thanks Vern, appreciate the help!

Oh man, this guy’s humor reminds me of mine. 😂😂😂

Get a better cameraman!

What is the size of the two bolt you use to removed the rotors!

What type lube for the caliper bolts and brake pad slides?

1st step is to always make sure to remove your fill plug first. If for some reason it’s stripped or broken and you didn’t notice you’re going to be what’s called “FUCKED”! At least until you figure it out or fix it. When making a how to video you should tell the viewer the size of the fasteners which on this vehicle is a 13mm for the cover bolts and can use a 3/8 extension or 3/8 square pipe socket for the fill plug… just clean it will before inserting it to make sure you do not strip or damage it.

You talk too much dumb-shit that don't pertain to anything.

I removed the battery cable to starter, was a pain

Great video. Thanks!

Good work guys I enjoyed your video love the corona

Does the new hinge come with extra hardware?

I'm old school. I like Your Style.

POOR CORVAIRS!!!!!!!!!! You never gave any of them love. I hope they find a good home. SAD!!!!!!!

Bummed to hear you are bailing on the Corvairs.

A Spyder drove up beside her and took Ms Muffet's breath away ua-cam.com/video/C1lHoNG2SHg/v-deo.htmlsi=hLUcIaFpY0fptTKg

Theres a guy in Hurricane Utah you should look up. He cant pass up a corvair Matt Wetzil of Matts Off Road Recovery/Winder Towing. Spelling may be off.

Thank for the video.. can you better your audio? There's a lot of popping going on an it drowns you out. But I get what's important enough to do what's necessary. Thanks again..

What was used to take the plug out?he never mentioned

Here ya go Steve I put something down below .have a good day bro

Every time I see these cars, I START CRYING, I REMEMBER seein my dad in them which is why he bought 3 of them, and 2 58 MERCURYS, HES GONE NOW BUT NOW I GAVE THEM, 🥰😉🇺🇸😁👏👍 COOL CAR, 👍👏👏👍🇺🇸

lmao 8:50

I’m starting to get a weird crack-like noise from my jku ‘11 original tailgate-check when I fully open the gate. So I guess I’ll need to replace it soon. Two questions: 1) why does it break? I’m not even using a larger spare so no extra weight from original 2) what does it happen if the check is no longer there? Does it just prevents the gate to open beyond what’s expected, right? Or it’s there for something else?

Your Mom told you, you are a funny bastard. Sir- like all mommies, she lied. I had to bail. Sorry. This is one awful instructional video.

Do you have use different brake hardline to connect to the new master cylinder I have a 62 bug

What ever became of that engine? Did you pull it or just get it running?

Wow that was terrible crash!