Відео

Where did you buy the engine? Link please

They take a lot of maintenance and taking care of, cheap belts just don’t last period 😢

Well I finally pulled the trigger Team Timemaster! FB $600 going on 3 weeks now and so far I'm liking it took a little getting use to first day with the size difference from my 22 " but now I'm getting the hang of it. Will remember what you said about OEM belts when I cross that path💯👍🏾

WTF man?

That push Mower Definitely Sounds Like It Had Absolutely No Compression When you Guys put Fuel ⛽️ In It And then Tried to Start it.

Thanks for the video! Approximately how much would this cost to have done professionally?

Just swapped my old 190CC for the 223CC from B&S. It was $295 versus the Kohler folks have mentioned was is $200 more. Video was spot on in terms of how to remove the old one and replace the new one. Two points I'd emphasize. Definitely need the tap on the new 223cc 3/8 16th. Also, working to get the three bolts back in place on the new engine took me several tries as things just didn't line up right at first. That bracket requires some wiggling to get it back just right. Agree that putting the bolt on first without the bracket is the way to go. Taking the engine off was <20 min. Putting the new one on and messing with it was more like 90 minutes with trial and error on the bolts.

Ahhh the Toro Timewaster...I've spent as much time working on maintainance on the mower as I have mowing grass.

came looking for how to change the top belt... nothing

This job was done very thoroughly I think you’ll get more than a few years on this truck. Great work. Currently doing this on a 2013 f150

I've been looking at them on FB I still use a 22 on small properties this could save some time 👍🏾

My goodness as tall as you!!!!!!!!!!!!💪🏾

Great video bro 😎 that was a nice clean up I love my toro timemaster…

Yes sir! We break them out every now and then so the customers hear some raking🤣🤣🤣. Thanks for watching and leaving a comment.

Sometimes you just have to break out the old trusty Rake!✔️💯

Thank you for watching the video! I transport the equipment two ways. Sometimes I break the equipment down and loaded into the trailer all the way in the back standing up and position the Ferris right at the end of the trailer the size of the trailer is a 5 x 10 everything does fit. The other way is utilizing my other truck, if I have help, I’ll load up the equipment in the back of the Ford I like doing that better but I don’t always have someone helping. As far as hooking up the Ferris to the cyclone rake, I got a couple pieces of steel hold it together with bolts. Fast forward to now I would not recommend pulling anything heavy with the Ferris Z1. It is not a tractor. You’re going to ruin your hydraulics. Ask me how I know.

How do you fit the cyclone rake and mower on the trailer? Also what’s the hitch you’re using. I’ve been wanting to get the same setup and just stumbled across your videos. Thanks!

Did you tighten the belt tensioner i see you did it hopefully it lasts now

Got it at the beginning of this year in April from lowes been more time broke than actually working

Can’t get through 5 small cuts without it breaking.. definitely not worth the money unless there is a solution for this problem…

I used to mow. I’m retired now, but I know what you mean the oil you never know how much oil to put in the real pain and telling your man I had snapper it was good but they’re heavy Toros. I’ve always had good luck with a time of retired, they came out with the time, I probably would’ve had one. Great video. Thank you.

I like that u talked about peoples dont show the down of the business

What camera is u using. Please

I would add a $7 hour meter so you know what hours you have on that oil so you don't miss doing the oil change on time. What is that red thing with the bungee on the handle bars? I am in the process of doing the same thing you just did, replacing the engine with the same size. I have paid to have it done in the past but I figured I have replaced everything on this model mower at some point and time except the engine so why not. Nobody had a video of just an engine swop. I am having problems getting the old pulley off the dead engine. Wish your video had been out a month ago. thanks

I have a turfmaster and i had a problem with the belt pully making contact with the engine bolt and stopping the pulley from rotating. I had to grind the bolt down.

How's the belt holding up since the install?

Thank you from 2 years in future!!!!!

Lear how to adjust it properly and they last longer! This toro is not even comercial

All day💪🏼

I have time , master it belt eater, 😮

Had the same problem. Don’t order them from Amazon etc. go to the dealer. Get the expensive belts. Mine was eating belts up. Got the experience belts and it fixed it. The blade engagement belt still don’t last crazy long, but king enough. I have 2 of these. Been running them for 4 seasons.

the same thing is happening to me, this will be the 3rd time I am change the same belt

#echo…..👍

I exclusively run my exmark with spindle covers off. You don't want debris finding a forever home on your deck. Imagine a pine cone getting in there. Plus you can easily blow off your deck after every cut. And it looks badass. No one, including the operator, should be approaching the deck with blades engaged.

Quick question.. I purchased a z1 this year brand new. I went to grease spindles today and there doesn’t appear to be zirk fittings on either of them. They are just open holes with grease in them. I used a q tip to clean off the dirt and debris and grease and they look to be threaded. Should I have Zirkfittings on the top of those?Dis you add the kirks to yours? I’m guessing they should come that way from the factory. Seems wrong to me allowing dirt and water to enter spindle bearings.

Is the toro time master worth it I’m thing about buying I have 21’’ Honda push I just started cut grass I have 10 properties

The Timemaster is the ultimate tease of the home lawncare enthusiast mower line. In theory, it's a great concept. Perfect sweetspot for lawns too small for a tractor, too big for a 21" push mower. In practice, it's an absolute nightmare to maintain the unit. The number of pulleys, belts and tensioners that have had constant breakage / replacement / maintenance is mind boggling. What's more mind boggling to me is Toro's complete unwillingness to acknowledge and address these well known issues - for over a decade! The first 1 or 2 generations of the Timemaster? Fine, I get it, it's a new product, these things have to be worked out. We are now > 12 years in to manufacturing of this unit. Can we fix and or address and or update any of these design problems so they actually work and last off the assembly line? No? Why not? The answer is they don't give a shit. How about this as a compromise - can the engineers at least update the design so we don't have to waste an entire Saturday afternoon taking apart the entire machine, to replace the parts which frequently fall apart due to crap quality control on Toro's side? Super, super disappointed in Toro on this front. The second they get real competition in the 28 - 30" mower line I'm never purchasing another Toro product again.

Had one 10 years, probably did 20 yrs of cutting though. The only belt issue I had is with the self propell belt stretching out and slipping. Major pain to change that belt for sure.

Toro belt's are junk started using different one's it helped

Awsome nible machine. Thanks for the video getting ready to change mine after 200 hours 8 years of use. Give it some love. She deserves it. My Z1 has never let me done.

I just bought the same mower over the weekend. So its 2 quarts and a filter per side correct? Thanks for this.....always helps to visualize what will need to be done thru a video.

Great video mate!! Next time get the hydro kit that comes with the fluid filter and an adapter that you screw in where you removed the "bleed" bolt. It has a manual pump that screws to the quart bottle and you can pump the two quarts in less than 5 minutes. The next time just buy the fluid and filters and use the same adapter and pump from the kit used before. A time saver.

Thank you for watching, and Happy Easter to you and yours!!

Happy Easter

Hmmm, my pulling bounces up and down…or has a real bad rattle.

Great Job.

Machine is getting salted. Will rust over night. No offense intended. St. Paul,Minnesota.

looks like a pain in the azz to do. i wonder what the shop would charge to do this?

Brother you are doing great. I just bought the same model.

I've had a 621 QZE for years. It's been abused no doubt. Still runs great, but bought new belt and paddles for it. I've even used it in the back yard to make dog paths to go potty. I like the Ariens you have in the truck. I picked up a 28 inch Ariens last year. We got a lot of snow last year, only used it once this year. But it's great for clearing out what the plow puts in the driveway.