Відео

Yes you do have to fly faster with the petg or heavier materials that is for sure. I'm still trying to find a good link on how to set up a gyro properly with an elevon if there is any information that be fantastic

Fly's great! I've just finished the same scaled-up version @ 120% for my freeing edf.. What was your build weight without a battery? I'm at 800g, a little heavier than I wanted, too much infill. thanks!

PetG does has it's advantage, sadly sanding it to make it look all nice for painting is not one of its strong points.

Nice....so...overall sound difference...better/worse...i know the sound thing is subjective...but its the high pitch whine i would like to eliminate... I like the custom rear stablator upturn tips....👍👍

Good stuff... necessary

Michael Moran build some great motors 👍👍

Hi Whats Your Email ?

May i ask why you usel ASA instead of LW pla?

Great flying! What rates did you use?

Go to forward programming and adjust your pitch in safe mode.

now do the thrust vector version!!!

The airplane is too far away for us to tell what it's doing. - and you could tell us when it's 1/2 throttle and when full throttle (when it's close enough to observe performance)

Thanks for your reply. Going to try it now

What the conclusion after 3 months regarding 4s on stock electronic ? Thanks

Holy!!!!!!! Now its a kyle video. Lol great job man, dont give up you got this

Nice job, proud of you. The excitement in your voice. 😂😂😂

Great video! The left sound channel is out, though.

Congrats

Look at you!!

Brillant Job Chris🙏🏼🙏🏼👍

Are the files available?

Nice. What gyro did you use?

Nice thanks for the description.

Awesome maiden!! Can’t beat the old F22

So I assume you scaled up the original version to accommodate the 64mm instead of 50mm? Or will a 64mm fit the original? Great job by the way!

Did you enlarge the whole plane by what %?

Why not leave the gyro on in winds like that?.... Also try abs it's a little harder to print depending on ur printer but lighter than pla or petg and very durable..

You should try ABS! It is 20% lighter than PLA and has a lot of benifits

Any news on this? I don't see any files for this size and based on your comments we cant just resize it right? This little thing is so cool.

Thanks 👍for this experiment. I too wondered if it was possible for a more budget and robust filament with his designs. I prefer flying them versus reprinting due to my inexperience hand launches and buddy launches 😂. Finally got a few dialed in and actually flying. LW is probably the correct way to go but preference wise Cleaner and less fuss with basic PLA etc…either way they all damage eventually. Just less on the filament cost at least and better accessibility. Only downside for me is crap flight times 😊but still fun at least.

I love it, this models are so nice, is a crime to flight them, LOL Nice job.

Mine is printed in white LW-PLA, TO-weight with 1550mAh 4S is 670g. I maidened it on Saturday 14.09.24, calm wind, a bit coudy. It flies great right from the start ( I use a catapult ) with no gyro. 2 things to mention : 1 - It needs colour. It was difficult to see the orientation when it was far away. 2 - Don't use cyano-glue to glue the elevons as it does not realy stick on the servohorn-material. I lost one elevon at the landing ( no damage ) and could easyly pop of the second one. I use hot-gue now. As I see your experience right now, I will print the F-16 also in PETG, Thank you for the video.

That is so cool. Do you have a fpv camera mount that you can put on your plane?

Hello the jet looks great I’m trying to print one my self but having a hard time with the printer setting you wouldn’t of happened to have print this on a raise 3d printer did you

Did you have an autopilot in it, just looking how the elevons react when you were moving it pre launch.

Hi Chris, how are you getting the outer surface wall so thin? What thickness do you set the printer at? Thanks.

Looks good! Im justvstarting ro print my 79mm version. 😊

Love it.

Yeeeeessss you beat me to the 64! Amazing video. Love the dual camera and commentary 👍🏻👍🏻

Super flight and super camera view, do you start from Gras with the 64?

So beyond saying "flies great" sure woukd like a bit more details. I bought the plans but havent printed it yet (doing too much with the Mini-Delta where I've modified the intake for better airflow efficiency). So expo, printing tips, other flight characteristics?

Very cool build! The mixed colors definitely give off the cartoon vibe. It says Im out here to have fun! Good stuff man

hey dude nice video but the sound is to low just so you know

Thank you so much, I have been asking Kyle to do a video like this for so long. And I have been looking for a video like this. I would like to get a shared settings just to have a place to start, and then dial my printer in from there. 😊

Love this designers models. Printing another mini delta now

No matter What.......always do a flight check, and this is why. Good save.

DUUUUUUUUUUUDE what a save!!!!! thats some fantasic flying right there. Great Job getting that beauty back to the ground!

Wow did he bring that in with a rudder only??

🙏 thank you for the great video, I just finally picked up an A1 and was curious how to start printing plane parts with LWpla and heard so many unique techniques to get usable prints. You have definitely provided a great starting point that I have found with this video 👍 I know LW in this area is the way to go as my first experiment with regular PLA dropped like a rock 😂 I knew then back to the drawing board. LW from these known brands obviously aren’t the cheapest options, have you had any success with any particular brand purchased from Amazon you can link too? Thanks for the content…

Sorry about the generator,! See ya tomorrow