Відео

Here is my story with my DSL40CR amp I had 2/3 years ago. My DSL40CR had no output at all. literally. I took it to an amp tech. He said there was no output from the front of the amp, the fx loop (which bypasses the pre-amp), or emulated output jack. The tubes tested good and even swapping them with other tubes changed nothing. The speaker was fine too. The internal board mounted fuses were not blown either. The only sound coming out of the amp was an occasional pop or crackle. He then did some googling around and saw talks about a socketed module inside the amp that is known to have issues. The firmware on the soldered EPROM can become corrupted and mess w channel switching functions. that was that exact issue bu the voltages on the pins of the module shown from a partial schematic did not match what he found inside my amp, so that led him to believe that was the issue. So he contacted Marshall , they referred him to a parts retailer from AZ where he can order a replacement module. He also conferred with other techies and they encouraged him to also replace the main board as well. So he ordered a logic board and a main PCB. Those took a while to arrive, but he got them, did his magic and finally, my amp was fixed. I bought the amp in 2020 off Reverb barely used for $620 and that was such a crazy deal. It worked beautifully for the first year I had it but then suddenly , the no output issue occurred. I didnt get it fixed till a year after that cuz I had no money. So with the cost of the repair which was another 600 cuz of the labor and parts, I pretty much spent the same as if I bought it new which sucked. but at least its fixed and the tech did a hell of a job. His @ on instagram is @culen if anyone is from Los Angeles.

mine did that now make No Noise. I just changed power tubes and nothing again. Anything else could be a problem? thank you.

What was the issue? Mine sounds the same after 2 weeks

First try rebiasing... Mine needs it done at least 1x per year. I swear it's because of switching from low to high power too often. Now I only play it in high and it seems to have helped. Had mine for almost 4 years now.

Super vidéo ca te dérange si je t'emprunte t'as vidéo pour compléter la mienne en échange d'une mention ?

These amps are junk! Do not buy!

Why don't you reach out to Marshall versus posting it on UA-cam?

Yes there even seems to be a fragment of popping. Tube change. Most go with jjs

Marshall sucks nowadays they are trash

The 3 maes at least 100hp more

Here the echo behind ya lol poor little toad

Just got mine in a few days ago, and still can't figure out why I can't get sound out of it. I might just have to start a return, because I shouldn't have to immediately shell out for repairs, after just paying $800 for the damned thing. I didn't expect it to be the greatest, but I was expecting to be able to at least get sound out of it.

Sam wore the Maple Leafs jersey when they were in Toronto. Glad to know he'll show love for whichever city he visits.

May 3rd or 4th?

Olé, olé olé olé

I was there, my phone died after Nihilist, thanks for posting the video. Fantastic experience!!!!

Very well played my friend! cool guitar collection🎸

I've got the Same Issue with an Fame VS5012 (Randall RG50TC), but only in the Clean Section...sent it to repair, tubes got switched to new ones...a few weeks - no problems...in my case it seems to be a problem with the Inputjack. When I put the Cable in and out and in and out, it goes away. :D

Did you check the Biasing on the Tubes. Mine was way off when I bought it new. It has Biasing Ports on the back of the Head to set the Bias and balance the Tubes.

Mine is super quite with stock tubes. I've had to 2 years.

Can I noise killer pedal fix the problem?

allahınızısikiyim cok iyi

I have exactly the same problem , same noise on Both 20w and 40w , i have to change all the tubes ?

il mio non fa rumore!!!

Słaby kawałek i zła akustyka, ale lubię ich.

amazing performance

Im having problems with my dsl40c cutting out

dayum... bro has an e46 and a girl bro is winning life, and i hope someday me too :))

Dirty Pot

Same problem. Replace the power tubes and reset the bias.

Mine is doing the same thing. Were you able to solve this issue? Thx.

dsl 20 cr hat gleiches Problem.!!!

man you are so lucky

Sully can jam on the drums. Sounds great!

this never gets old.

Noise gate 😂

Jamais vu le MTELUS aussi plein. Tellement de monde que 90% du temps y'avait même pas assez de place pour un pit... Tout un show!

3:13 did michael paget give you a little smirk there. Was at that show. Amazing

Still got it 💪🏻

I was in that pit haha 👌

Jy etait aussi jai tripper ma sainte criss de vie de les voir pour la premiere fois

This was the best show I have seen this year. The energy was insane.

That was a epic show🤘🤘

Méchant bon show hier!

I was just about to buy this amp because it was recommended by an amp technician. But now I'm seeing this? A comment by @NCSandS relaced the original power tubes with JJ Tubes and fixed the problem. So now I know that if I get this amp, I might as well buy a set of power tubes when I make this purchase.

That's dirty pots just some air duster sprayed into them will fix it

Pre amp tube was gone in mine

Grounding issue i think? Idk but from what ive heard these amps really easy to repair, so hopefully the fix wont be too much

Same thing with the used one I bought ://

had mine for 4 years now still no issues so far.