Відео

So the New Holland has a door that opens out.....and yes you have to be mindful of where the boom is when you want ot get out of the machine....but you cant break the door off as the machine wont operate with the door open. I've got the NH C345 and it is great. I looked at the Kubotas and love the sliding door.

👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎

Got tired just watching that! Lol Good job!

nice cleaning up after a project, unfortunately it doesn't stay clean too long once the next project rolls in

Next project, the John Deere 530?

I would pull your carb off and split the halves and check the faces to see if they're flat. Those carbs have a bad habit of warping at the screw points. If it's warped it'll leak gas at the seam, and it'll leak air and make the carb not work correctly. Congratulations

Congrats!!! My dad's got a 460 wide front also that's been sitting for many years. I'll definitely be looking back on your videos if we decide to get it running. Keep up the good videos 👍

Winter wheat update ??

My 606 with the same engine starts good but is very cold blooded.

A nice looking 460. I like those models.

I felt the same way when I pulled my project tractor out of the shop the first time, good job!!

Good job. It's rebuilt.

Pretty much a year in the making correct?

My 606 loader tractor is basicly same hy tran system as 460. It has VERY noisy whine. I changed hytran and filter with no change.

Where was the auction

She sounds good!

Great to burn brush piles ect

I dare you to try to do a burnout with it once its finished

You might have to look into the governor to solve your throttle issue

If you need to get rid of the oil a lot of your parts house like Oreillys, autozone, advanced auto usually take waste oil as long as there isn’t too much water or gasoline in the oil.

I do like where they put the hydraulic filter on your tractor on my 454 it’s behind the rear wheel it’s getting there and you have a good helper

Old oils r good for chains on ur machines.

Those bailers you looked at seemed in poor condition. I used to have a 336 and would not buy one again. Why did you not look at the NH bailers?

Being willing to walk away empty handed is a sign of wisdom. Know yourself and your situation. Thanks for sharing

Talcome baby powder makes tube slicker.

I have good luck with a brush and Rustoleam silver, no over spray on tire.

Wish I had a winch sometimes. When ever I cut a tree it always hangs up into another tree, never falls to the ground. Get as close as I can with tractor and pull it till it falls. Sometimes tractor has trouble pulling it free.

Just found your channel. First time watching. OMG is that a HUGE auction! I would love to go to a sale like that! If you are thinking about a 6620, you should definitely been in on that one. It looked good, and that was dirt cheap. And the 6620's were good combines. There were some really nice 7000 JD planters there too. That four row was really nice. That one New Holland square baler you stopped at for a bit was nice. Don't be afraid of a New Holland square baler. Probably better than the Deere. There were some nice older International tractors there that probably went dirt cheap judging by what the stuff sold while you were there. That newer Case Magnum that sold for $48K was definitely a big steal! Which part of the country are you in?

What I like to do with my timing marks is to clean them well, mask off the area, and then hit the balancer with a contrasting florescent spray paint. As soon as you spray it, wipe the balancer off so you're only leaving the paint that's in the timing tick marks. That way, the timing marks will just about glow under your timing light. Nice series, and you've got a good approach to things.

... locked-up steering on running gear pulls straighter and preferred by some ...!

I can’t believe you took us to a auction and didn’t buy anything😢

Just found your channel I was at that sale too I bought a hesston 530 round baler there

That baler that sat out side looks hardly used I would just throw diesel all over it and wipe it down

Stay away from the twine balers and buy a wire tie baler. The wire tie balers are easier to work on and have less moving parts than a twine tie.

Good to seed it on all four the guy who did my tires put a lot more air in till the bead was fully seated on the rim then backed off on the air and Happy New Year’s

I have 606 IH with loader and do the lazy thing with card board under the leaks. Loader has the worst leak on the single hyd cly that tilts the bucket. Very unique cly was rebuilt for over $300 and still leaks bad.

Those r for duals.

Needs more snow

How's the 460 coming

Not seen the little John Deere for a while have you sold it

When is 530 up to run

beautiful tractor built to last forever greetings from 🇳🇱

Whatcha gonna do if someone orders 100000 lbs worth of corn? Lol

Luv the JD 440 snow mobile!! Always wanted one we ivwas a kidd....still do....lol

We had a New Idea Uni 701 with a 3 row head that we picked ear corn with at my uncle's around the late 90s and early 2000s ( when I was in my teens ). Before that we used a 770 Oliver with a 2 row mounted picker. Watching this brought back memories lol.

Why not bean then wheat after that?

You need a pull type offset disk

You definitely need some weights on that disc

Chisel.plowing is a good feild preperation tool.with the diskblades on.the front of the chisel plow.

You csn adjust your down pressure on.your tractot fot deeper cuttinh