Відео

hall effect is trash for fps gaming , avoid it if you mainly play fps competitive games

My left one is no longer calibrating, only the right one, what could it be? I already calibrated it previously, but now I only calibrate the right one.

Does anyone have an idea whether this board will work with new Gullikit TMR joysticks on DS Edge as well?

Will the Guilkit TMR modules work with these circuit boards?

Is there a button combination or data pad that can be used to factory reset the driver board to start the calibration over?

Will TMR modules work with any of your circuit boards?

Is there a specific hall effect joustick i must use?

After v5 and v51 are installed on the Xbox Series X controller, can I normally update the controller firmware when available and calibrate it from within the Xbox Series X itself? Why did those yellow hall effects cause a bug after calibration?

After v5 and v51 are installed on the Xbox Series X controller, can I normally update the controller firmware when available and calibrate it from within the Xbox Series X itself? Why did those yellow hall effects cause a bug after calibration?

After v5 and v51 are installed on the Xbox Series X controller, can I normally update the controller firmware when available and calibrate it from within the Xbox Series X itself? Why did those yellow hall effects cause a bug after calibration?

I need a video on how to calibrate it

It's quite complicated to install! 🥲 But it's helping me practice 😂, my first two attempts were unsuccessful, for some reason the top of the circularity test reached the corners, like when the magnetic stick is just installed without this board, but the bottom of the circularity test didn't reach the edges properly, I got frustrated so I left it for another day.

please tell me how can I enter the settings in the pad to calibrate it like that because it doesn't work for me,

Jun, how thick do the insulating tubes need to be? And why did you remove the LT trigger sensor but that step isnt described in your installation manual?

Like someone asked before : can this be used to calibrate xbox elite (v1) controller? Can you share the link to the replacement parts? And link to software please?

with no explanation, and no reponse, this video is useless..

Why does the left joystick sensor need to be removed in the first place

how do you do it? through some program or website? please provide solution. because my pad has too little range

Hello, please tell me if there are flydigi apex 4 stick modules for sale, or maybe you know people who have them. Thank you

Can this work with TMR sticks?

Does anyone know if you ould do this with a different hall effect module

I followed everything as on the video, I can only calibrate mode A. When I want to go to S or B mode, I always end up in A mode. What is the problem?

What would you recommend if I managed to take off the potentiometer (original) piece and accidentally removed some of the "pads" or contact points in order to put in the new hall effect potentiometer I have no contact point to be able to solder in 2 locations. I tried to "bridge" solder over and not sure if it worked or not because my controller just blinks white now. I didn't know that the dualsense edge needed a separate calibration board before starting the replacement. By the time I found out I already had started. I guess my question is there any way I can still salvage the pcb and use it to make it all work? Or do you know how I'd be able to find a replacement pcb? I feel like I might be stuck with having to buy an entirely new replacent unit (which I don't want to do) please help 🙏🏼

Apakah ini berlaku buat ps4?

Ok.

What do you think about the new Gulikit TMR joystick?

is there a version of the replacement stick that doesn't need the small circuit board to be installed? Also, about "threaded Hall joystick will have size incompatibility issues", what seems to be the problem with those models? i see them everywhere

I’m having issues with my Link hall effect stick. It doesn't stay centered and jumps back and forth. For example, when I press the left trigger and move the stick down at the same time, after I release the trigger, the stick moves up again. Does anyone know what might be causing this problem?

Hello. Could you tell me what is the difference of between v4 and v5.

works from steam too. once steam controller settings control windows with game pad

I installed this mod in 07/08/2024. It takes me about 1.5 weeks to install this setup. Because i am new to soldering and i don't have the equipment, so it takes me this long to do. First time to soldering beware as it requires time and patient to do. It has steps that need to be done right in order to work well. Lucky, my controller works perfectly with this driver installed. It has circularity error on both sticks around 3~4% My experience: 1. It takes some time to install the driver as the board require some bridging and wiring. Things are too small to install and require multiple times to apply solder like the middle pin of the hall effect sensor with bridging wire. 2. Need to make sure your soldering is very clean and no accidental connection to other connections. 3. No Step by step instruction in the box. Have to rely on the video (Though the video is very well explained) 4. The first step of removing the joystick is already an hard task without heat gun. Remove joystick by cutting off pins is a good option for soldering iron 5. You are given two pair of joystick. You are suppose to transfer the sensor from one pair to other. 6. There is still a micro jittering in the end. Not sure its my fault or joystick fault or accidental connection. 7. I recommend static mode than dynamic. It make life easier if you forgot about it. ( Centre Point Mode switching ) Good: . It really works as advertise. I have 3~4% circularity error on both sticks . Calibration works as the video shown. All mode A, B, S works. Turn off calibration works. Centre Point Mode switching works. Bad: . Its really difficult . Still have a bit micro jittering If you have any question, just commend below. I try my best to answer

I installed this mod in 07/08/2024. It takes me about 1.5 weeks to install this setup. Because i am new to soldering and i don't have the equipment, so it takes me this long to do. First time to soldering beware as it requires time and patient to do. It has steps that need to be done right in order to work well. Lucky, my controller works perfectly with this driver installed. It has circularity error on both sticks around 3~4% My experience: 1. It takes some time to install the driver as the board require some bridging and wiring. Things are too small to install and require multiple times to apply solder like the middle pin of the hall effect sensor with bridging wire. 2. Need to make sure your soldering is very clean and no accidental connection to other connections. 3. No Step by step instruction in the box. Have to rely on the video (Though the video is very well explained) 4. The first step of removing the joystick is already an hard task without heat gun. Remove joystick by cutting off pins is a good option for soldering iron 5. You are given two pair of joystick. You are suppose to transfer the sensor from one pair to other. 6. There is still a micro jittering in the end. Not sure its my fault or joystick fault or accidental connection. 7. I recommend static mode than dynamic. It make life easier if you forgot about it. ( Centre Point Mode switching ) Good: . It really works as advertise. I have 3~4% circularity error on both sticks . Calibration works as the video shown. All mode A, B, S works. Turn off calibration works. Centre Point Mode switching works. Bad: . Its really difficult . Still have a bit micro jittering If you have any question, just commend below. I try my best to answer

How is it going with the EU procedures? I really want to buy a few of these but I still can't buy them in the EU.

Is there a way to reset the settings and start over? After I calibrated, it won't let me get into different modes for the right stick. Please help.

Calibration does not work. I've installed this driver in hope to reduce circularity error. My experience: 1. Bad: Very time consuming installation. I am an experienced electronics guy with more than 15 years of work. I have all the equipment I need. But even then the time invested does not match outcome. 2. Good: Truly solves stick drift. 3. Bad: Calibration does not works for the right joystick at all. The left joystick allows entering in mode A, mode S and mode B. In mode B left and bottom calibration directions does not have any effect. The right joystick allows calibration entering from time to time. My assumption is a bad firmware unable to handle sensor noise. 4. Bad: Circularity error on both sticks is about 20% even after multiple hours of calibration tries. 5. Good: Well in the end it lets me play again. Astro's playroom seems to be fine. Dead zones of joystick (e.g. circularity) can be percepted indeed. Overall advice: Do not buy it and do not invest your time in it! Maybe some simple hall sticks would perform same. Used controller is PS5 dual sense one.

I've gone through calibration about 20 times now. I keep getting a 20% avg error. Is there a way to adjust the overflow on the corners because it maps out a perfect square. Has anyone had the same issue?

Attempted and failed miserably. Make the pads for the middle sensor pins bigger! Couldn't get the solder to stick to it even a little bit and just wasted so much effort on this. DO NOT ATTEMPT UNLESS YOU ARE SIGNIFCANTLY SKILLED AT SOLDERING!!!

Do you sell the finished product?

Hi, I tried installing with my scuf reflex controller for ps5 but my paddles doesn’t work anymore … can you do a video with scuf reflex fps controller ?

Hi, does it work with scuf reflex controller ps5?

Sadly Aliexpress tells me it cant be sent to germany. Is there a way to enable it?

Where can i buy these? im looking for them everywhere!

I did these on my Xbox wireless control. Both sticks are pretty centered and are responsive. The only issue I have is that the right joystick is not saving my center point. And it also won’t go into B or S mode on the right joy stick. Left joystick is fine and calibrates.

Does the controller need to be completely reassembled for it to go into modes properly? I have it mostly assembled but i havent connected everything like the mic. When i try to go into calibration modes, it only lets me set one axis on one stick and the opposite axis on the other stick. The other respective axis on each stick sweeps normally rather than make step adjustments to center. Pushing the sticks down doesn't seem to change modes.

dose this work on the ps5 edge controller?

Does this apply to the Xbox wireless control as well?

Is there a reason you do not connect the left trigger hall effect Sensor to the LH calibration board, like you do for the regular Xbox controller?

B mode isn’t working keeps putting me in a mode I press the stick down and go whatever direction still puts me in a mode

Hey, listen - I've installed your kit on my xbox series x controller, and I'm having a problem with the right joystick - the axes are reversed! Up-down, right-left. I have checked all the connections and everything is ok.... have you encountered a similar problem?

Well, if that's how much solder you put on there no wonder it's so damn difficult to get the original joystick out of the PCB